P改性NiW/γ-Al2O3的低温焦油芳烃组分加氢性能研究

以γ-Al₂O₃为载体,采用浸渍法制备了不同P添加量的负载型NiW加氢催化剂,采用固定床加氢装置,对模型化合物萘和低温焦油富集的芳烃组分进行了催化加氢。催化剂采用N₂吸附、XRD、H₂-TPR、XPS以及NH₃-TPD的方法进行表征,加氢产物采用GC-MS和GC×GC-TOFMS进行分析。结果表明,P助剂能够扩大催化剂的孔径并促进活性金属组分在载体表面的分散;当P含量为1.0%~1.5%时,能够促进Ni-W-O混合相生成,并提高催化剂表面弱酸的含量;萘加氢反应的转化率和十氢萘的选择性也在添加1.0%的P时达到最高,分别为80%和50%左右;低温焦油芳烃组分的催化加氢结果显示,芳烃饱和加氢反应占优,绝大部分芳烃转化为环烷烃,且催化剂具有显著的脱除杂原子效果。     

复合氧化物负载的Ni基催化剂上愈创木酚加氢脱氧性能

分别以Al₂O₃-SiO₂,Al₂O₃-TiO₂,TiO₂-SiO₂和TiO₂-ZrO₂双金属氧化物为载体研究Ni基催化剂的愈创木酚加氢脱氧性能. 重点考察了催化剂载体、溶剂种类、反应温度和压力对愈创木酚转化率及产物选择性的影响,并对催化剂的抗积碳性能、重复利用性能和愈创木酚加氢脱氧反应机理进行了探讨. 通过BET（Brunauer-Emmett-Teller）比表面积、X射线衍射（XRD）、NH₃程序升温脱附（NH₃-TPD）和H₂程序升温还原（H₂-TPR）等表征手段对催化剂的比表面积、物相结构、表面酸性、可还原性能进行了表征. 结果表明,Ni/TiO₂-ZrO₂催化性能相对较优. 在300 ℃、初始氢压4 MPa、以十氢萘为溶剂的最佳反应条件下,愈创木酚的转化率为100%,环己烷选择性高达86.4%. 该催化剂还具有抗积碳性能,反应后的催化剂上仅检测到3.2%（质量分数）的积碳量.     

Pd/ZSM-5/MCM-41催化剂加氢脱硫性能研究

本工作将三种材料：全硅MCM-41 （Si-MCM-41）、通过机械混合Si-MCM-41和HZSM-5得到的Z-MCM-41-M、通过在HZSM-5外部包覆Si-MCM-41制备得到的Z-MCM-41,采用XRD、N₂吸附-脱附、NH₃-TPD、Py-IR手段进行了表征.分别以这些材料为载体,制备出负载型贵金属Pd催化剂,以二苯并噻吩（DBT）为模型化合物,在固定床反应器上进行加氢脱硫（HDS）性能考察.反应结果表明,载体的表面积或分散程度并不是影响负载型Pd催化剂HDS性能的关键性因素,催化剂的HDS性能受到载体的孔尺寸和载体的酸性双重影响.负载在酸性载体上表现出较好的HDS性能和加氢选择性,与溢流氢有关.其中,在三种催化剂中,Pd/Z-MCM-41催化剂表现出最高的HDS活性和优异的加氢活性,说明在载体的介孔孔道结构中引入微孔的酸中心对提高加氢脱硫活性有重要影响,仅靠机械混合方式制备的载体不能将介孔的孔道优势与微孔的酸性优势表现出来,不能产生较好的协同催化作用,具有介孔孔道结构和适中酸性的Z-MCM-41复合材料是潜在的贵金属加氢脱硫催化剂载体.     

分散型纳米二硫化钼的制备及其对模拟油浆的加氢处理催化性能

以二烷基二硫代氨基甲酸钼（Mo-DTC）和六羰基钼（Mo（CO）₆）为前驱体、水热法合成了分散型纳米MoS₂,采用X-ray射线衍射（XRD）、透射电子显微镜（TEM）、X射线光电子能谱分析（XPS）和程序升温脱附法（NH₃-TPD）等方法对其进行了表征。利用三种烯烃（辛烯、苯乙烯、反式二苯乙烯）、苯并噻吩和蒽等构建模拟油浆体系,结合气相色谱-质谱（GC-MS）分析,对分散型纳米MoS₂的模拟油浆加氢处理催化性能进行了研究。结果表明,不同预处理条件下制备出的催化活性样品均为2H-MoS₂,但各样品的结晶度、颗粒尺寸、硫化程度及其酸性质等均有所不同,其中,总酸量差别较小;以Mo-DTC和Mo（CO）₆为前驱体的优选硫化条件分别为380℃/30 min 和370℃/30 min,所得到的催化剂对烯烃和噻吩的加氢活性较高。其中,Mo-DTC基纳米MoS₂催化剂的烯烃加氢饱和转化率高达98.10%,加氢脱硫率为94.51%,而蒽的部分加氢饱和转化率则较低,为29.47%,且无八氢蒽（8HN）或全氢蒽的生成。Mo（CO）₆基纳米MoS₂催化剂的加氢效果则略差,烯烃加氢饱和转化率为94.01%,加氢脱硫率为89.01%,对蒽的加氢饱和转化率为24.20%,无8HN或全氢蒽的生成。总体而言,由Mo-DTC所制备的MoS₂催化剂具有烯烃高效饱和、含硫化合物高效脱硫、芳烃浅度加氢饱和的效果,且油浆加氢处理反应的选择性及催化稳定性均更高。     

草酸二甲酯气相催化加氢合成乙二醇的研究

采用共沉淀法制备了一系列 CuO/SiO₂ 催化剂,进行草酸二甲酯气相加氢活性评价,分别考察了不同沉淀剂（Na₂CO₃、NH₃·H₂O、NaOH）、催化剂组成以及反应工艺条件对加氢性能的影响。采用N₂ 吸附脱附、N₂O吸附、XRD、TG热重分析、H₂-TPR等手段对催化剂进行表征。结果表明,草酸二甲酯加氢反应活性与Cu⁰有关,提高铜比表面积有利于提高加氢活性。采用以NaOH沉淀剂制备的CuO质量分数为50%的CuO/SiO₂催化剂,在200℃、2MPa、0.07h^-1和氢酯摩尔比为100时,草酸二甲酯转化率可达 98%,乙二醇选择性87%,且催化剂表现出较好的稳定性。     

二维M-Co3O4负载Ir对香草醛加氢脱氧性能研究

以二维金属-有机框架M-Co₃O₄为载体制备了具有高活性的Ir/M-Co₃O₄催化剂.采用X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、电感耦合等离子体发射光谱仪(ICP-OES)、 N₂物理吸/脱附等方法对催化剂进行了表征,并研究了催化剂、温度、时间、溶剂等因素对香草醛加氢脱氧反应的影响.结果表明, Ir/M-Co₃O₄催化剂具有较好的普适性和稳定性,在香草醛加氢脱氧制备4-甲基愈创木酚(MMP)反应中表现出较高的活性和选择性,香草醛的转化率达100%, MMP的选择性不低于99%.     

氟添加方式对NiMo催化剂在浆态床上加氢脱硫性能的影响

以F为助剂,采用完全液相法制备了氟改性的NiMo/TiO₂-Al₂O₃浆状催化剂,考察了氟的添加方式对催化剂在浆态床上4, 6-二甲基二苯并噻吩(4, 6-DMDBT)加氢脱硫性能的影响.采用X射线衍射(XRD)谱、氢气程序升温还原(H₂-TPR)、N₂吸脱附实验(BET)、X射线光电子能谱(XPS)、高分辨率透射电镜(HRTEM)对催化剂进行了表征.结果表明,在不添加浓硝酸的情况下,在活性组分加入之前引入氟能显著提高催化剂的比表面积和孔径,促进反应过程中金属镍在催化剂表面的分散,更大程度地减弱催化剂中活性金属与载体间的相互作用,有效提高Mo的硫化度及MoS₂的堆积层数,从而生成了较多的II类Ni-Mo-S活性相,促进芳香环的加氢和C-S键的氢解,对4, 6-DMDBT有较高的加氢脱硫活性.     

Ni2P负载量对Ni2P/Ce-Al2O3催化剂结构及萘加氢性能的影响

采用程序升温还原法制备了一系列Ni₂P/Ce-Al₂O₃催化剂,考察了制备过程中Ni₂P负载量对催化剂结构及萘加氢饱和性能的影响。结果表明,Ni₂P负载量可调控活性组分Ni₂P与载体Ce-Al₂O₃之间的相互作用,进而调变催化剂的比表面积、Ni₂P粒径及催化剂活性位点数量。当Ni₂P负载量（质量分数）为17%时,催化剂具有较大的比表面积（40 m²/g）、较小的Ni₂P粒径（26.3 nm）和最多的活性位点数量（26.7 μmol/g）;同时,该催化剂萘转化率为95%,十氢萘选择性为76%,且活性稳定性良好,这主要归因于催化剂大的比表面积和高的活性位点数量为反应提供了更多的场所。     

Ni2P和MoS2催化剂在喹啉加氢脱氮反应中的协同效应

设计实验证明了Ni₂P和MoS₂催化剂在喹啉加氢脱氮反应中存在协同效应,该协同效应能够用氢溢流遥控模型理论解释。Ni₂P//MoS₂的协同因子随反应温度升高而减小,并且略微大于相同反应条件下NiS_x//MoS₂的协同因子。Ni₂P产生的溢流氢能够提高MoS₂催化剂上加氢活性位的数量,促使Ni₂P//MoS₂催化体系增加1,2,3,4-四氢喹啉和5,6,7,8-四氢喹啉加氢生成十氢喹啉的速率,提高其脱氮活性;因此,Ni₂P对MoS₂催化剂是很好的助剂。     

硼掺杂还原态氧化石墨烯催化剂的制备及其蒽催化加氢性能的研究

制备了一系列硼掺杂的还原氧化态石墨烯催化剂并应用于蒽加氢反应。结果表明,随着催化剂处理温度的升高,催化剂中有序碳结构会发生变化,硼会取代材料骨架中的碳,进而影响蒽和氢气的吸附活化。经硼改性后,催化剂对蒽加氢反应表现出了很高的加氢活性,蒽的最高转化率可达97%,深度加氢产物八氢蒽的最高选择性可达19%。     

Pluronic嵌段共聚物F127和P123胶束对萘、蒽、芘的增溶

35℃时F127和P123在ccm后可生成内核PO成分分别为92.7%和94.5%的胶束,后者胶束内核体积为前者的2.8倍.稠环芳烃和空胶束的第一步缔合平衡常数K₁值均随萘、蒽、芘顺序逐渐增大.萘、蒽、芘在每个F127和P123胶束中的增溶量均随胶束内核体积增大而线性增加,每个PO基团对应的增溶量比十二烷基磺酸胶束内核中相同体积对应的增溶量约大近2倍.Pluronic胶束除与稠环芳烃间具有强相互作用力外,所形成的大内核是导致大增溶量的重要因素.     

Polycyclic aromatic hydrocarbons (PAHs) in edible oils by gas chromatography coupled with mass spectroscopy

The occurrence of polycyclic aromatic hydrocarbons (PAHs) in nine edible oils of three categories of oil samples, such as soy bean oil, mustard oil and coconut oil, has been studied to determine the contamination degree of this type of oil samples. Eight major carcinogenic polycyclic aromatic hydrocarbons (PAHs), such as naphthalene, anthracene, phenanthrene, fluorene, pyrene, crysene, benzo(a)pyrene and benzo(a)anthracene, were identified and quantified in the extract of edible oils collected from Bangladeshi Markets by gas chromatography and mass spectroscopy. All of the carcinogenic PAHs are not present in the edible oils. A few of the carcinogenic PAHs are present in the oils but it is within the permissible limit. The results for the recoveries of naphthalene, fluorene, phenanthrene, anthracene, pyrene, crysene, benzo(a)anthracene and benzo(a)pyrene were in the range of 56–84%. The limit of detection (LOD) of the GC–MS method, established at signals three times that of the noise for naphthalene, fluorene, phenanthrene, anthracene, pyrene, crysene, benzo(a)anthracene and benzo(a)pyrene, was 2.0–2.5 ng, respectively.     

Infrared Cavity Ringdown Spectroscopy of Jet‐Cooled Polycyclic Aromatic Hydrocarbons

Infrared absorption spectra of the CH stretching region were observed for naphthalene, anthracene, phenanthrene, pyrene, and perylene using a heated, supersonic, slit‐jet source and cavity ringdown spectroscopy. Band positions and intensities recorded with 0.2‐cm^?1 resolution were compared with previous gas‐phase and argon matrix isolation experiments, as well as theoretical calculations. The largest matrix shift in the absorption maximum (‐7.4 cm^?1) was observed for anthracene, with all others shifted by 3.0 cm^?1 or less. Spectral features in the supersonic jet spectrum were generally narrower than those observed in the Ar matrix, with the largest matrix broadening found for the perylene (80 % increase). Low number densities observed for the larger polycyclic aromatic hydrocarbons (PAHs) suggest that the lower vapor pressure of PAHs with catacondensed four‐membered rings and with five‐membered rings other than perylene will not be detectable using our current configuration.     

High-energy collision-induced dissociation of small polycyclic aromatic hydrocarbons

High-energy collision-induced dissociation (CID) experiments on polycyclic aromatic hydrocarbons (PAHs) having 2-6 rings, naphthalene, anthracene, phenanthrene, fluoranthene, pyrene and coronene, were performed, and the relative abundances of their fragment ions were investigated as a function of collision energy. The results revealed that the PAHs except naphthalene showed a bimodal-type distribution of positive fragmentation ions, which is closely similar to the fragment-ion distribution reported for the CID of three-dimensional fullerene, C(60)(+) and C(70)(+). The three-ring isomers of anthracene and phenanthrene and the four-ring isomers of fluoranthene and pyrene can be distinguishable in their spectra under an electron ionization energy of 70 eV, but the high-energy CID spectra of the three- and four-ring isomers were almost identical. The fragmentation corresponding to fragment ions in the low-mass region of the bimodal CID spectra could be interpreted by the simple statistical model that fragment ions are formed by random evaporation from the molecular ions after a considerable structural rearrangement, 'phase transition', occurring at some high-energy state.     

全二维气相色谱-飞行时间质谱联用技术分析重馏分油中芳烃组成

通过对升温速度、二维补偿温度、调制周期等关键实验参数的优化,建立了全二维气相色谱-飞行时间质谱(GC×GC-TOF MS)分析重馏分油中芳烃组分的方法,得到了重馏分油芳烃组分按环数分布的二维点阵图。根据谱库检索、标准化合物对照及文献报道,对重馏分油芳烃组分中菲、甲基菲及芘、苯并蒽等常见多环芳烃(PAH)进行了准确定性,并将该方法应用到重馏分油加氢处理工艺研究中,对菲、芘的加氢处理产物进行了定性分析。该研究为重馏分油芳烃组分的准确定性提供了新的技术手段,为加深对油品加氢规律的认识提供了技术支持。全二维气相色谱与普通一维色谱对比,在重馏分油的芳烃组分分析上体现了极大优势。     

Primary alkyl fluorides as regioselective alkylating reagents of lithium arene dianions. Easy prediction of regioselectivity by MO calculations on the dianion

Lithium arene dianions derived of polycyclic aromatic hydrocarbons, such as naphthalene, anthracene, phenanthrene, fluoranthene, pyrene, chrysene and binaphtyl react cleanly with n-alkylfluorides to afford regiochemically controlled alkylated dihydroarenes after hydrolysis. These arene dianions can be easily prepared by simple treatment of the arene with lithium in THP. Unlike simple radical coupling, the alkylation of these species with alkyl fluorides apparently goes through a S_N2 transition state, despite the inertness of alkyl fluorides to undergo nucleophilic substitution. It is also atypical for reduced arenes, which tend to give ET reactions with other alkyl halides. Prediction of the regiochemistry was easily conducted by means of MO calculations (PM3) on the dianion, and in all cases were consistent with the experimental.     

褐煤蜡树脂中多环芳烃组成的研究

采用气相色谱法对云南寻甸褐煤蜡树脂和吉林舒兰褐煤蜡树脂,进行了多环芳烃分布特征的研究,从树脂中鉴定出６８个化合物的同系物。两个树脂样均以菲系化合物占有优势,舒兰树脂中菲系列量约三倍于寻甸树脂的相应量     

Inhibitory analysis of the effect of polycyclic aromatic hydrocarbons on the activity of chitinase by means of liquid chromatography-mass spectrometry of chitin oligosaccharides

The analytical method of determining enzyme activity by liquid chromatography-mass spectrometry (LC/MS) was developed and applied for investigation of the effect of polycyclic aromatic hydrocarbons (PAHs) on the enzyme activity of chitinase. The measurement of chitinase activity by LC/MS is useful in order to use the nonderivatized substrate, which can show in vivo chitinase activity. Substrate consumption and product formation were monitored in order to determine chitinase activity. It was shown that, for the first time, in vitro addition of PAHs inhibited the activity of chitinase in a noncompetitive manner. The IC₅₀ value of benzo[a]pyrene was 1.4 μM, and PAHs containing four or more aromatic rings showed the same or higher inhibitory effect, whereas PAHs with a lower number of aromatic rings showed lower inhibition of the chitinase activity than benzo[a]pyrene.     

The peri effect in aromatic hydrocarbon carcinogenesis: An empirical force field examination

Methyl substitutents located peri to bay-region benzo rings of polycyclic aromatic hydrocarbons generally reduce or eliminate carcinogenic activity, most likely because such substituents force the hydroxyl groups of dihydrodiol intermediates to adopt preferentially pseudodiaxial, rather than pseudodiequatorial, conformations. Empirical force field calculations have been employed to examine the influences of peri and other positional substituents on hydroxyl conformation, taking naphthalene, anthracene, and phenanthrene as model compounds. For the unsubstituted naphthalene and anthracene dihydrodiols, the pseudodiequatorial conformation is preferred. This preference is reduced by adjacent methyl substitution and reversed by peri methyl substitution. Because of steric crowding the phenanthrene bay-region dihydrodiol preferentially adopts a pseudodiaxial conformation. The results are discussed in relation to recent experimental evidence.