邻-硝基酚分子印迹聚合物为涂层固相萃取搅拌棒的制备及其萃取性能研究

以邻-硝基酚为模板,甲基丙烯酸二甲胺乙酯和4-乙烯基吡啶为混合单体,利用整体材料"原位"聚合技术制备分子印迹聚合物为涂层的固相萃取搅拌棒(MIP-SBSE)。考察了制备条件对MIP-SBSE选择吸附性能的影响,并与高效液相色谱-二极管阵列检测器联用,探讨MIP-SBSE对环境水样中邻-硝基酚及其它酚类物质的选择萃取性能。考察了样品基底中离子强度、pH值以及吸附时间和解吸时间等萃取条件对目标化合物选择性能影响。结果表明,在最佳萃取条件下,MIP-SBSE对模板分子及其它酚类物质具有一定选择性能和较高的富集能力,对邻-硝基酚的线性范围为3.0～200μg/L;检出限LOD(S/N=3)为0.13μg/L;定量限LOQ(S/N=10)为0.40μg/L。在实际样品分析中,模板分子加标回收率为83.4%～120.9%;其它酚类物质的加标回收率在59.8%～129.0%之间。     

高效液相色谱分离牛奶中己烯雌酚、己烷雌酚和双烯雌酚

采用基质固相分散技术,对牛奶中己烯雌酚(DES)、己烷雌酚(HEX)和双烯雌酚(DS)残留进行提取和净化处理,并通过高效液相色谱进行分离。研究雌激素在C18,Florisil和N-丙基乙二胺(PSA)填料的保留行为,并研究不同流动相和色谱柱对3种雌激素的分离。实验结果表明,流动相为20 mmol/L磷酸/乙腈(42/58,V/V),流速1.0 mL/min,紫外波长230 nm。Xterra C18柱对3种雌激素分离最好。3种雌激素的平均回收率为84.1%~93.5%,相对标准偏差为3.5%~7.8%。DES、HEX和DS的检出限(LOD)分别为0.004,0.004和0.006 mg/kg,定量限(LOQ)分别为0.01、0.01和0.02 mg/kg;本方法可对样品进行灵敏、准确的定性定量分析。     

微囊藻毒素分子印迹搅拌棒涂层的研制及其吸附性能

以微囊藻毒素(MC)-LR为模板,甲基丙烯酸(MAA)为功能单体,通过可逆加成-断裂链转移(RAFT)自由基聚合技术,在凹凸棒土(ATP)表面制备了磁性分子印迹聚合物,并通过溶胶-凝胶法将分子印迹聚合物作为涂层介质制作搅拌棒。同时通过红外吸收光谱和扫描电镜等对印迹聚合物进行了结构和形貌的表征,并用液相色谱研究了搅拌棒涂层对水体中微囊藻毒素的吸附性能。结果表明,在最佳萃取条件下,分子印迹搅拌棒涂层对MC-LR具有较高的选择性能,在0.010~5.0 mg/L范围内线性关系良好(r²>0.997),检出限(S/N=3)可低至0.27 μg/L。MC-LR加标水平为20.0~80.0 μg/L的回收率范围为83.33%~100.07%,相对标准偏差(RSD)为1.40%~9.17%。该方法快速、灵敏、选择性高,可用于环境水体中微囊藻毒素的分析检测。     

环境水样中己烯雌酚与双烯雌酚的离子液体分散液-液微萃取/高效液相色谱法测定

以离子液体([Omim][PF6])为萃取剂,采用冷诱导分散液-液微萃取对环境水样中的己烯雌酚和双烯雌酚残留进行富集.优化后的萃取条件:在pH 3.0的条件下,以50 μL离子液体为萃取剂,0.8 mL甲醇为分散剂,采用反相 Extend-C18柱(5 μm, 250 mm×4.6 mm),流动相为水-甲醇(体积比40 ∶ 60),流速:1.0 mL/min,柱温:35 ℃,检测波长:245 nm.在优化的萃取条件下,己烯雌酚和双烯雌酚的线性范围均为2.5 ～200 μg/L,检出限(S/N=3)为80 ng/L.应用于环境水样中己烯雌酚和双烯雌酚的检测,加标回收率为93% ～98%,相对标准偏差为3.0% ～5.4%,建立的方法简单、环保.     

分子印迹聚合物为涂层的吸附萃取搅拌棒在环境水样双酚A含量测定中的应用

以双酚A(BPA)为单体,利用整体材料“原位”聚合技术制备以分子印迹聚合物为涂层的吸附萃取搅拌棒(MIP-SBSE),然后与高效液相色谱(HPLC)-二极管阵列检测器联用,探讨其对环境水样BPA的选择萃取性能。优化萃取过程中吸附和解吸时间、解吸液种类以及基底pH值和离子强度对目标化合物的选择吸附性能。在最佳条件下,MIP-SBSE可对模板分子进行有效的选择吸附,线性范围为1.0～200 μg/L,检出限(S/N=3)和定量限(S/N=10)分别为0.28μg/L和0.94 μg/L。在实际水样分析中,具有良好的加标回收率,其值为96.0%～108.7%。研究结果表明,所建立的方法具有简便、灵敏和环境友好等特点。     

己烷雌酚分子印迹介孔硅的制备及识别机制

本文基于半共价印迹技术,采用热可逆共价键构键分子识别位点,预先合成共价键合的己烷雌酚印迹前体物,再采用溶胶-凝胶法制备出己烷雌酚纳米分子印迹介孔硅材料。通过扫描电镜和X射线衍射确认了分子印迹介孔硅的有序结构。红外光谱和13C核磁共振波谱研究表明,介孔硅表面和内部均存在可与印迹分子相互作用的官能团。     

基于溶胶凝胶技术的在线固相萃取与高效液相色谱联用测定饮用水中的雌激素残留

建立了固相萃取与高效液相色谱在线联用测定水样中3种雌激素(己烯雌酚、己烷雌酚、双烯雌酚)痕量残留的方法。以溶胶凝胶技术合成的聚合物为固相萃取材料,对水样中的雌激素进行萃取富集,考察了样品溶液不同pH、上样流速及洗脱溶剂等条件对合成材料富集效果的影响。结果表明,在优化的条件下,该方法对3种雌激素的检出限(S/N=3)为0.07~0.13 μg/L,样品中的加标回收率为82.31%~99.43%,相对标准偏差(RSD)为1.61%~7.15%。方法简便可靠,适用于饮用水中雌激素的痕量残留检测。     

应用分子印迹磁性搅拌棒/高效液相色谱检测鱼饲料中的孔雀石绿

采用二步包裹修饰后的高磁性超顺材料钕铁硼磁粉作为磁性供体,以孔雀石绿(MG)为模板,α-甲基丙烯酸(MAA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,利用原位聚合法制备了新型整体式分子印迹吸附萃取搅拌棒(MIP-SBSE),并与高效液相色谱(HPLC)联用测定鱼饲料中的孔雀石绿。考察了吸附和解吸时间、pH值和盐浓度对目标化合物萃取性能的影响。结果表明:在最优条件下,MIP-SBSE可对模板分子进行有效的选择性吸附,线性范围为10~500μg/L;检出限为103~215 ng/L,用该方法对鱼饲料中的孔雀石绿进行分析测定,测得加标回收率为87.3%~94.1%。     

罗丹明B分子印迹固相萃取小柱的研制及应用

研制一种对罗丹明B具有特异性识别性能的分子印迹固相萃取小柱。用沉淀聚合法制备罗丹明B分子印迹聚合物,通过静态平衡吸附实验及固相萃取实验表征其性能,并对市售辣椒样品中的罗丹明B进行测量。罗丹明B模板聚合物的吸附能力明显优于空白聚合物;印迹固相萃取小柱对罗丹明B标准溶液(0.05 mmol/L)一次性萃取率为98.24%,实际样品测量的回收率为90.0%~95.0%,测定结果的相对标准偏差为0.9%~1.7%(n=3)。罗丹明B分子印迹固相萃取小柱选择性好、萃取率高,可应用于食品、化妆品检测等相关领域。     

尼龙6纳米纤维膜的制备及其对己烷雌酚的吸附性能研究

采用静电纺丝设备制备尼龙6纳米纤维膜。用静、动态吸附方法,研究了尼龙6纳米纤维膜对己烷雌酚的吸附性能,考察了吸附时间、初始浓度及介质p H值对尼龙6纳米纤维膜吸附己烷雌酚的影响。结果表明,初始浓度为2mg/L时,尼龙6纳米纤维膜吸附己烷雌酚的过程符合准一级动力学模型;当初始浓度在5~20mg/L范围内,吸附过程符合准二级动力学模型。尼龙6纳米纤维膜吸附己烷雌酚的过程符合Freundlich等温吸附模型。     

Development of selective and chemically stable coating for stir bar sorptive extraction by molecularly imprinted technique

A novel stir bar coated with molecularly imprinted polymer (MIP) as selective extraction phase for sorptive extraction of triazine herbicides was developed. The stir bar was prepared by chemically bonding the MIP to the glass bar to improve its stability. A homogeneous and porous structure was observed on the stir bar surface. Extraction performance shows that the MIP-coated stir bar has stronger affinity to the template molecule terbuthylazine as compared with that of the reference stir bar without addition of template. Owning to the shape and structural compatibility, the obtained stir bar also demonstrated specific selectivity to the structural related-compounds of nine triazines, and thus can be applied to simultaneous determination of these compounds from complex samples coupled with high performance liquid chromatography. Four complex samples with different matrix, including rice, apple, lettuce and soil were used to evaluate this proposed method. The limits of detection obtained are in the range of 0.04-0.12 μg L⁻¹, and the recoveries for the spiked rice, apple, lettuce and soil samples were 80.8-107.7%, 80.6-107.8%, 72.0-109.8% and 89.0-114.8% with RSD from 1.2 to 7.9%, respectively. Moreover, this MIP-coated stir bar was firm, durable and can be prepared simply and reproducibly. The developed coating method would be useful to prepare a range of selective stir bars in order to extend the applicability of stir bar sorptive extraction (SBSE) in complex sample analysis.     

Preparation of a molecularly imprinted polymer for the solid-phase extraction of scopolamine with hyoscyamine as a dummy template molecule

Molecularly imprinted polymers (MIPs) selective for scopolamine were produced using hyoscyamine (a close structural analogue) as template molecule. The produced polymers were used as media for solid-phase extraction, exhibiting selective binding properties for the analyte from biological samples. Human and calf urine and serum were processed on the MIP under various extraction protocols. The best performance was observed after loading the analyte in aqueous environment facilitating retention on the MIP by non-selective hydrophobic interactions. The MIPs were subsequently washed using an optimised solvent system to enable selective desorption of the analyte. Other related and non-related compounds were accessed to evaluate molecular recognition properties. Recoveries of up to 79% were achieved for the analyte of interest from biological samples.     

Preparation and evaluation of molecularly imprinted solid-phase microextraction fibers for selective extraction of bisphenol A in complex samples

Molecular imprinted polymer (MIP) as solid-phase microextraction (SPME) fibers coating has gained great attention in recent years. In this study, a simple preparation approach for bisphenol A (BPA) MIP coating with controlled thickness on fused-silica capillaries was developed. A capillary was inserted into a larger bore capillary to form a sleeve as mold. The prepolymer solution containing the template BPA was introduced into the interspace between the two capillaries for polymerization under photoirradiation. The larger bore capillary was removed away after the polymerization, and MIP coating with certain thickness on the surface of the inserted capillary was obtained. SPME conditions based on the MIP-coated fibers were optimized, and the extraction performance of the fibers with different thickness coating was compared. Finally, the MIP fibers were used for selective extraction of BPA spiked in tap water, human urine, and milk samples. The average recoveries of spiked BPA in the three samples were 92.5%, 81.6%, and 87.5%, respectively. The present analytical performance is not up to par for applicability to real environmental matrices. Further improvement will be necessary for analysis of real complex samples.     

Molecularly imprinted polymer with high-fidelity binding sites for the selective extraction of barbiturates from human urine

In this paper we describe the synthesis of a molecularly imprinted polymer (MIP) by precipitation polymerisation, with barbital as the template molecule, and the application of the barbital MIP as a molecularly selective sorbent in the solid-phase extraction (SPE) of barbiturates from human urine samples. The MIP was synthesised by precipitation polymerisation using 2,6-bis-acrylamidopyridine as the functional monomer and DVB-80 as the cross-linking agent. The spherical MIP particles produced were 4.2 ± 0.4 μm in diameter; a non-imprinted control polymer (NIP) in bead form was 4.8 ± 0.4 μm (mean±standard deviation) in diameter. The particles were packed into a solid-phase extraction cartridge and employed as a novel sorbent in a molecularly imprinted solid-phase extraction (MISPE) protocol. The MIP showed high selectivity for the template molecule, barbital, a feature which can be ascribed to the high-fidelity binding sites present in the MIP which arose from the use of 2,6-bis-acrylamidopyridine as the functional monomer. However, the MIP also displayed useful cross-selectivity for other barbiturates besides barbital. For real samples, the MIP was applied for the extraction of four barbiturates from human urine. However, due to the high urea concentration in this sample which interfere the proper interaction of barbiturates onto the MIP, a tandem system using a commercially available sorbent was developed.     

Molecular-imprinted polymer extraction combined with dispersive liquid-liquid micro-extractionfor ultra-preconcentration of mononitrotoluene

Molecular-imprinted polymer (MIP) combined with dispersive liquid-liquid micro-extraction (DLLME) were developed for ultra-preconcentration and determination of mononitrotoluenes in wastewater samples using gas chromatography-flame ionization detector. MIP was synthesized by copolymerization of methacrylic acid-ethylene glycole dimethacrylate-2,2-azobisisobutyronitrile as the initiator that imprinted with 3-nitrotoluene as the template molecule. Effects of several factors, such as type and volume of eluent, adsorption, and desorption times of the analyte on the polymer, and breakthrough volume were investigated. Optimization of 3-nitrotoluene extraction from MIP was studied forward followed by DLLME. Preconcentration factor of MIP-DLLME method was about 2800 under the optimum conditions. The LOD of the proposed method was 0.02?μg/L and a linear dynamic range in the range of 0.04-20?μg/L was obtained. The performance of the present method was evaluated for extraction and determination of nitrotoluene compounds in wastewater samples in the range of microgram per liter and satisfactory results were achieved (RSD<13%).     

Molecularly imprinted stir bar sorptive extraction coupled with high performance liquid chromatography for trace analysis of sulfa drugs in complex samples

A novel sulfamethazine molecularly imprinted polymer (MIP)-coated stir bar for sorptive extraction of eight sulfa drugs from biological samples was prepared. The MIP-coating was about 20 μm thickness with the relative standard deviation (RSD) of 6.7% (n = 10). It was characterized by scanning electron microscope, infrared spectrum, thermogravimetric analysis, and solvent-resistant investigation, respectively. The non-imprinted polymer (NIP)-coating was used for comparison. The adsorptive capacity and selectivity of MIP-coating were evaluated in detail. The MIP-coating showed higher adsorption capability and selectivity than the NIP-coating. The saturated adsorption amount of the MIP-coating was 4.6 times over that of the NIP-coating in toluene. Sulfamethazine could be detected after the MIP-coated stir bar sorptive extraction even at a low concentration of 0.2 μg/L. The MIP-coating also exhibited selective adsorption ability to analogues of the template. A method for the determination of eight sulfa drugs in biological samples by MIP coated stir bar sorptive extraction coupled with high performance liquid chromatography (HPLC) was developed. The extraction conditions, including extraction solvent, extraction time, desorption solvent, desorption time and stirring speed, were optimized. The linear ranges were 1.0-100 μg/L and 2.0-100 μg/L for eight sulfonamides, respectively. The detection limits were within the range of 0.20-0.72 μg/L. The method was successfully applied to simultaneous multi-residue analysis of eight sulfonamides in spiked pork, liver and chicken samples with the satisfactory recoveries.     

Development of andrographolide molecularly imprinted polymer for solid-phase extraction

A method employing molecularly imprinted polymer (MIP) as selective sorbent for solid-phase extraction (SPE) to pretreat samples was developed. The polymers were prepared by precipitation polymerization with andrographolide as template molecule. The structure of MIP was characterized and its static adsorption capacity was measured by the Scatchard equation. In comparison with C(18)-SPE and non-imprinted polymer (NIP) SPE column, MIP-SPE column displays high selectivity and good affinity for andrographolide and dehydroandrographolide for extract of herb Andrographis paniculata (Burm.f.) Nees (APN). MIP-SPE column capacity was 11.9±0.6 μmol/g and 12.1±0.5 μmol/g for andrographolide and dehydroandrographolide, respectively and was 2-3 times higher than that of other two columns. The precision and accuracy of the method developed were satisfactory with recoveries between 96.4% and 103.8% (RSD 3.1-4.3%, n=5) and 96.0% and 104.2% (RSD 2.9-3.7%, n=5) for andrographolide and dehydroandrographolide, respectively. Various real samples were employed to confirm the feasibility of method. This developed method demonstrates the potential of molecularly imprinted solid phase extraction for rapid, selective, and effective sample pretreatment.     

Fabrication of the Monolithic Fiber for the Solid Phase Micro‐extraction of Malachite Green

A monolithic fiber of molecularly imprinted polymer (MIP) was prepared by in situ polymerization within the capillary with an inner diameter of 530 µm. It was carried out in 8 min by microwave irradiation using malachite green (MG) as a template molecule, α‐methacrylic acid (MAA) as a functional monomer, acetonitrile (ACN) as a porogenic solvent, ethylene dimethacrylate (EDMA) as a crosslinker, azodiiso‐butyronitrile (AIBN) as a thermal initiator. The resulted MIP fibers were pushed out from the capillary, eluted and inserted in the capillary again, which successfully used for the solid phase microextraction (SPME) procedure. The factors affecting the extraction of MG, such as the molar ratio of template/monomer (MG/MAA), concentration of NaCl, extraction and desorption time, and extraction and desorption solvents were investigated in detail. The selectivity of the MIP fibers was compared using MG analogues crystal violet (CV) and non‐analogue Sudan II. It was also employed for the pretreatment of trace MG in the fish feed followed by high‐performance liquid chromatography (HPLC) detection. Under the optimal conditions, the linear range of MG was 10‐600 μg/L, the detection limit (LOD) was 1.23 μg/L and the recovery of spiked fish feed sample was 88.7～113.9%.     

Selective Solid‐phase Extraction of Bisphenol A Using a Novel Stir Bar Based on Molecularly Imprinted Monolithic Material

In this paper, a novel monolithic stir bar based on molecularly imprinted polymer (MIP) was firstly developed by filling modified neodymium magnet (Nd₂Fe₁₄B) powders into a glass tube (60 × 4 mm), followed by the imprinted grafting with bisphenol A (BPA) as the template molecule by thermal polymerization. It has been successfully used for the stir bar sorptive extraction (SBSE) and its extraction performance illustrated that the MIP‐encapsulated stir bar had stronger affinity to the template molecule, compared with the stir bar based on the non‐imprinted molecularly polymer (NIP). Under the optimal extraction conditions, a simple method based on the coupling of MIP‐SBSE with high performance liquid chromatography (HPLC) was used for the selective determination of the model mixtures of BPA, 4‐phenylphenol (PP) and phenol (P) in bottled water. The recoveries of BPA, PP and P were in the range of 88.5‐96.1%, 78.2‐89.7%, 81.3‐89.5% at three spiked levels, respectively, demonstrating that higher extraction and the specific absorption occurred between the template molecule and the prepared MIP stir bar.