微波消解-石墨炉原子吸收光谱法和原子荧光光谱法测定蔬菜中痕量元素

用微波消解对蔬菜进行前处理，石墨炉原子吸收光谱法和原子荧光光谱法测定蔬菜中铅、镉、砷、汞的含量。用两种国家标准参考样品进行考察，结果表明该方法不仅简便、快捷而且分析结果可靠。并提出了该方法在蔬菜痕量元素测定中应注意的问题。     

测定川芎中有害金属元素的三种样品前处理方法的比较试验

用3种不同的样品前处理方法,即①常规湿法酸消解法、②微波加热酸消解法及③干灰化法分别对川芎样作前处理溶解,用石墨炉原子吸收光谱法(GF-AAS)测定试液中铅、铜和镉的含量,用氢化物发生-原子荧光光谱法(HG-AFS)测定试液中砷和汞的含量。结果表明:用方法①及方法③处理样品所得溶液中,铅、铜和镉的回收率在83.0%～121.0%之间,而汞和砷的回收率很低。在方法②处理样品所得溶液中,测得砷、铜、镉及汞的回收率达97.0%～127.0%之间,而铅的回收率较低,仅为51.8%。总之,方法①适合用于GF-AAS测定铅时的样品前处理,方法②宜用于HG-AFS测定汞和砷时的样品前处理,而方法③宜应用于GF-AAS测定铜及镉时的样品前处理。     

微波消解-石墨炉原子吸收光谱法分析测定食用菌中总砷

摘 要：采用微波消解-石墨炉原子吸收光谱法分析测定食用菌中总砷。取可食部分的食用菌粉碎均匀,采用微波消解对样品进行消解,将消解液于140℃赶酸至0.5mL ,用超纯水转移定容至25mL。以0.1%的硝酸钯为基体改进剂,塞曼扣背景,用石墨炉原子吸收光谱法测定总砷。方法检出限为0.4μg/L,线性范围为0~30 μg/L,线性相关系数(r)大于0.998,采用精密度考察方法重现性,不同浓度水平的RSD%均小于6.6%;三个浓度水平的加标回收率为80.6% ~ 103.9%,有证标准物质测定结果符合要求。实验结果表明,方法操作简便、灵敏、准确,适合食用菌中总砷的测定。对砷形态复杂的野生食用菌,微波消解后可直接采用石墨炉原子吸收光谱法测定总砷。     

土壤中铅的分析方法比对

对不同的样品消解方法及电感耦合等离子体质谱、电感耦合等离子体原子发射光谱、石墨炉原子吸收光谱法测定土壤中铅的测定结果进行比对。采用电热板、微波及水浴3种加热方式,选择硝酸、氢氟酸、双氧水、王水、高氯酸、盐酸的不同组合进行土壤样品消解,通过分析测定值的精密度和准确度,考察消解体系对电感耦合等离子体质谱、电感耦合等离子体发射光谱、石墨炉原子吸收光谱法测定结果的影响。结果表明采用电感耦合等离子体质谱法测定土壤中的铅,最适宜的消解体系是硝酸-氢氟酸-高氯酸(微波加热),采用电感耦合等离子体原子发射光谱法测定最适宜的消解体系是硝酸(电热板加热),采用石墨炉原子吸收光谱法测定最适宜的消解体系是硝酸-盐酸-高氯酸(微波加热)。电感耦合等离子体质谱法的精密度和准确度优于另外两种方法。     

微波消解-石墨炉原子吸收光谱法测定纸质食品包装材料中的痕量镉

建立了微波消解–石墨炉原子吸收光谱法测定纸质食品包装材料中痕量镉的检验方法。样品经微波消解后,以硝酸镍为基体改进剂,试验确定了石墨炉原子吸收法测定镉的最佳仪器条件。镉的质量浓度在0～10μg/L与吸收峰面积呈良好的线性关系,线性相关系数r=0.9997,检出限为0.025μg/L。将该法用于纸质食品包装材料中痕量镉的测定,并进行加标回收试验,回收率为96.0%～105.5%,相对标准偏差不大于4.4%(n=10)。     

微波消解–石墨炉原子吸收光谱法测定84消毒剂中的痕量铅

建立了84消毒剂中痕量铅的微波消解–石墨炉原子吸收光谱测定方法。84消毒液以硝酸为消解试剂,用微波消解法进行消解。用2%磷酸二氢铵为基体改进剂,在优化后的仪器工作条件下测定。铅的质量浓度在0~80.0ng/mL范围内与吸光度呈良好的线性关系,线性相关系数r=0.999 3,方法检出限为0.005 4 mg/kg,平均回收率为94.66%,测定结果的相对标准偏差为1.87%(n=6)。该方法灵敏度与准确度高,可用于84消毒剂中痕量铅的检测。     

原子吸收光谱法测定克氏原螯虾体内铅、镉、铜时样品前处理方法的比较

在石墨炉原子吸收光谱法测定克氏原螯虾体内铅、镉和铜的含量时,比较了微波加热消解(方法1#)和干法消解(方法2#)两种样品前处理方法。结果表明:从测定精密度而论,方法1#略优于方法2#,上述3元素测定值的相对标准偏差(n=6)值,方法1#在0.7%~9.4%之间,方法2#在2.2%~14.8%之间;从准确度方面,方法1#亦优于方法2#,所测得方法1#的回收率在90.2%~94.3%,而方法2#的回收率在78.3%~82.8%之间。总体上看,微波消解法更适用于石墨炉原子吸收光谱法测定克氏原螯虾体内的铅、镉和铜含量时作为样品的前处理方法。     

石墨炉原子吸收光谱法测定中药口服液中的铬铅镉

利用石墨炉原子吸收光谱法测定,采用常温消解和密闭微波消解等方式处理口服液样品,并进行比较。结果表明,采用HNO3 HClO4 H2O2作为消解试剂用常温消解方式进行消解后,可不加基体改进剂直接进行测定,在此基础上研究了石墨炉原子吸收测定的最佳条件。应用这种方法测定了双黄连、清开灵、生脉饮和抗病毒口服液中痕量镉、铬和铅,RSD小于5．0％,回收率在83．4％～113％。     

GFAAS法测定蘑菇中的痕量铅

70年代中期 ,国外有人利用微波技术促进样品的消解 ,此后二十多年 ,国内外对微波消解技术均进行了许多研究。本文采用微波制样技术 ,硝酸镁基体改进剂 ,石墨炉原子吸收光谱法 (GFAAS)测定蘑菇中痕量铅 ,取得了良好的效果。     

电感耦合等离子体发射光谱法(ICP-OES)与石墨炉原子吸收光谱法测定饮用水中重金属元素的比较

通过对比电感耦合等离子体原子发射光谱法(ICP-OES)与石墨炉原子吸收光谱法(GF-AAS)测定水中重金属的检出限、精密度、加标回收率等实验,验证两种方法的准确性,从而为饮用水中重金属的测定提供可靠的方法。结果表明,石墨炉原子吸收光谱法测定饮用水中砷、镉、铬、铅、汞、硒的检出限均低于ICP-OES法,但ICP-OES法测定线性范围宽,重复性和加标回收率均优于石墨炉原子吸收光谱法,分析速度快,操作便捷,结果满意,是目前饮用水中重金属测定非常可靠的方法。     

Determination of trace elements in Antarctic krill samples by inductively coupled atomic emission and graphite furnace atomic absorption spectrometry

Analytical methods were developed for the determination of trace elements in Antarctic krill samples applying inductively coupled plasma atomic emission spectrometry (ICP-AES) and graphite furnace atomic absorption spectrometry (GF-AAS). Cu, Fe, Mn and Zn were determined by ICP-AES, while Cd and Pb by GF-AAS technique. Two microwave assisted digestion procedures were elaborated for the preparation of 0.5-g krill samples using open and closed vessel systems. The efficiency of the digestion processes was checked by measurements of the total organic carbon content of the solutions obtained. The deviations of the analytical data from the certified values and the relative standard deviations of the concentration measurements were lower for all six elements investigated applying the closed vessel digestion system.     

微波消解-石墨炉原子吸收光谱法测定胶囊中的痕量铬

研究了微波消解-石墨炉原子吸收光谱法测定胶囊中痕量铬的方法.选择HNO3作为微波消解的酸,通过干扰试验,发现该方法的选择性满足要求.方法线性关系良好,相关系数r2=0.999 8,检出限为1.7×10-14g,测定结果的相对标准偏差为2.63%(n=7),加标回收率为95.0%～104.0%.方法灵敏度高,重复性好,适...     

微波消解石墨炉原子吸收法测定环境空气中痕量锡

建立石墨炉原子吸收法测定环境空气中痕量锡的方法。采用混合纤维素微孔滤膜采集环境空气样品,用硝酸–氢氟酸微波消解样品,以5%硝酸镧–10%酒石酸混合液作基体改进剂,石墨炉原子吸收法进行测定。当采样体积为4 800 L,定容体积50 m L时,方法检出限为0.024μg/m~3,样品加标回收率为96.0%~106.0%,测定结果的相对标准偏差为2.74%~5.81%(n=7)。该方法样品处理操作过程简单,酸用量少,可用于环境空气中痕量锡的测定。     

一次消解土壤样品测定汞、砷和硒

建立了测定土壤中3种挥发性元素(汞、砷、硒)的一次消解方法,确定以程序控温石墨自动消解仪+王水-氢氟酸-硼酸络合敞开体系为最佳消解体系,采用氢化物发生-原子荧光光谱法(HG-AFS)分别测定同一消解液中汞、砷、硒的含量.采用国家标物中心有证标准物质土壤环境样品GSS-1~GSS-8进行了方法验证,结果均符合标准偏差的允许范围.此消解方法相比于现行标准方法,避免了针对各元素的分次处理,简化了消解步骤,节省了前处理时间,减少了试剂消耗,提高了实验效率,适用性广、灵敏度高、检出限低,尤其适合批量样品的微量/痕量元素分析,可作为一种大规模土壤样品中重金属污染监测和治理的快捷方法.     

微波消解-GFAAS法测定菠菜粉和蘑菇粉中微量镉的研究

应用微波消解-石墨炉原子吸收光谱法对菠菜粉和蘑菇粉中微量镉的含量进行测定。菠菜粉和蘑菇粉经HNO3+H2O2微波消解体系消解后,采用磷酸二氢铵作为基体改进剂,灰化温度为900℃,原子化温度为1 350℃,镉含量在0~2 ng/mL范围内与吸光度呈线性关系,线性相关系数为0.999 4,检出限为0.02 mg/kg。该法测定结果的相对标准偏差小于4%(n=6),加标回收率为96.7%~103.2%。     

Microwave-assisted digestion procedure for the determination of palladium in road dust

The present publication describes a microwave-assisted digestion procedure for the subsequent trace and ultra-trace analysis of palladium in road dust of varying origin. Digestion reagents are nitric acid, hydrogen peroxide and hydrofluoric acid. Boric acid is used as masking agent for fluoride ions to avoid removal of excess hydrofluoric acid by vaporization. After the three-step digestion procedure, a colorless and residue-free solution is obtained in which the determination of palladium can be directly performed using a recently developed highly selective on-line pre-concentration system, coupled with graphite furnace atomic absorption spectrometry (GF-AAS). Dust samples of varying origin (tunnel dust, road dust, filter dust from Frankfurt, Munich and Japan) and sampling dates (1987-2001) were investigated and characterized in detail with respect to matrix composition and palladium content. Validation of the analytical results was performed by recovery experiments.     

Determination of ultra-trace amounts of nickel in environmental samples by atomic absorption spectrometry with in-situ trapping of volatile species in an iridium–palladium coated graphite furnace

A sensitive and accurate method is described for the determination of ultra-trace nickel in environmental samples with in-situ trapping of volatile species in iridium-palladium coated graphite furnace atomic absorption spectrometry. The effects of the conditions for the generation and collection of volatile nickel species, such as medium acidity, potassium borohydride concentration, enhancement reagent concentration, reaction temperature, as well as graphite tube coating, carrier gas flow rate and trapping time were investigated. Phenanthroline was selected as the enhancement reagent due to its good enhancing effect, and iridium–palladium coating was used for the in-situ trapping of volatile nickel species at 300°C. Under the optimal conditions, the calibration curve was linear from 0.21 up to 30.0 ng mL^?1 with correlation coefficient of 0.9991, the detection limit (S/N = 3) was 0.21 ng mL^?1 for 4 mL sample volumes and the relative standard deviation for 11 determinations of Ni at 10 ng mL^?1 was 3.5%. The results found by the proposed methods are accordant with the certified values of water, soil and tea certified reference materials. The proposed methods have been applied for the determination of ultra-trace Ni in tap, river and wastewater, as well as rice and soil samples, with recoveries ranging from 97.3 to 100.5%.     

In-situ vaporization and matrix removal for the determination of rare earth impurities in zirconium dioxide by electrothermal vaporization inductively coupled plasma atomic emission spectrometry

A novel method for the determination of trace rare earth impurities in ZrO₂ powder has been developed based on electrothermal vaporization inductively coupled plasma atomic emission spectrometry. A polytetrafluoroethylene slurry was used as a fluorinating reagent to convert both the matrix (Zr) and the analytes (rare earth elements) into fluorides with different volatilities at a high temperature in a graphite furnace. The more volatile ZrF₄ was removed in-situ by selective vaporization prior to the determination of the analytes, removing matrix spectral interferences. Under optimum operating conditions, the absolute detection limits of the analytes varied from 0.04 ng (Yb) to 0.50 ng (Pr) with relative standard deviations less than 5%. The recommended approach has been successfully applied to the determination of trace rare earth impurities (La, Pr, Eu, Gd, Ho and Yb) in ZrO₂ powder and the results were in good agreement with those obtained by pneumatic nebulization inductively coupled plasma atomic emission spectrometry after the separation of the matrix using a solvent extraction procedure.     

Reductive coprecipitation as a separation method for the determination of gold,palladium, platinum,rhodium, silver,selenium and tellurium in geological samples by graphite furnace atomic absorption spectrometry

A method for the separation of Au, Pd, Pt, Rh, Ag, Te and Se from geological samples at trace levels is presented. The elements are separated from the matrix after dissolution by reductive coprecipitation using mercury as a collector and tin(II) chloride as a reductant. The efficiency of coprecipitation is studied by varying the acidity of the solutions and the amount of collector. The analyte elements are determined by graphite furnace atomic absorption spectrometry. In the determination of volatile elements (Te, Au and Ag), matrix modification with iridium is used. Selenium is determined with a mixed matrix modifier containing ascorbic acid and iridium. The method is tested by analysing geochemical reference samples.