Competitive Adsorption of Methylene Blue and Rhodamine B on Natural Zeolite: Thermodynamic and Kinetic Studies

A batch system was applied to study the adsorption behavior of methylene blue (MB) and rhodamine B (RB) in single and binary component systems on natural zeolite. In the single component systems, the zeolite presents higher adsorption capacity for MB than RB with the maximal adsorption capacity of 7.95×10^?5 and 1.26×10^?5 mol/g at 55°C for MB and RB, respectively. Kinetic studies indicated that the adsorption followed pseudo‐second‐ order kinetics and could be described by a two‐step diffusion process. For the single component systems, the adsorption isotherm could be fitted by the Langmuir model. In the binary component system, MB and RB exhibit competitive adsorption on the zeolite. The adsorption is approximately reduced to 50% and 60% of single component adsorption systems of MB and RB, respectively at an initial concentration of 6×10^?6 mol·L^?1 at 25°C. In the binary component system, kinetic and adsorption isotherm studies demonstrate that the experimental data are following pseudo‐second‐order kinetics and Langmuir isotherm and kinetic data are fairly described by a two‐step diffusion model. Effect of solution pH on adsorption of MB and RB in both single and binary component systems was studied and the results were described by electrostatic interactions.     

Efficient removal of MB dye using litchi leaves powder adsorbent: Isotherm and kinetic studies

Removal of Methylene Blue (MB) dye using Litchi Leaves Powder (LLP) material was carried out in batch mode. Effect of the mass of the adsorbent (0.1–2.5 g/L), pH of the solution (2−12), starting concentration of MB dye (50–150 mg/L), ionic strength using NaCl (0.1–0.5 M) as an electrolyte, contact time (0–60 min) on the adsorption of MB dye was studied. To calculate pH at which LLP material surface becomes neutral point of zero charge (pH_pzc) is also determined and found to be 6.48. Removal process best fit in the pseudo-second-order kinetic model as indicated by its higher R² value (0.999). Isotherm models (Freundlich and Langmuir) were fitted to the data obtained from the experiment to understand the adsorption behaviour. Result shows that experimental data were fitted to the both isotherm models (Freundlich and Langmuir) as indicated by higher R² value for both Freundlich (0.991) and Langmuir (0.994) model, and it was determined that LLP has a maximum adsorption capacity of 119.76 mg/g.     

Enhanced adsorption performance of a novel Fe‐Mn‐Zr metal oxide nanocomposite adsorbent for anionic dyes from binary dye mix: Response surface optimization and neural network modeling

A novel adsorbent, Fe‐Mn‐Zr metal oxide nanocomposite was synthesized and investigated for removal of methyl orange (MO) and eosin yellow (EY) dyes from binary dye solution. The magnetic nanocomposite has shown surface area of 143.01 m²/g and saturation magnetization of 15.29 emu/g. Optimization was carried out via response surface methodology (RSM) for optimizing process variables, and optimum dye removal of 99.26% and 99.55% were obtained for MO and EY dye, respectively with contact time 62 min, adsorbent dose 0.45 g/l, initial MO concentration 11.0 mg/l, and initial EY concentration 25.0 mg/l. A feed forward back propagation neural network model has shown better prediction ability than RSM model for predicting MO and EY dye removal (%). Adsorption process strictly follows Langmuir isotherm model, and enhanced adsorption capacities of 196.07 and 175.43 mg/g were observed for MO and EY dye, respectively due to synergistic effects of physicochemical properties of trimetal oxides. Surface adsorption and pore diffusions are the mechanisms involved in the adsorption as revealed from kinetic studies.     

Preparation of MnO2 Loaded Hydrothermal Carbon-coated Electrospun PAN Fiber Membranes for Highly Efficient Adsorption and Separation of Cationic Dye

Hydrothermal carbonaceous materials and MnO₂ have been proved to be promising adsorbents to remove organic dyes from wastewater. In this study, flexible MnO₂ loaded hydrothermal carbon-coated electrospun poly-acrylonitrile(AC/MnO₂/PAN) fiber membranes were fabricated by a facile one-step hydrothermal method and activated by NaOH solution. The composite fibers exhibited large adsorption capacity toward cationic dyes and excellent mechanical properties. The adsorption performance can be fitted well with pseudo-second-order model and Langmuir isotherm model. The maximum adsorption for methylene blue(MB), methyl violet(MV) and malachite green(MG) are 1173.27,1106.31 and 1129.89 mg/g, respectively, according to Langmuir fitting. The AC/MnO₂/PAN fiber membrane also showed satisfactory performances for selective adsorption and recyclability. In addition, based on selective adsorption, the AC/MnO₂/PAN fiber membranes that are repulsive to the anionic dye methyl orange(MO) can separate the MB/MO mixture solution by dynamic filtration. Thus, this work not only provides a facile strategy to fabricate large capacity adsorbents, but also demonstrates the potential applications in the dye wastewater treatment field.     

具有染料选择吸附性的衍生于沸石咪唑酯骨架-67的NiCo-层状双氢氧化物设计与合成

以沸石咪唑类金属有机骨架(ZIF-67)为模板合成了一种新型的中空吸附剂NiCo-LDH@ZIF-67,该吸附剂对甲基橙具有良好的选择吸附性以及可循环性。 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线粉末衍射仪(XRD)、红外光谱、电子能谱和氮气吸附-脱附等手段对样品进行了表征。 研究了溶液的pH值、甲基橙的初始浓度以及染料与吸附剂作用时间对NiCo-LDH@ZIF-67吸附性能的影响。 结果表明,该吸附剂对甲基橙的吸附动力学符合准二级动力学模型,且吸附等温线符合朗缪尔方程。 当pH值等于4, 吸附时间15 min,吸附剂用量为2400 mg/L时,该吸附剂对甲基橙的最大吸附量可达1766 mg/g,高于之前文献报道的类似吸附剂。 此外,NiCo-LDH@ZIF-67能从甲基橙和亚甲基蓝的混合溶液中选择性吸附甲基橙。     

Ultrasound-aided rapid and enhanced adsorption of anionic dyes from binary dye matrix onto novel hematite/polyaniline nanocomposite: Response surface methodology optimization

In recent times, polyaniline (PANI), a conducting polymer, has been studied widely for environmental remediation application due to its controllable electric conductivity with high surface area, which makes it a suitable adsorbent material. But lower mechanical stability of PANI is considered to be a serious drawback for its large-scale industrial application. To improve the mechanical strength of PANI, in this study, hematite nanoparticles were impregnated onto PANI by oxidative polymerization method in order to fabricate a novel organometallic nanocomposite (hematite-PANI-NC). The hematite-PANI-NC was used as adsorbent for removal of methyl orange (MO) and eosin yellow (EY) dye from binary dye matrix under ultrasonic-assisted adsorption. Excellent MO and EY dye removal (more than 98%) was observed from binary matrix at a wide solution pH from 2.0 to 6.0, and under ultrasound wave the adsorption equilibrium was achieved within 15 min only. Both MO and EY dyes adsorption experimental data strictly followed Langmuir isotherm, and maximum monolayer adsorption capacity of 126.58 mg/g and 112.36 mg/g was observed for MO and EY dye, respectively. The uptake mechanism of MO and EY dyes onto hematite-PANI-NC is governed by electrostatic interaction, π-π bonding and hydrogen bonding between dye molecules and nanocomposite. Response surface methodology analysis reveals maximum MO and EY removal of 98.43% and 99.35% at optimum experimental conditions. This study implies that the hybrid organometallic material hematite-PANI-NC has high potential for quick and enhanced sono-assisted uptake of anionic dyes from water near neutral solution pH.     

The Use of High Surface Area Mesoporous-Activated Carbon from Longan Seed Biomass for Increasing Capacity and Kinetics of Methylene Blue Adsorption from Aqueous Solution

Microporous- and mesoporous-activated carbons were produced from longan seed biomass through physical activation with CO₂ under the same activation conditions of time and temperature. The specially prepared mesoporous carbon showed the maximum porous properties with the specific surface area of 1773 m²/g and mesopore volume of 0.474 cm³/g which accounts for 44.1% of the total pore volume. These activated carbons were utilized as porous adsorbents for the removal of methylene blue (MB) from an aqueous solution and their effectiveness was evaluated for both the adsorption kinetics and capacity. The adsorption kinetic data of MB were analyzed by the pseudo-first-order model, the pseudo-second-order model, and the pore-diffusion model equations. It was found that the adsorption kinetic behavior for all carbons tested was best described by the pseudo-second-order model. The effective pore diffusivity (D_e) derived from the pore-diffusion model had the values of 4.657 × 10⁻⁷–6.014 × 10⁻⁷ cm²/s and 4.668 × 10⁻⁷–19.920 × 10⁻⁷ cm²/s for the microporous- and mesoporous-activated carbons, respectively. Three well-known adsorption models, namely the Langmuir, Freundlich and Redlich–Peterson equations were tested with the experimental MB adsorption isotherms, and the results showed that the Redlich–Peterson model provided the overall best fitting of the isotherm data. In addition, the maximum capacity for MB adsorption of 1000 mg/g was achieved with the mesoporous carbon having the largest surface area and pore volume. The initial pH of MB solution had virtually no effect on the adsorption capacity and removal efficiency of the methylene blue dye. Increasing temperature over the range from 35 to 55 °C increased the adsorption of methylene blue, presumably caused by the increase in the diffusion rate of methylene blue to the adsorption sites that could promote the interaction frequency between the adsorbent surface and the adsorbate molecules. Overall, the high surface area mesoporous carbon was superior to the microporous carbon in view of the adsorption kinetics and capacity, when both carbons were used for the removal of MB from an aqueous solution.     

Adsorptive performance of MWCNTs for simultaneous cationic and anionic dyes removal; kinetics,thermodynamics, and isotherm study

Disposal of contaminated wastewater causes many serious problems especially when it gets mixed with the ground and seawater. It is, therefore, important to apply any remedial action to eradicate dangerous pollutants from the aqueous effluents and to avoid exposure of this wastewater to aquatic life. The research results discussed herein deal with the removal of Rhodamine B (RhB) and Congo Red (CR) dye from wastewater by using multi-walled carbon nanotubes (MWCNTs) as an adsorbent. Different factors like solid dosage, initial pH and concentration, time, and temperature were studied to understand the behavior and mechanism of adsorption. The maximum adsorption capacity in case of a single component system was found to be 302 mg/g and 300 mg/g for Congo Red and Rhodamine B, respectively. Moreover, the mechanism of adsorption was best described by a pseudo-second-order kinetic model. Thermodynamic parameters showed that adsorption of CR and RhB was exothermic when these were removed from a single dye system. However, the overall process became endothermic for concurrent removal of both dyes from the solution. The research results showed that the MWCNTs could successfully be utilized to remove the dye from the industrial wastewater.     

Selective and effective adsorption of methyl blue by barium phosphate nano-flake

We report the synthesis of barium phosphate (BP) nano-flake and its adsorption behavior to methyl blue (MB) in aqueous solution. The as-obtained BP nano-flake revealed pure rhombohedral crystal structure. The adsorption capacity of MB onto BP reached 1500mgg(-1). The adsorption equilibrium results fitted well with the Freundlich isotherm model. The adsorption process took less than 30min to reach equilibrium. The adsorption kinetics was elucidated by the pseudo-second-order kinetic equation. It followed 2-stage and 3-stage intra-particle diffusion models for the low and high concentration of dye solutions, respectively. The adsorption of MB using the BP nano-flake was highly selective, compared with the adsorption of other dyes. The interactions between MB and BP were mainly the ionic interaction and hydrogen bonds, which were confirmed by the X-ray photoelectron spectroscopic results and the density functional theory calculations. The BP nano-flake revealed less than 5% decrease in adsorption amount when it was recycled and reused five times. The present work shows that the BP nano-flake is promising for practical applications in MB removal from aqueous solutions.     

Mixed phase Fe2O3/Mn3O4 magnetic nanocomposite for enhanced adsorption of methyl orange dye: Neural network modeling and response surface methodology optimization

In this research, a novel magnetic mesoporous adsorbent with mixed phase of Fe₂O₃/Mn₃O₄ nanocomposite was prepared by a facile precipitating method and characterized extensively. The prepared nanocomposite was used as adsorbent for toxic methyl orange (MO) dye removal from aqua matrix considering its high surface area (178.27 m²/g) with high saturation magnetization (23.07 emu/g). Maximum dye adsorption occurs at solution pH 2.0 and the electrostatic attraction between anionic form of MO dye molecules and the positively charged nanocomposite surface is the main driving force behind this adsorption. Response surface methodology (RSM) was used for optimizing the process variables and maximum MO removal of 97.67% is obtained at optimum experimental condition with contact time, adsorbent dose and initial MO dye concentration of 45 min, 0.87 g/l and 116 mg/l, respectively. Artificial neural network (ANN) model with optimum topology of 3–5–1 was developed for predicting the MO removal (%), which has shown higher predictive ability than RSM model. Maximum adsorption capacity of this nanocomposite was found to be 322.58 mg/g from Langmuir isotherm model. Kinetic studies reveal the applicability of second‐order kinetic model with contribution of intra‐particle diffusion in this process.     

Adsorption of methylene blue dye from aqueous solution by agricultural waste: Equilibrium,thermodynamics, kinetics,mechanism and process design

The adsorption of methylene blue (MB) dye from aqueous solution onto a cashew nut shell (CNS) was investigated as a function of parameters such as solution pH, CNS dose, contact time, initial MB dye concentration and temperature. The CNS was shown to be effective for the quantitative removal of MB dye, and the equilibrium was reached in 60 min. The experimental data were analysed by two-parameter isotherms (Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models) using nonlinear regression analysis. The characteristic parameters for each isotherm and the related correlation coefficients were determined. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were also evaluated, the sorption process was found to be spontaneous and exothermic. Pseudo-first-order, pseudo-second-order and Elovich kinetic models were used to analyze the adsorption process. The results of the kinetic study suggest that the adsorption of MB dye matches the pseudo-second-order equation, suggesting that the adsorption process is presumably chemisorption. The adsorption process was found to be controlled by both surface and pore diffusion. Analysis of adsorption data using a Boyd kinetic plot confirmed that the external mass transfer is a rate determining step in the sorption process. A single-stage batch adsorber was designed for different CNS doses to effluent volume ratios using the Freundlich equation. The results indicated that the CNS could be used effectively to adsorb MB dye from aqueous solutions.     

Characterization and Mechanism Elucidation of Dye Adsorption Using Cuprous Selenide Nanoparticles from Aqueous Solutions

The removal of cationic dyes, methylene blue(MB) and rhodamine B(RB), and anionic dyes, methyl or-ange(MO) and eosin Y(EY), from aqueous solutions by adsorption using Cu₂Se nanoparticles(Cu₂SeNPs) was studied. The effects of the initial pH values, adsorbent doses, contact time, initial dye concentrations, salt concentrations, and operation temperatures on the adsorption capacities were investigated. The adsorption process was better fitted the Langmuir equation and pseudo-second-order kinetic model, and was spontaneous and endothermic as well. The adsorption mechanism was probably based on the electrostatic interactions and π-π interactions between Cu₂SeNPs and dyes. For an adsorbent of 0.4 g/L of Cu₂SeNPs, the adsorption capacities of 23.1(MB), 22.9(RB) and 23.9(EY) mg/g were achieved, respectively, with an initial dye concentration of 10 mg/g(pH=8 for MB and pH=4 for RB and EY) and a contact time of 120 min. The removal rate of MB was still 70.4% for Cu₂SeNPs being reused in the 5th cycle. Furthermore, the recycled Cu₂SeNPs produced from selenium nanoparticles adsorbing copper were also an effective adsorbent for the removal of dyes. Cu₂SeNPs showed great potential as a new adsorbent for dyes removal due to its good stability, functionalization and reusability.     

Cationic dye adsorption by poly(N-isopropylacrylamide/maleic acid) copolymeric hydrogels prepared by gamma rays

N-isopropylacrylamide/maleic acid hydrogels containing different quantities of maleic acid have been synthesized with γ-radiation. The hydrogels were used in experiments on swelling, diffusion and adsorption of a cationic dye methylene blue. The diffusion of MB into the hydrogels was found to be the non-Fickian type. The factors influencing adsorption capacity of the hydrogel such as gel composition, and irradiation dose were systematically investigated. The equilibrium data for dye adsorption was better described by the Freundlich isotherm than Langmuir isotherm model. The kinetic studies showed that the pseudo-second-order kinetic model fits better than the data obtained from pseudo-first-order model.     

三聚氰胺功能化多孔有机聚合物的合成及其对甲基橙的吸附性能

首先以对三联苯(TP)和对苯二甲酰氯(TC)为单体合成了酮基聚合物前体(TP-TC),而后基于席夫碱反应将三聚氰胺(MA)与之交联得到胺功能化的多孔有机聚合物TP-TC-MA。通过扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外光谱(FT-IR)、X射线衍射(XRD)、氮气吸附-脱附(BET)以及零电荷点(pH_pzc)的测定等手段对合成的多孔有机聚合物进行表征。以染料废水中典型的阴离子染料甲基橙为研究对象,研究了TP-TC-MA对其吸附行为,并探讨了吸附机制。利用紫外-可见分光光度计(UV-Vis)得出目标污染物的紫外吸收光谱标准曲线,标准曲线拟合相关系数(R²)为0.999。结果表明,TP-TC-MA由于具有高比表面积(708.5 m²/g)和总孔体积(0.556 cm³/g)以及丰富的含氮基团,对阴离子染料甲基橙表现出优异的吸附性能。TP-TC-MA对水中甲基橙的吸附动力学符合准二级动力学方程,吸附平衡数据可以采用Langmuir等温吸附模型描述。经由Langmuir等温吸附模型计算得到的理论最大吸附容量为156.3 mg/g。选择性实验结果表明,TP-TC-MA对阴离子染料甲基橙具有更强的吸附作用,吸附作用机理可归结为静电相互作用、氢键和π-π相互作用等。在重复使用5次之后,TP-TC-MA对甲基橙仍保持90%以上的去除率,表明材料具有良好的稳定性和重复利用性,在染料废水处理中具有很好的应用前景。     

Multi‐responses optimization of simultaneous adsorption of methylene blue and malachite green dyes in binary aqueous system onto Ni:FeO(OH)‐NWs‐AC using experimental design: derivative spectrophotometry method

In this research, response surface methodology (RSM) approach using Central Composite Design (CCD) coupled by derivative spectrophotometry method was applied to develop mathematical model and optimize process parameters for simultaneous adsorption of methylene blue (MB) and malachite green (MG) from aqueous solution using Ni:FeO(OH) ‐ NWs‐AC. The optimal conditions to adsorption of MB and MG in binary mixture solution from aqueous solution were found at pH 8.0, MB concentration 20 mg L^‐1, MG concentration 20 mg L^‐1, adsorbent dosage 0.033 g and contact time 40 min. At these conditions, high adsorption efficiency (99.39% and 100.0% for MB and MG, respectively) was achieved. Among experimental equilibrium, Langmuir isotherm model fitted well with maximum monolayer adsorption capacity of 28.6 and 29.8 mg g^‐1 for MB and MG, respectively. The adsorption kinetic data followed pseudo second‐order kinetics for MB and MG dyes.     

Preparation of biomass-derived phosphorus-doped microporous carbon material and its application in dye adsorption and CO2 capture

Microporous P-doped carbon materials are synthesized by a pyrolysis method using MCM-22 as a template, sucrose as a precursor, and phosphoric acid as phosphorus sources. The results show that the pore structure of the carbon materials can be adjusted by changing the amount of phosphoric acid and template. When the P/C molar ratio is 0.075, the obtained P-doped microporous carbon material shows excellent specific surface area up to 621 m²/g and shows a high adsorption capacity of 199.40 mg/g for crystal violet dye, with a removal rate of 98.9%. When testing the CO₂ adsorption capacity, it was found that the maximum adsorption capacity reached 63 mg/g and remained stable after 10 adsorption and desorption cycles, with excellent cycle stability. The adsorption obeys pseudo-second-order kinetic model, and the adsorption isotherm follows the Langmuir model.     

Polypyrrole-coated cotton textile as adsorbent of methylene blue dye

Pollution caused by organic dyes is of serious environmental and health concern to the population. Dyes are widely used in textile coloring applications. In the present work, cotton textile was coated with a conducting polymer, polypyrrole (PPy), in situ during the oxidative polymerization of pyrrole. The resulting materials were utilized as easily separated and recyclable adsorbent for the removal of methylene blue (MB) as a model of cationic dyes in alkaline solutions. It showed also some affinity to remove Acid Green 25 as an anionic dye in acidic medium. The adsorption was assessed by monitoring the decrease in dye concentration by UV–Visible absorption spectroscopy. The influence of various parameters such as initial dye concentration, contact time, pH, temperature, and adsorbent dose on the adsorption process was studied. The pseudo-second-order kinetic model and Freundlich isotherm model were found to describe the adsorption process. The thermodynamic study revealed that the adsorption of MB by PPy was feasible, spontaneous, and exothermic process. Investigation of the substrate regeneration revealed that PPy deposited on cotton textile can be reused for dye adsorption several times with good efficiency and it allows for the recovery of MB for recycling purposes.     

Anchoring H3PW12O40 on aminopropylsilanized spinel‐type cobalt oxide (Co3O4‐SiPrNH2/H3PW12O40): A novel nanohybrid adsorbent for removing cationic organic dye pollutants from aqueous solutions

In this work, phosphotungstic acid (H₃PW₁₂O₄₀; PW₁₂) was chemically anchored on aminopropylsiloxane functionalized spherical Co₃O₄ nanoparticles (Co₃O₄–SiPrNH₂) and the resultant nanocomposite (Co₃O₄–SiPrNH₂/PW₁₂) was fully characterized. The results demonstrated successful anchoring of PW₁₂ on the surface of Co₃O₄–SiPrNH₂nanoparticles. The Co₃O₄–SiPrNH₂/PW₁₂ nanohybrid indicated a specific surface area of 42.14 m² g^?1, which was greater than that of pure PW₁₂ (ca. 5 m² g^?1). The adsorption efficiency of this novel adsorbent nanomaterial was evaluated for removing methylene blue (MB), rhodamine B (RhB) and methyl orange (MO) dyes from aqueous solutions. The hybrid nanomaterial exhibited a high adsorption rate and selective adsorptivity for the cationic MB and RhB dyes compared to those for anionic MO dye. The prepared hybrid nanomaterial removed over 98% of MB within 12 min. The effects of initial pH, contact time, adsorbent dosage, and temperature were investigated on the adsorption process. The adsorption capacity of nanohybrid for cationic MB dye was 38.46 mg g^‐1. Also, adsorption kinetics indicated that the adsorption by Co₃O₄–SiPrNH₂/PW₁₂ was well‐modeled using pseudo‐second‐order kinetic model. Finally, thermodynamic parameters revealed that the adsorption was endothermic and spontaneous. The adsorption rate and ability of the Co₃O₄–SiPrNH₂/PW₁₂ were enhanced as compared with Co₃O₄ and Co₃O₄–SiPrNH₂ samples due to enhanced electrostatic attraction intraction. The nanohybride was easily separated and reused without any change in structure. Thus, it could be a promising green adsorbent for removing organic pollutants in water.     

Treatment of methyl orange by calcined layered double hydroxides in aqueous solution: adsorption property and kinetic studies

Adsorption of a weak acid dye, methyl orange (MO) by calcined layered double hydroxides (LDO) with Zn/Al molar ratio of 3:1 was investigated. In the light of so called "memory effect," LDO was found to recover their original layered structure in the presence of appropriate anions, after adsorption part of MO(-) and CO(2-)(3) (come from air) intercalated into the interlayer of LDH which had been supported by XRD and ICP. The results of adsorption experiments indicate that the maximum capacity of MO at equilibrium (Q(e)) and percentage of adsorption (eta%) with a fixed adsorbent dose of 0.5 g L(-1) were found to be 181.9 mg g(-1) and 90.95%, respectively, when MO concentration, temperature, pH and equilibrium time were 100 mg L(-1), 298 K, 6.0 and 120 min, respectively. The isotherms showed that the adsorption of MO by Zn/Al-LDO was both consistent with Langmuir and Freundlich equations. The adsorption process was spontaneous and endothermic in nature and followed pseudo-second-order kinetic model. The calculated value of E(a) was found to be 77.1 kJ mol(-1), which suggests that the process of adsorption of methyl orange is controlled by the rate of reaction rather than diffusion. The possible mechanism for MO adsorption has also been presumed. In addition, the competitive anions on adsorption and the regeneration of Zn/Al-LDO have also been investigated.