电聚合硫菫膜修饰电极同时测定儿茶酚和氢醌

制备了电聚合硫堇膜修饰的玻碳电极(Thi/GCE),研究了儿茶酚(CC)和氢醌(HQ)在该修饰电极上的电化学行为.在CC和HQ共存体系中,二者在该修饰电极上与裸玻碳电极(GCE)相比,氧化峰电流增大且峰电位分别负移至165、68 mV,二者的氧化峰电位差变大且半峰宽变窄,使得两峰得以有效分离.据此利用差分脉冲伏安法可选...     

Au Nanowires-MWCNTs修饰电极对葡萄糖的催化氧化

通过油胺(Oleylamine)还原法制备了金纳米线(Au nanowires),将其与酸化处理的多壁碳纳米管(MWCNTs)通过层层组装制备了Au nanowires-MWCNTs复合结构修饰的玻碳电极(Au nanowires-MWCNTs/GCE).电化学研究结果表明,与单纯Au nanowires或MWCNTs修饰电极相比,Au nanowires-MWCNTs/GCE对葡萄糖表现出更优良的电催化性能.以Au nanowires-MWCNTs/GCE为阳极,电沉积Pt膜电极(Pt/GCE)为阴极,构建了葡萄糖/O2燃料电池.测试结果表明,构建的燃料电池的开路电位(OCP)为0.57 V,在0.44 V下最大功率密度(Pmax)为0.28 m W/cm2.     

苯胺在邻-氨基苯磺酸功能化的玻碳电极上聚合及其对抗坏血酸的电催化氧化

通过电氧化法将ABS分子以CN键共价键合在玻碳电极(GCE)表面,形成ABS分子单层膜修饰的GCE(ABS/GCE),在此电极上对AN进行电聚合,从而制备了聚苯胺/邻氨基苯磺酸复合膜修饰电极(PAN-ABS/GCE/CME).由于ABS中磺酸基功能团对PAN的掺杂作用使PAN在中性或碱性介质中都能呈现出较好的电化学活性.研究表明,PAN-ABS/GCE/CME在PBS(pH 6.8)中对AA的电氧化具有催化作用,其氧化峰电位为0.17 V,比在裸GCE上(0.39 V)负移了0.22 V,峰电流明显升高.AA在修饰电极上的氧化峰电流与其浓度在0.5～16.5 mmol/L范围内呈良好的线性关系,其线性回归方程为ipa(μA)=20.2+6.20CAA,r=0.9973; 检出限(3δ)为7.2 μmol/L,电极具有较好的稳定性和重现性.并采用计时电流法对AA催化氧化的扩散系数和催化速率常数进行了研究.     

纳米金/三聚氰胺修饰电极检测亚硝酸盐

采用电聚合方法制备三聚氰胺(MA)膜修饰玻碳电极(GCE),然后采用原位恒电位沉积法制备金纳米颗粒(Au),并将其修饰于膜电极表面,制得纳米金/三聚氰胺修饰玻碳电极(Au/MA/GCE)。用扫描电子显微镜(SEM)对修饰电极进行表面形貌和元素成分分析。用循环伏安法研究亚硝酸根(NO2-)在该修饰电极上的电化学行为发现,NO2-在0.85 V出现一灵敏的氧化峰。在优化的实验条件下,NO2-在1.0×10-5～1.0×10-3mol/L浓度范围内与其氧化峰电流成线性关系,检测下限为8.9×10-7mol/L。将修饰电极用于实际样品中NO2-的检测,效果良好。     

重金属Cr(Ⅵ)离子与血清白蛋白的结合反应机制研究

电聚法制备聚苯胺修饰电极(PANI/GCE),并通过循环伏安法和电化学交流阻抗法表征修饰电极;利用修饰电极研究Cr(Ⅵ)离子与血清白蛋白(Bovine serum albumin,BSA)的结合反应机制并构建理论模型方程.结果表明,成功制备PANI/GCE修饰电极,修饰电极测定Cr(Ⅵ)-BSA分子相互作用结果显示良好的线性响应关系,利用建立的理论模型方程计算Cr(Ⅵ)与蛋白质的结合参数(β=2.07×104 L.mol-1,n=1.03),说明Cr(Ⅵ)与血清白蛋白存在明显的相互作用.     

石墨烯修饰电极电化学阻抗法测量油脂的氧化诱导时间

分别采用滴涂法制备石墨烯(GR)-壳聚糖(CS)修饰玻碳电极(GR-CS/GCE),以及电沉积-还原氧化石墨烯(GO)修饰玻碳电极(rGO/GCE),并对修饰电极进行了电化学表征。结果表明,rGO/GCE比GR-CS/GCE及GCE有较小的电子转移阻抗和较大的表观活性面积。rGO/GCE电极的制备条件为GO悬浮液浓度1.0g/L、扫描速度20mV/s和电沉积30圈。优化了油脂阻抗测量条件,研究了油脂样品在rGO/GCE上的交流阻抗行为。根据rGO/GCE可以快速、准确地测量实际油脂样品(杏仁油)氧化过程中阻抗值及其变化,据此建立了一种简便、灵敏和准确测量油脂氧化诱导时间的电化学分析方法。     

基于聚亚甲基蓝-碳纳米管复合膜固载血红蛋白的H2O2生物传感器

采用吸附和电化学聚合修饰方法,制得了聚亚甲基蓝-碳纳米管聚合膜玻碳电极(PMB-MWNTs/GCE),再将血红蛋白(Hb)固定在PMB-MwNTs/GCE表面,制备了稳定的Hb/PMB-MwNTs//GCE的H2O2生物传感器,并用循环伏安法对修饰电极的生物电催化行为进行了表征.研究结果表明,固定在PMB-MWNTs/...     

桑色素/石墨烯修饰电极的制备及对多巴胺的选择性灵敏测定

在石墨烯纳米片修饰电极(GN/GCE)上,通过电聚合的方法制备了新颖的桑色素/石墨烯复合修饰电极(M/GN/GCE).以多巴胺(DA)和抗坏血酸(AA)为模型化合物,运用循环伏安法(CV)和差示脉冲伏安法(DPV)考察了该复合修饰电极的电催化行为.在pH 7.0的PBS中,DA和AA分别在0.172 V和-0.183 V产生氧化峰,峰位差达355 mV.与单一修饰电极(桑色素修饰电极(M/GCE)、石墨烯修饰电极(GN/GCE)及裸玻碳电极(GCE))相比,DA在M/GN/GCE上的峰电流显著增大.在优化的实验条件下,DA在2.0×l0-8～5.5×10-4 mol/L浓度范围内与其峰电流具有良好的线性关系,检出限达9.0×10-9 mol/L.     

CdTe量子点修布电极的阳极电致化学发光

制备了CdTe量子点/Nafion修饰玻碳电极(CdTe QDs/Nafion/GCE),并研究了该修饰电极在中性磷酸盐缓冲溶液(PBS)中的电致化学发光(ECL)行为.结果表明,三丙胺(TPA)作为共反应剂存在时,QDs/Nafion/GCE在中性PBS中可以产生强的阳极电化学发光信号.考察了量子点的用量、Nafion的用量、pH、电解质等条件对ECL的影响.抗坏血酸对QDs/Nafion/GCE的ECL具有抑制作用,且抑制程度与抗坏血酸浓度呈线性关系,为利用电致化学发光法检测抗坏血酸提供了新方法.     

聚对氨基苯磺酸/石墨烯复合修饰电极对尿酸的选择性灵敏测定

采用电聚合方法在石墨烯纳米片(GN)的表面聚合一层聚对氨基苯磺酸(PABSA),制备了聚对氨基苯磺酸/石墨烯复合修饰玻碳电极(PABSA/GN/GCE)。研究了尿酸(UA)和抗坏血酸(AA)在该修饰电极上的电化学行为。与聚对氨基苯磺酸修饰电极(PABSA/GCE)及石墨烯单层膜修饰电极(GN/GCE)相比,复合修饰电极PABSA/GN/GCE显著提高了对UA和AA的检测灵敏度和分离度。在0.1 mol/L磷酸盐缓冲溶液(pH7.0)中,UA和AA的峰电位差达344 mV,表明PABSA/GN/GCE能实现对UA的选择性测定。UA的峰电流与其浓度呈良好的线性关系,线性范围为1.0×10-7～8.0×10-4mol/L,检出限为4.5×10-8mol/L。该复合修饰电极用于尿样中尿酸的测定,结果满意。     

Characteristics of a surface plasmon resonance sensor combined with a poly(vinyl chloride) film-based ionophore technique for metal ion analyses.

The characteristics of a surface plasmon resonance (SPR) sensor prepared by coating a metal film evaporated on a prism with a polymer film containing tetra-n-butyl thiuram disulfide (TBTDS) were studied. The differences in the sensitivity, selectivity, and detection limit for a Zn2+ ion of the SPR sensor were reported as a function of the thickness of the polymer film, the kind of a metal film, and the kind of a polymer film. The thinner was the polymer film, the higher was the sensitivity, and the lower was the detection limit. The Ag film gave to the SPR sensor higher sensitivity than the Au film. TBTDS contained in the poly(vinyl chloride) (PVC) film slightly improved the selectivity toward the Zn2+ ion. A non-conditioned poly(methyl methacrylate) (PMMA) film containing TBTDS gave a lower detection limit of 1.0 x 10(-6) mol/l, which is similar to that obtained by using an ion selective electrode (ISE) method, than the PVC film. The PVC film, however, gave higher concentration resolution than the PMMA film.     

Facile formation of water-insoluble cyclodextrin/Nafion composite films on solid surfaces

The water-insoluble poly-beta-cyclodextrin (poly-CD)/Nafion composite film was easily prepared by casting a mixed solution of poly-CD and Nafion onto substrate plates. FT-IR measurements showed that the 50/50 wt% poly-CD/Nafion composite film remained stable on the glass and quartz substrates after immersion in water for more than 3 h, while a pure poly-CD film was almost completely dissolved by immersion within 1 h. The film stability was also evaluated from the amount of p-nitrophenol (p-NP) inclusion in the film, which was determined from the decrease in UV-vis absorbance of the p-NP solution into which the film was immersed. The composition dependence of the inclusion amount showed that the film was stable up to 50 wt% CD, but became less stable with further increase in the CD concentration in the film. From the isotherms for the inclusion of p-NP and 1-naphthoate (1-Naph) into the film, the inclusion (stability) constants were determined to be 3.7x10(3) M(-1) and 1.9x10(2) M(-1), respectively. These results show that the selective inclusion of CD is retained after preparation of the composite film.     

一种卤键高分子多层膜的层层组装及其稳定性的提高

设计合成了聚甲基丙烯酸2-(4-碘-2,3,5,6-四氟苯氧基)乙酯( PIPEMA)和聚甲基丙烯酸3-(3-吡啶基)丙酯( PPyPMA),经过层层组装和随后的紫外可见光谱的检验,发现可以在丙酮和丁酮中组装PIPEMA/PPyPMA卤键多层膜,但是当以四氢呋喃(THF)或氯仿为组装溶剂时未能获得多层膜.另外,在丁酮中...     

Analysis and regulation of unusual adsorption of phthalocyanine zinc(II) into a Nafion film as investigated by UV-vis spectroscopic techniques

Phthalocyanine zinc(II) (ZnPc) was found to be adsorbed well into a Nafion (Nf) film. The kinetic analysis suggested that the adsorption of ZnPc into the Nf film is controlled by its diffusion in the Nf film with a diffusion coefficient of D = 1.9 x 10(-6) cm(2) s(-1) that is higher than those (10(-9)-10(-12) cm(2) s(-1)) of cationic redox molecules in the Nf film by 3-6 orders of magnitude. The adsorption isothermal was analyzed by a Brunauer-Emmett-Teller (BET) equation suggesting multilayer adsorption of ZnPc into the film. The BET analysis provided the amount of ZnPc for monolayer adsorption (w(m) = 1.50 x 10(-7) mol cm(-2)), from which the effective area for the ZnPc adsorption was estimated to be larger by a factor of 1.7 x 10(3) than the Nf film area (1.0 cm(2)). The absorption spectra of a Nf film adsorbing ZnPc ((Nf/ZnPc)(ads) film) exhibited two broad absorption bands at 385 and 680-750 nm without any structural features, which is significantly different from the absorption spectra of either ZnPc solution in DMF or a (Nf/ZnPc)(mix) film prepared from a DMF solution containing Nf and ZnPc by solvent evaporation. This is ascribed to the formation of a ZnPc aggregate in the (Nf/ZnPc)(ads) film. Photoluminescence data for the (Nf/ZnPc)(mix) film suggested the presence of a ZnPc monomer and dimer at equilibrium in the film with a concentration of 0.1 M and that energy transfer occurs from the monomer to the dimer in excitation of the monomer (at lambda(ex) = 609 nm) to yield emission from the dimer. By contrast, photoluminescence data for the (Nf/ZnPc)(ads) film suggested that the excited ZnPc is self-quenched significantly by the formation of the ZnPc aggregate in the film. The lesser electroactivity of ZnPc in the (Nf/ZnPc)(ads) film compared with that in the (Nf/ZnPc)(mix) film could be ascribable to more difficult diffusion of ZnPc in the former film due to the formation of the ZnPc aggregate. The adsorption of ZnPc into the Nf film was significantly regulated by simple pretreatments of the Nf film such as immersion in solvents and storage under solvent vapors. The regulation was explained by controlled physical and chemical properties of a channel for mass and ion transport that is formed by sulfonate groups, countercations, and solvent molecules in the Nf film.     

Study on the enhancement of catalytic activity for hemoglobin by quinhydrone in poly(o-aminophenol) film

Hemoglobin (Hb) and quinhydrone (QHQ) were incorporated in poly(o-aminophenol) [o-AP, POAP] film by electropolymerization of o-aminophenol in a weak acid solution containing Hb and QHQ. The nonconducting polymer film was found to be nearly rigid by piezoelectric quartz crystal (PQC) impedance. Therefore, the thickness of the Hb-QHQ-POAP film was estimated as about 104 +/- 10 nm by quartz crystal microbalance (QCM). The QHQ mediation effects on the biomacromolecule Hb entrapped in the POAP film were investigated by using cyclic voltammetry, amperometric technique and kinetic study. Cyclic voltammograms showed that the redox peaks in the Hb-QHQ-POAP film are much more reversible than those in the Hb-POAP film. The response current of the Hb-QHQ-POAP film to H(2)O(2) was almost twice than that of the Hb-POAP film. The Michaelis-Menten constant and the activation energy of Hb in the Hb-QHQ-POAP film are 7.47 mM and 13.91 kJ/mol, respectively, both are smaller than that in the Hb-POAP film. These results showed that the immobilized Hb in POAP film exhibited higher catalytic activity to H(2)O(2) due to the mediation of QHQ.     

螺噁嗪化合物在丙烯酸聚氨酯清漆膜中的光致变色性能

制备了含有螺噁嗪(SO)化合物的紫外光固化丙烯酸聚氨酯清漆(UV-PUA)膜, 研究了SO在该清漆中的光致变色性能, 并与其在聚甲基丙烯酸甲酯(PMMA)中的光致变色性能进行了比较. 结果发现, 紫外光固化螺噁嗪丙烯酸聚氨酯清漆(UV-SO-PUA)膜在紫外光固化过程中逐渐由无色变为蓝色和紫色, 撤去紫外光源, 漆膜退色至粉色, 且固化后的漆膜在粉色和紫色之间可逆变化; 而SO-PMMA膜在无色和蓝色之间可逆变化. 紫外光激发的UV-SO-PUA膜的紫外-可见吸收光谱可见光区出现了明显的双重吸收峰(520和600 nm), 而在PMMA中仅出现单峰. SO开环体在UV-PUA 中室温稳定性优于其在ＰＭＭＡ中的稳定性. SO在UV-PUA膜中的抗疲劳性能与其在PMMA中相比显著提高, 紫外光照射16 h, UV-SO-PUA漆膜未出现疲劳现象. SO在UV-PUA膜中表现出了优良的光致变色行为.     

不锈钢上黑色钼盐转化膜的研究

用阴极电沉积法从钼酸盐和磷酸盐温和溶液中获得了黑色的不锈钢转化膜,该膜具有良好的热稳定性。电子能谱（ＸＰＳ和ＡＥＳ）分析表明,膜厚约为８２０ｎｍ,膜的表面铝以Ｍｏ（Ⅵ）存在,而在膜内则以Ｍｏ（Ⅵ）与Ｍｏ（Ⅳ）共存。从ＡＥＳ深度剥蚀曲线的组成恒定区求得膜的组成为：Ｏ５０．９％,Ｍｏ２９．４％,Ｐ１２．６％和Ｆｅ７．１％。循环伏安的氧化峰也证明膜内存在Ｍｏ（Ⅳ）。     

Immobilization and enzymatic activity of glucose oxidase on polystyrene surface modified with ozone aeration and UV irradiation in distilled water and/or aqueous ammonia solution

Adsorption condition and enzymatic activity of glucose oxidase (GOD) on polystyrene (PS) film surfaces modified with ozone aeration and UV irradiation (O3/UV) treatment were investigated. The total amount of GOD immobilized on the PS film modified with the O3/UV treatment in distilled water (PS-W film) was approximately twice as large as that on the film treated in an aqueous ammonia solution (PS-A film), whereas the specific activity of GOD on the PS-A film was four times higher than that on the PS-W film. In contrast, no enzymatic activity of GOD on the non-treated PS film was observed because of irreversible denaturation of the adsorbed GOD. We therefore conclude that the PS films modified by the O3/UV treatment in the aqueous media are effective in immobilizing GOD.     

聚乙烯醇缩丁醛LB膜制备及其对硬脂酸镉LB膜的修饰

研究了PVB单分子膜的π～A曲线和稳定性,沉积了优质LB膜,发现将PVB与CdSt₂形成交替异质的LB膜能提高膜的光学质量;在CdSt₂LB膜的上面封装PVBLB膜能保持CdSt₂LB膜的结构。     

Application of a surface plasmon resonance sensor to analyses of amine compounds with the use of a polymer film and an acid-base reaction.

A surface plasmon resonance (SPR) sensor was applied to analyses of some amine compounds (n-butylamine, isobutylamine, aniline, and N,N-dimethylaniline) by using a polymer film and an acid-base reaction in it. Poly(acrylamide) (PAA) was adopted as the polymer film and was immobilized on an Au film to prepare a sensor chip. Pivalic acid was entered into the PAA film as an acid. The PAA film with a thickness of 50 nm gave the highest sensitivity to the SPR sensor. Although water was better concerning the sensitivity for the SPR sensor as the solvent, ethanol was adopted because it dissolves well all of the amine compounds used. The Au film coated with the PAA film gave higher sensitivity for analyses of n-butylamine and isobutylamine, and lower sensitivity for analyses of aniline and N,N-dimethylaniline than an Au film without the PAA film. The PAA film containing pivalic acid gave 4-5 orders of magnitude higher sensitivity to the SPR sensor for analyses of all the amine compounds due to the reaction between pivalic acid and these amine compounds.