Epitaxial ZnO thin films grown by pulsed electron beam deposition

In this work, the pulsed electron beam deposition method (PED) is evaluated by studying the properties of ZnO thin films grown on c-cut sapphire substrates. The film composition, structure and surface morphology were investigated by means of Rutherford backscattering spectrometry, X-ray diffraction and atomic force microscopy. Optical absorption, resistivity and Hall effect measurements were performed in order to obtain the optical and electronic properties of the ZnO films. By a fine tuning of the deposition conditions, smooth, dense, stoichiometric and textured hexagonal ZnO films were epitaxially grown on (0001) sapphire at 700 °C with a 30° rotation of the ZnO basal plane with respect to the sapphire substrate. The average transmittance of the films reaches 90% in the visible range with an optical band gap of 3.28 eV. Electrical characterization reveals a high density of charge carrier of 3.4 × 10¹⁹ cm^?3 along with a mobility of 11.53 cm²/Vs. The electrical and optical properties are discussed and compared to ZnO thin films prepared by the similar and most well-known pulsed laser deposition method.     

Low-temperature growth of Y2O3 thin films by ultraviolet-assisted pulsed laser deposition

Thin Y₂O₃ films have been grown on (100) Si using an in-situ ultraviolet-assisted pulsed laser deposition (UVPLD) technique. When compared to conventional pulsed laser deposited (PLD) films under similar conditions, the UVPLD-grown films exhibited better structural and optical properties, especially those grown at lower substrate temperatures, from 200 °C to 400 °C. X-ray diffraction investigations showed that the films grown were highly crystalline and textured. According to X-ray photoelectron spectroscopy and Rutherford backscattering spectrometry investigations, UVPLD-grown Y₂O₃ films have a better overall stoichiometry and contain less physisorbed oxygen than the conventional PLD-grown films. The refractive index values, measured in the range 300-750 nm by using variable-angle spectroscopic ellipsometry, were similar to those of a reference Y₂O₃ film.     

Epitaxial Properties of Co-Doped ZnO Thin Films Grown by Plasma Assisted Molecular Beam Epitaxy

High quality Co-doped ZnO thin films are grown on single crystalline Al2O3（0001） and ZnO（0001） substrates by oxygen plasma assisted molecular beam epitaxy at a relatively lower substrate temperature of 450℃. The epitaxial conditions are examined with in-situ reflection high energy electron diffraction （RHEED） and ex-situ high resolution x-ray diffraction （HRXRD）. The epitaxial thin films are single crystal at film thickness smaller than 500nm and nominal concentration of Co dopant up to 20%. It is indicated that the Co cation is incorporated into the ZnO matrix as Co^2＋ substituting Zn^2＋ ions. Atomic force microscopy shows smooth surfaces with rms roughness of 1.9 nm. Room-temperature magnetization measurements reveal that the Co-doped ZnO thin films are ferromagnetic with Curie temperatures Tc above room temperature.     

Structural study of TiO2 thin films by micro-Raman spectroscopy

The Raman spectroscopy method was used for structural characterization of TiO₂ thin films prepared by atomic layer deposition (ALD) and pulsed laser deposition (PLD) on fused silica and single-crystal silicon and sapphire substrates. Using ALD, anatase thin films were grown on silica and silicon substrates at temperatures 125–425 °C. At higher deposition temperatures, mixed anatase and rutile phases grew on these substrates. Post-growth annealing resulted in anatase-to-rutile phase transitions at 750 °C in the case of pure anatase films. The films that contained chlorine residues and were amorphous in their as-grown stage transformed into anatase phase at 400 °C and retained this phase even after annealing at 900 °C. On single crystal sapphire substrates, phase-pure rutile films were obtained by ALD at 425 °C and higher temperatures without additional annealing. Thin films that predominantly contained brookite phase were grown by PLD on silica substrates using rutile as a starting material.     

Off-axis pulsed laser deposition system for epitaxial oxide growth on substrates up to 2 inches in diameter

A novel off-axis pulsed-laser deposition (PLD) system for ferroelectric oxide thin films has been developed. The substrates are mounted "upside-down" and are rotating. The maximum substrate size is 2 inches in diameter. The optical and structural properties of the grown BaTiO₃ films are compared to the films produced by an on-axis PLD system. The stoichiometry and thickness were checked with Rutherford backscattering spectrometry (RBS). The crystalline quality and orientation were investigated with X-ray diffraction (XRD) and Rutherford backscattering spectrometry in channeling configuration (RBS/C). Using atomic force microscopy, the rms surface roughness was measured. The BaTiO₃ films grown on MgO form a planar optical waveguide. The optical losses and the refractive indices of these waveguides were determined with a prism coupling setup. Films grown on 10᎒ mm² MgO (100) substrates in on-axis geometry show optical waveguide losses less than 3 dB/cm.     

XRD study on the effect of the deposition condition on pulsed laser deposition of ZnO films

Using a pulsed laser deposition (PLD) process on a ZnO target in an oxygen atmosphere, thin films of this material have been deposited on Si(111) substrates. An Nd: YAG pulsed laser with a wavelength of 1064 nm was used as the laser source. The influences of the deposition temperature, laser energy, annealing temperature and focus lens position on the crystallinity of ZnO films were analyzed by X-ray diffraction. The results show that the ZnO thin films obtained at the deposition temperature of 400°C and the laser energy of 250 mJ have the best crystalline quality in our experimental conditions. The ZnO thin films fabricated at substrate temperature 400°C were annealed at the temperatures from 400°C to 800°C in an atmosphere of N₂. The results show that crystalline quality has been improved by annealing, the optimum temperature being 600°C. The position of the focusing lens has a strong influence on pulsed laser deposition of the ZnO thin films and the optimum position is 59.5 cm from the target surface for optics with a focal length of 70 cm.      

Effect of Annealing Temperature on Structural and Optical Properties of N-Doped ZnO Films

Nitrogen-doped ZnO （ZnO：N） films are prepared by thermal oxidation of sputtered Zn3N2 layers on A1203 substrates. The correlation between the structural and optical properties of ZnO：N films and annealing temperatures is investigated. X-ray diffraction result demonstrates that the as-sputtered Zn3N2 films are transformed into ZnO：N films after annealing above 600℃. X-ray photoelectron spectroscopy reveals that nitrogen has two chemical states in the ZnO：N films： the No acceptor and the double donor （N2）o. Due to the No acceptor, the hole concentration in the film annealed at 700℃ is predicted to be highest, which is also confirmed by Hall effect measurement. In addition, the temperature dependent photoluminescence spectra allow to calculate the nitrogen acceptor binding energy.     

Annealing effects of sapphire substrate on properties of ZnO films grown by magnetron sputtering

The annealing effects of sapphire substrates on the quality of epitaxial ZnO films grown by dc reactive magnetron sputtering were studied. The atomic steps formed on (0001) sapphire (α-Al₂O₃) substrates surface by annealing at high temperature were analyzed by atomic force microscopy. Their influence on the growth of ZnO films was examined by X-ray diffraction and photoluminescence measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface. The optimum annealing temperature of sapphire substrates for ZnO grown by magnetron sputtering is 1400 °C for 1 h in air. PACS 81.40.Ef; 68.55.Jk; 81.05.Dz; 81.15.Cd     

Measurement and Analysis of Composition and Depth Profile of H in Amorphous Si1-xCx:H Films

Composition in amorphous Si1-xCx：H heteroepitaxial thin films on Si （100） by plasma enhanced chemical vapour deposition （PECVD） is analysed. The unknown x （0.45-3.57） and the depth profile of hydrogen in the thin films are characterized by Rutherford backscattering spectrum （RBS）, resonance-nuclear reaction analysis （R-NRA） and elastic recoil detection （ERD）, respectively. In addition, the depth profile of hydrogen in the unannealed thin films is compared to that of the annealed thin films with rapid thermal annealing （RTA） or laser spike annealing （LSA） in nitrogen atmosphere. The results indicate that the stoichiometric amorphous SiC can be produced by PECVD when the ratio of CH4/SiH4 is approximately equal to 25. The content of hydrogen decreases suddenly from 35% to 1% after 1150℃ annealing. RTA can reduce hydrogen in SiC films effectively than LSA.     

Characteristics of Ba0.5Sr0.5TiO3 thin films grown by ultraviolet-assisted pulsed laser deposition

The microstructure and properties of barium strontium titanate (BST) thin films grown by an in situ ultraviolet-assisted (UV-assisted) pulsed laser deposition (UVPLD) technique are reported in this paper. In comparison with BST films grown by conventional pulsed laser deposition (PLD) under similar conditions, but without UV illumination, the UVPLD-grown films exhibited improved structural, electrical, and optical properties. X-ray photoelectron spectroscopy showed that when exposed to atmosphere, Ba atoms from the outermost layers formed a thin layer of barium carbonate, which negatively affects the film electrical characteristics. UVPLD-grown films exhibited a smaller amount of Ba atoms within the carbonate layer, resulting in better electrical characteristics. The dielectric constant of 40-nm-thick films deposited at 650 °C by UVPLD and PLD were determined to be 281 and 172, respectively. The leakage current density of the UVPLD-grown films was in the mid-10^-8 A/cm² range, a factor of 2 lower than that obtained from PLD-grown films.     

Deposition of Ti:sapphire thin films by reactive pulsed laser ablation using liquid metals and oxygen

Ti:sapphire films were grown using molten Al-Ti alloy ablation targets with either O₂ gas pulses or O₂ background reactive medium on sapphire (0001) substrates. The films were characterized by the use of XRD, RHEED, AFM, and XPS. While the films deposited at a substrate temperature of 650 °C showed three-dimensional epitaxial growth, the films deposited at 1000 °C exhibited a two-dimensional structure. Annealing of the low-temperature deposited films improved the crystal quality but failed to improve the surface morphology. Ti exists in the host sapphire lattice in the form of Ti³⁺ for films deposited at lower temperatures, whereas it assumes the tetravalent form in the high-temperature deposited films. The valence states of Ti identified by XPS studies are in agreement with low-temperature luminescence results.     

Effects of crystallinity on laser-induced voltage effect from Zn0.9Co0.1O thin film

Co-doped ZnO epilayer films were grown by pulsed laser deposition (PLD) on vicinal cut silicon and sapphire substrates. Changes in deposition time were observed as a moderate effect on the quality of the films, and the influence of the thickness on thermoelectric signals from Zn_0.9Co_0.1O thin films were discussed. The effect of one of the main deposition parameters, the deposition time, on the crystallinity and electron mobility properties of the Zn_0.9Co_0.1O thin films grown on sapphire was investigated by means of X-ray diffraction (XRD) and laser-induced voltage (LIV) effect. It shown that the XRD rocking curve full-width half-maximun (FWHM) decreased as time increasing, and the LIV signals were observed along the tilting angle of the substrate orientation when the pulsed KrF excimer laser of 248 nm were irradiated on the films. When the films illuminated in pulse lasers, the highest signals occurred in the films with best crystalline quality, and the signals were higher in the films grown on sapphire than those on silicon substrates. It suggested that the electrical resistivity and electron mobility have close relations with not only the crystallinity but also with the interface of the thin films.     

Pulsed laser deposition of Zr–N codoped <Emphasis Type="Italic">p</Emphasis>-type ZnO thin films

Present p-type ZnO films tend to exhibit high resistivity and low carrier concentration, and they revert to their natural n-type state within days after deposition. One approach to grow higher quality p-type ZnO is by codoping the ZnO during growth. This article describes recent results from the growth and characterization of Zr–N codoped p-type ZnO thin films by pulsed laser deposition (PLD) on (0001) sapphire substrates. For this work, both N-doped and Zr–N codoped p-type ZnO films were grown for comparison purposes at substrate temperatures ranging between 400 to 700 °C and N₂O background pressures between 10⁻⁵ to 10⁻² Torr. The carrier type and conduction were found to be very sensitive to substrate temperature and N₂O deposition pressure. P-type conduction was observed for films grown at pressures between 10⁻³ to 10⁻² Torr. The Zr–N codoped ZnO films grown at 550 °C in 1×10⁻³ Torr of N₂O show p-type conduction behavior with a very low resistivity of 0.89 Ω-cm, a carrier concentration of 5.0×10¹⁸ cm⁻³, and a Hall mobility of 1.4 cm² V⁻¹ s⁻¹. The structure, morphology and optical properties were also evaluated for both N-doped and Zr–N codoped ZnO films.     

Epitactic growth of a decagonal phase in an Al–Ni–Co alloy film deposited on a (0001) sapphire substrate

Thin films of Al–Ni–Co alloy with an average thickness of 15?nm were produced by means of conventional vacuum deposition technique on (0001) sapphire substrates heated at various test temperatures. The microstructures and textures of the films obtained were thoroughly investigated by atomic force microscopy, X-ray diffraction and transmission electron diffraction and imaging techniques. The diffraction measurements have evidenced that the vacuum deposition of Al₇₂Ni₁₅Co₁₃ alloy on the substrates heated above 400°C allows a homogeneous poly-quasicrystalline film, consisting of the Ni-rich basic decagonal phase to grow. It has been further indicated by in-plane XRD analysis that the film deposited at 550°C contains a considerable amount of the decagonal grains epitaxially grown on the sapphire substrate. Possible epitaxial relations occurring between the deposit and the substrate will be detailed on the basis of results obtained from electron diffraction measurements.     

Adjusting chemical bonding of hard amorphous CSixNy thin films by N*-plasma-assisted pulsed laser deposition

Hard amorphous carbon silicon nitride thin films have been grown by pulsed laser deposition (PLD) of various carbon silicon nitride targets by using an additional nitrogen RF plasma source on [100] oriented silicon substrates at room temperature. The influence of the number of laser shots per target site on the growth rate and film surface morphology was studied. Up to about 30 at. % nitrogen and up to 20 at. % silicon were found in the films by Rutherford backscattering spectroscopy (RBS) and X-ray photoelectron spectroscopy (XPS). The XPS of the films showed a clear correlation of binding energy to the variation of PLD parameters. The films show a universal hardness value up to 23 GPa (reference value for silicon substrate 14 GPa) in dependence on target composition and PLD parameters. The results emphasise the possibility of variation of chemical bonding and corresponding properties, such as nanohardness, of amorphous CSi_xN_y thin films by the plasma-assisted PLD process.     

Effects of sapphire substrates surface treatment on the ZnO thin films grown by magnetron sputtering

The surface treatment effects of sapphire substrate on the ZnO thin films grown by magnetron sputtering were studied. The sapphire substrates properties have been investigated by means of atomic force microscopy (AFM) and X-ray diffraction rocking curves (XRCs). The results show that sapphire substrate surfaces have the best quality by CMP with subsequent chemical etching. The surface treatment effects of sapphire substrate on the ZnO thin films were examined by X-ray diffraction (XRD) and photoluminescence (PL) measurements. Results show that the intensity of (0 0 2) diffraction peak of ZnO thin films on sapphire substrates treated by CMP with subsequent chemical etching was strongest, FWHM of (0 0 2) diffraction peak is the narrowest and the intensity of UV peak of PL spectrum is strongest, indicating surface treatment on sapphire substrate preparation may improve ZnO thin films crystal quality and photoluminescent property.     

Synthesis and characterization of laser ablated TiNi films

TiNi thin films with BaTiO₃ and PbZr_0.52Ti_0.48O₃ (PZT) as buffer layers were deposited on Si(100) substrates by the pulsed laser deposition (PLD) method. Buffer layers (BaTiO₃ and PZT) were deposited at 600 °C in oxygen (O₂) environment and TiNi films were deposited on the top of the buffer layer in presence of 15 mTorr nitrogen (N₂) at various deposition temperatures (50, 300, and 500 °C). Synthesis and characterization of TiNi films were investigated from the crystallographic point of view by using X-ray diffractometer (XRD) and atomic force microscope (AFM) techniques. It is found that buffer layer of BaTiO₃ and PZT have improved the crystallinity of TiNi films deposited at higher temperatures. The TiNi/PZT film was uniform compared to TiNi/BaTiO3 film with the exception of agglomerates that appeared throughout the layer.     

Growth of oriented Pb(ZrxTi1-x)O3 thin films on glass substrates by pulsed laser deposition

Oriented crystalline Pb(Zr_xTi_1-x)O₃ (x=0.53) (PZT) thin films were deposited on metallized glass substrates by pulsed laser deposition (1060-nm wavelength Nd:YAG laser light, 10-ns pulse duration, 10-Hz repetition rate, 0.35-J/pulse and 25-J/cm² laser fluence), from a commercial target at substrate temperatures in the range 380-400 °C. Thin films of 1-3 7m were grown on Au(111)/ Pt/NiCr/glass substrates with a rate of about 1 Å/pulse on an area of 1 cm². The deposited PZT films with perovskite structure were oriented along the (111) direction, as was revealed from X-ray diffraction spectra. Fourier transform infrared spectroscopy (FTIR) was performed on different PZT films so that their vibrational modes could be determined. Piezoelectric d₃₃ coefficients up to 30 pC/N were obtained on as-deposited films. Ferroelectric hysteresis loops at 100 Hz revealed a remanent polarization of 20 7C/cm² and a coercive field of 100 kV/cm.     

Studies on highly resistive ZnO thin films grown by DC-discharge-assisted pulsed laser deposition

It was found that by changing the substrate temperature from room temperature to ～850 °C, ZnO thin films with widely varying resistivity values could be grown on sapphire substrates using DC-discharge-assisted pulsed laser deposition (PLD) in oxygen ambient. The resistivity of the film grown at room temperature was too high to measure using our existing setup. However, as the growth temperature was increased from 550 °C to 750 °C, the resistivity first decreased slowly from ～14.0 to 4.4 Ω?m and then dropped suddenly to get saturated at ～2.0×10^?3 Ω?m as the growth temperature was further increased. In contrast to these, when there was no DC-discharge, the variation of resistivity for ZnO thin films grown by PLD was marginal up to the substrate temperature of ～850 °C. The reason for these observations was found to be the combined effects of reduction in donor defect densities like oxygen vacancies and zinc interstitials, introduction of acceptor type defects like interstitial oxygen and zinc vacancies, and the resultant poor carrier mobility at lower growth temperatures. At higher growth temperatures (800 °C and above), the appearance of oxygen vacancies and increase in mobility due to better crystalline quality were found to be responsible for reducing the resistivity. The PL of these films had significant emission in the green and red regions of the spectrum due to the aforesaid defect related transitions. Such highly resistive and luminescent films might be suited for applications such as resistive RAM, UV-photo detector, TFT, piezoelectric, transparent phosphor, and broadband LED applications.     

Fabrication of ZnO thin films by femtosecond pulsed laser deposition

The growth of ZnO thin films on sapphire substrate using the femtosecond PLD technique is reported. The effect of substrate temperature and oxygen pressure on the structural properties of the films was studied. Highly c-axis oriented ZnO films can be grown on sapphire substrates under vacuum conditions using the femtosecond PLD process. There is an optimum substrate temperature for the pulsed laser deposition of ZnO film that enhances the thermodynamic stability and allows the formation of well-crystallized thin films. The crystal quality of the films can be further improved by increasing the deposition time and introducing oxygen during the pulsed laser deposition process.