Characterization of lead free (K0.5Na0.5)NbO3-LiSbO3 piezoceramic

(K_0.5Na_0.5)NbO₃ (KNN) based lead free ceramics have been fabricated by a solid state reaction. In this work, LiSbO₃ (LS) modified KNN based ceramics were sintered at atmospheric pressure and high density (>96% theoretical) was obtained. The detailed elastic, dielectric, piezoelectric and electromechanical properties were characterized by using the resonance technique combined with the ultrasonic method. The full set of material constants for the obtained polycrystalline ceramics were determined and compared to the pure hot pressed KNN counterpart. KNN-LS polycrystalline ceramic was found to have higher elastic compliance, dielectric permittivity and piezoelectric strain coefficients, but lower mechanical quality factor, when compared to pure KNN, exhibiting a “softening” behavior. However, a high coercive field (∼17 kV/cm) was found for the LS modified KNN material. The properties as a function of temperature were determined in the range of −50-250 ^°C, showing a polymorphic phase transition near room temperature, giving rise to improved piezoelectric behavior.     

Synthesis and dielectric characteristics of La0.5Bi0.5MnO3 ceramics

La_0.5Bi_0.5MnO₃ ceramics with a single phase were prepared by a solid-state reaction method, and their dielectric properties were characterized. Two dielectric relaxations with a giant dielectric constant were identified in the temperature range from 125 to 350 K. The electron hopping between Mn³⁺ and Mn⁴⁺ was found to be the origin of the dielectric relaxation at low temperatures (125–200 K) with an activation energy of 0.18 eV. The high temperature (200–350 K) dielectric relaxation can be attributed to the conduction.     

Na0.25K0.25Bi0.5TiO3无铅压电陶瓷的介电特性研究

用固相反应法制备了Na_0.25K_0.25Bi_0.5TiO₃ (NKBT50)陶瓷，研究了该陶瓷在室温至400℃温度范围内的介电性能.发现该陶瓷的介电温谱与烧结气氛、极化状态有关.在空气中烧结的未极化样品在70℃附近存在介电和损耗峰，而极化后及在氧气氛中烧结的样品并不存在该介电、损耗峰.分析认为70℃的介电和损耗峰与氧空位形成的缺陷偶极子的极化弛豫有关.热激电流显示，陶瓷的去极化温度为225℃，与此相对应的介电、损耗峰也 关键词： 介电性能 氧空位 极化弛豫 钛酸铋钠钾     

Diffuse dielectric anomaly of （Na0.5K0.5Bi）0.5TiO3 crystal at high temperature

This paper investigates the dielectric properties of (Na_0.5K_0.5Bi)_0.5TiO₃ crystal at intermediate frequencies (1kHz \le f \le 1MHz) in the temperature range of 30--560℃. A pronounced high-temperature diffuse dielectric anomaly has been observed. This dielectric anomaly is shown to arise from a Debye-like dielectric dispersion that slows down following an Arrhenius law. The activation energy E_r obtained in the fitting process is about 0.69eV. It proposes that the dielectric peak measured at low frequency above 400℃ is not related to the phase transition but to a space-charge relaxation.     

High-temperature impedance spectroscopy of BaFe0.5Nb0.5O3 ceramics doped with Bi0.5Na0.5TiO3

Bi_0.5Na_0.5TiO₃ (BNT)-doped BaFe_0.5Nb_0.5O₃ (BFN) ceramics were synthesized by a two-step solid-state reaction. Temperature dependence of dielectric properties measured at different frequencies was investigated over broad temperature and frequency ranges. Impedance spectroscopy and universal dielectric response were employed to study the relaxation behavior and conductivity mechanism of the ceramics in a frequency range from 40 Hz to 100 MHz and a temperature range from 300 K to 800 K. The complex plane impedance data revealed the bulk and grain boundary contributions toward conductivity processes in the form of semicircular arcs. The high-temperature conductivity of ceramics is attributable to thermally activated second ionized oxygen vacancy.     

Sinterability studies on K0.5Na0.5NbO3 using laser as energy source

The sinterability of K_0.5Na_0.5NbO₃ (KNN) ceramics by a laser beam has been investigated in the present research. A 100 W CO₂ laser with a beam diameter of 0.6 mm has been used to sinter the KNN specimens prepared on a uniaxial pressing machine. The relations between laser power and thickness of densified layer, crystallographic structures and phase compositions have been studied. A comparison has been made between laser and furnace sintered KNN samples according to the SEM, XRD and XRF results. The possibility of KNN used for the layer-wise laser direct sintering 3D components has been confirmed in this paper.     

Oxygen-defects-related dielectric response in CaCu3Ti4O12 ceramics

A 10 mm thickness columned CaCu₃Ti₄O₁₂ ceramic was fabricated by the conventional solid-state reaction method and the dielectric properties of different parts in ceramic had been investigated. For the sample close to the surface, only one Debye-type relaxation around 10⁷ Hz was observed at room temperature. However, for the sample close to the core, another relaxation peak was observed at about 10⁴ Hz. The results were explained in terms of the equivalent circuit model by showing in the impedance spectroscopy. Moreover, it was introduced that the low-frequency dielectric relaxation is associated with the electrode-sample contact effect based on varying sample thickness and an annealing treatment in the nitrogen atmospheres.     

Properties of the solid solution (1−x)Na0.5Bi0.5TiO3-(x)BiFeO3

This study shows that remarkable electric and magnetic properties are encountered within the (1−x)Na_0.5Bi_0.5TiO₃ (NBT)-(x)BiFeO₃ (BF) solid solution. Dual ferroelectric and magnetic properties are observed in the BF-rich part of the solid solution implying intrinsic multiferroic character of the compounds. In addition, a relaxation phenomenon is evidenced within the overall compositional domain of the solid solution. This study emphasizes that in the NBT-rich part, the relaxor behaviour is very similar to that of NBT, while beyond x=0.5, it turns to a different mechanism of relaxation probably induced by the presence of oxygen vacancies resulting from the mixed valence of the iron cations.     

Dielectric retardation and relaxation in Bi0.5La0.5MnO3 ceramic at 80 K

Low-temperature (80 K) measurements are made of the frequency dependences of the real and imaginary parts of the complex dielectric constant and complex electric modulus of bismuth lanthanum manganite Bi_0.5La_0.5MnO₃ ceramic. The presence of two (low- and high-frequency) regions of dielectric retardation and relaxation is revealed. A considerable difference between the average rates of retardation and relaxation and the Debye value in the high frequency region is revealed and explained.     

Effect of deposition temperature on orientation and electrical properties of (K0.5Na0.5)NbO3 thin films by pulsed laser deposition

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) thin films have been prepared on Pt/TiO₂/SiO₂/Si substrates by pulsed laser deposition process. The structures, crystal orientations and electrical properties of thin films have been investigated as a function of deposition temperature from 680 °C to 760 °C. It is found that the deposition temperature plays an important role in the structures, crystal orientations and electrical properties of thin films. The crystallization of thin films improves with increasing deposition temperature. The thin film deposited at 760 °C exhibits strong (0 0 1) preferential orientation, large dielectric constant of 930 and the remnant polarization of 8.54 μC/cm².     

Electrical properties of SrBi2(Nb0.5Ta0.5)2O9 ceramics

Aurivillius SrBi₂(Nb_0.5Ta_0.5)₂O₉ (SBNT 50/50) ceramics were prepared using the conventional solid-state reaction method. Scanning electron microscopy was applied to investigate the grain structure. The XRD studies revealed an orthorhombic structure in the SBNT 50/50 with lattice parameters a=5.522 Å, b=5.511 Å and c=25.114 Å. The dielectric properties were determined by impedance spectroscopy measurements. A strong low frequency dielectric dispersion was found to exist in this material. Its occurrence was ascribed to the presence of ionized space charge carriers such as oxygen vacancies. The dielectric relaxation was defined on the basis of an equivalent circuit. The temperature dependence of various electrical properties was determined and discussed. The thermal activation energy for the grain electric conductivity was lower in the high temperature region (T>303.6 °C, E_a−ht=0.47 eV) and higher in the low temperature region (T<303.6 °C, E_a−lt=1.18 eV).     

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5Na0.5NbO3- 0.04LiSbO3 lead-free piezoelectric ceramics

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5+xNa0.5+xNbO3- 0.04LiSbO3 lead-free piezoelectric ceramics were examined for 0 ≤ x ≤ 0.02. The piezoelectric coefficients exhibited a maximum, d33 = 187 pC/N at x = 0.0075, coinciding with the maximum of the grain size and the apparent density at x = 0.0075. The apparent density and the piezoelectric coefficients decreased with increasing x at higher x which was likely due to the crystal geometrical distortion of 0.96K0.5+xNa0.5+xNbO3-0.04LiSbO3. In addition, super-large grains were found and this may be due to liquid phase sintering. Excess (K++Na+) attracted a sum of space charges to keep the charge neutral, resulting in charge leakage during the course of ceramic polarization, influencing the piezoelectric and ferroelectric properties. These findings are of importance for guiding the design of K0.5Na0.5NbO3-based lead-free ceramics with enhanced electrical properties.     

Fe掺杂CaCu3Ti4O12陶瓷的介电性能与弛豫特性研究

采用固相反应法制备了CaCu₃Ti_4-xFe_xO₁₂(0≤x≤0.2)陶瓷,通过X射线衍射、扫描电子显微镜、介电频谱和阻抗谱等手段研究了Fe对CaCu₃Ti₄O₁₂陶瓷的结构和介电性能的影响.研究发现：CaCu₃Ti_4-xFe_{x关键词： 巨介电常数 双阻挡层电容模型 界面极化}     

0.5NdAlO3-0.5CaTiO3电子结构及光学性质的第一性原理计算

采用基于第一性原理密度泛函理论的平面波赝势方法,对0.5NdAlO₃-0.5CaTiO₃晶体进行结构优化,并对其能带结构,态密度和光学性质进行了理论计算.结构优化后晶格参数与实验数据相符合,误差小于1%;能带计算结果表明0.5NdAlO₃-0.5CaTiO₃为间接带隙,带隙值为0.52eV;费米面附近的能带由Nd-4f,O-2p,Nd-4p,Al-3p,Ti-4d层的电子态密度确定.同时也计算了该结构的介电函数,反射率和复折射率等光学性质.     

Microwave dielectric properties of (1 − x)(Mg0.95Co0.05)TiO3–x(Na0.5La0.5)TiO3 ceramic system

The microstructures and the microwave dielectric properties of the (1 − x)(Mg_0.95Co_0.05)TiO₃–x(Na_0.5La_0.5)TiO₃ ceramic system were investigated. Two-phase system was confirmed by the XRD patterns and the EDX analysis. A co-existed second phase (Mg_0.95Co_0.05)Ti₂O₅ was also detected. The microwave dielectric properties are strongly related to the density and the matrix of the specimen. A new microwave dielectric material 0.88(Mg_0.95Co_0.05)TiO₃–0.12(Na_0.5La_0.5)TiO₃, possessing an excellent combination of dielectric properties: ε_r  22.36, Q × f  110,000 GHz (at 9 GHz), τ_f  2.9 ppm/°C), is proposed as a candidate dielectric for GPS patch antennas.     

Effect of bismuth deficiency on structure and electrical properties of (Na0.5Bi0.5)0.93Ba0.07TiO3 ceramics

(Na_0.5Bi_x)_0.93Ba_0.07TiO₃ (x=0.500-0.492) ceramics were prepared by a citrate method, and the structure and electrical properties of the ceramics were investigated with respect to the amount of Bi deficiency. It was detected that the Bi deficiency had a considerable impact on the crystal structure and microstructure. The inspection of both the temperature dependence of the dielectric properties (free permittivity ε₃₃^T/ε₀ and dielectric loss tan δ) and the evolution of the polarization-electrical field (P-E) hysteresis loops with measuring temperature suggests that the Bi deficiency served to increase the depolarization temperature (T_d). The Bi deficiency led to an increase in the coercive field (E_c) and mechanical quality factor (Q_m) together with a decrease in the remanent polarization (P_r) and piezoelectric constants (d₃₃). The variation of the structure and electrical properties with Bi deficiency amount was qualitatively interpreted in terms of the formation of Bi and oxygen vacancies in the Bi-deficient specimens. This research indicates the importance of adequately controlling Bi stoichiometry of (Na_0.5Bi_0.5)_0.93Ba_0.07TiO₃ ceramics in obtaining the desired ferroelectric and piezoelectric properties.     

Dielectric characteristics and polarization response of lead-free ferroelectric (Bi0.5Na0.5)0.94Ba0.06TiO3-P(VDF-TrFE) 0-3 composites

Bismuth sodium barium titanate/poly(vinylidene fluoride-trifluoroethylene) 70/30 [(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃-P(VDF-TrFE)] 0-3 composites were prepared by a hot-press method for different volume fractions of (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ ceramic powder in a P(VDF-TrFE) 70/30 copolymer matrix. The relative permittivity and dielectric loss of the composites increased with increase in the volume fraction of the ceramics, which well follows the Bruggeman model. The polarization responses of the composites were strongly dependent on the ceramic volume fraction. The composites with a higher ceramic volume fraction showed an increase in remanent polarization. At room temperature, a 0.3(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃-0.7P(VDF-TrFE) composite showed a relative permittivity ε_r=30, remanent polarization and coercive field      

Dielectric and piezoelectric properties of Fe2O3-doped (Na0.5K0.5)0.96Li0.04Nb0.86Ta0.1Sb0.04O3 lead-free ceramics

The effect of a small amount Fe₂O₃ (0.1-2 mol%) doping on the electrical properties of (Na_0.5K_0.5)_0.96Li_0.04Nb_0.86Ta_0.1Sb_0.04O₃ (NKLNTS) ceramics was investigated. It was found that the B-site substitution of Fe³⁺ does not change the crystal structure within the studied doping level and all modified ceramics have a pure tetragonal perovskite structure at room temperature. The addition of Fe₂O₃ can promote the sintering of NKLNTS ceramics, and simultaneously cause the grain growth so that Fe³⁺-doped NKLNTS compositions show degraded densification at higher doping level. Furthermore, the dielectric properties of the NKLNTS ceramics do not show a significant change by Fe₂O₃ doping. However, the addition of Fe₂O₃ was found to have a significant influence on the electric fatigue resistance and the durability against water. The presence of oxygen vacancies caused by the replacement of Fe³⁺ for B-site ions makes the NKLNTS ceramics harder.     

Piezoelectric non-linearity in PbSc0.5Ta0.5O3 thin films

Epitaxial (001)-oriented PbSc_0.5Ta_0.5O₃ (PST) thin films were deposited by pulsed laser deposition. Local piezoelectric investigations performed by piezoelectric force microscopy show a dual slope for the piezoelectric coefficient. A piezoelectric coefficient of 3 pm/V was observed at voltages up to 0.8 V. However, at voltages above 0.8 V, there is a steep increase in piezoelectric coefficient mounting to 23.2 pm/V. This nonlinear piezoelectric response was observed to be irreversible in nature. In order to better understand this nonlinear behavior, voltage dependent dielectric constant measurements were performed. These confirmed that the piezoelectric non-linearity is indeed a manifestation of a dielectric non-linearity. In contrast to classical ferroelectric systems, the observed dielectric non-linearity in this relaxor material cannot be explained by the Rayleigh model. Thus the dielectric non-linearity in the PST films is tentatively explained as a manifestation of a percolation of the polar nano regions.