自活化乌拉草基多孔碳的制备和电化学性质

以乌拉草为原料,采用直接碳化方法,通过热解过程中前驱体自活化(即利用自身包含的活化剂实现分子内的化学活化),并经过必要的除杂过程制备了多孔碳材料Ula C-950-HF.测试了该多孔碳的电化学性质,并与以几种常见的生物质为原料制备的多孔碳材料及商用活性炭的电化学性质进行对比.结果表明,乌拉草基多孔碳材料Ula C-950-HF的电容值为113 F/g,经过4000次循环后,材料的电容值仅降低了4 F/g,显示出用作超级电容器电极材料的潜力.     

海藻基微孔碳材料的储甲烷性能

以天然海藻为原料,通过自活化制备了碳材料Sar CW-900-HF及Lam CW-900-HF,并对其进行表征和储甲烷能力测试.其比表面积分别为812和671 m~2/g,孔体积分别为0. 45和0. 44 cm~3/g,孔分布的峰值均在1. 1 nm,在室温及3. 5 MPa压强下储甲烷的能力分别为272 mg/g (质量比21. 3%)和246 mg/g (质量比19. 4%),经20 MPa压强压片后吸附甲烷体积比达到274和449 cm~3(STP)/cm~3,超过美国能源部提出的吸附剂的指标[263 cm~3(STP)/cm~3].     

基于ZIF-9的多孔碳对次甲基绿的吸附动力学研究

以含钴的类沸石咪唑酯骨架结构材料ZIF-9为模板,在氩气中进行碳化,以及在碳化时加入硫粉,分别得到含钴和钴硫双掺杂的多孔碳材料Co/C-700和CoS/C-700.对合成材料的结构和组成进行了PXRD、Raman光谱、SEM和氮气吸附脱附的表征,结果显示:合成材料保持了模板的骨架结构,比表面积分别为270.59和108.78 m~2·g~(-1),是微孔介孔碳纳米复合材料.Co/C-700和CoS/C-700对染料次甲基绿的最大吸附量分别为58.31和57.90 mg·g~(-1),吸附符合准二级动力学模型、孔扩散模型和Langmuir模型.分离、再生以及循环使用4次之后的Co/C-700对次甲基绿的吸附率仅下降了4%.     

由含铝金属有机骨架材料制备的多孔碳在锂硫电池中的应用

采用水热法制备了一种含铝金属有机骨架材料, 其在高温下发生炭化得到多孔碳, 最后与硫复合制得锂硫电池正极材料. XRD图谱显示在高温炭化时多孔碳样品出现了部分石墨化. N₂等温吸附-脱附测试分析显示合成的多孔碳材料含有微孔和介孔结构. 对不同载硫量的锂硫电池进行了充放电性能测试, 结果显示S质量分数为46.3%的样品在0.01 C倍率下首次放电容量达到1272 mA·h/g; 在0.1 C倍率下首次放电容量为934 mA·h/g, 循环性能良好.     

常温合成硫掺杂微孔碳及其二氧化碳的吸附性能

常温下以间苯三酚和3-甲醛苯并噻吩作为原料,一步法合成了含硫酚醛树脂。在氩气保护下碳化,成功制备出了硫掺杂多孔碳(S-PC)。并利用扫描电镜(SEM)、X射线光电子能谱(XPS)、X射线衍射(XRD)和氮气吸附-脱附仪对材料进行了形貌、结构和性能的表征。实验结果表明,所得样品具有较高比表面积和大量的微孔,经过调控,可以使制备的硫掺杂多孔碳的BET比表面积达到997 m2·g~(-1),并使其微孔孔体积达到0.44 cm3·g~(-1)。得益于较高的比表面积以及其富含微孔的特性,当材料应用于二氧化碳吸附时,具有较高的CO2吸附量,在273和298 K时分别高达5.13,3.22 mmol·g~(-1),并具有良好的选择性。     

兼具高孔隙率和梯度孔隙结构的多孔钯块材的制备、表征及其电化学性能研究

钯材料广泛用于氢同位素储存和分离、催化和传感等领域.传统的负载钯催化材料具有优异的乙醇和甲醇等电化学催化氧化性能.除此之外,负载钯催化材料还具有优异的甲烷催化燃烧性能.然而,很多研究显示负载钯催化材料存在很多不足,例如在工程应用过程中不稳定,纳米颗粒会发生聚集和长大,进而引起材料性能急剧下降等.不同于钯片、海绵钯粉末和负载钯催化材料,多孔钯具有三维连通的孔隙结构,可避免团聚现象的发生.同时,多孔钯还具有一些特殊的物理化学性能.研究表明,梯度孔隙结构是一种高效的电化学催化结构.因而近年来很多研究者都致力于探索具有高孔隙率和梯度孔隙结构多孔钯块材的制备方法.已有的研究包括造孔剂法和模板法等,但上述方法制得的多孔钯块材均存在比表面积低或难以获得块体材料缺点.我们研究组发展了一种制备兼具高孔隙率和梯度孔隙结构的多孔钯块材的新方法.即通过以一定粒度的NaCl颗粒作为造孔剂放电等离子烧结制备PdAl合金复合块材,然后通过去离子水溶解获得多孔PdAl合金,最后经过在盐酸溶液中去合金化得到具有数十微米的宏观大孔和约10纳米的纳米孔等梯度孔隙结构的多孔钯块材.当造孔剂添加量为20 vol.%,制得了孔隙率高达88%且完整的多孔钯块材.对该多孔钯块材的力学性能进行了测试,其压缩强度为0.5 MPa.对该块材进行氮吸附测试,测试结果显示其比表面积达到54 m2/g.我们进一步对该多孔钯块材的乙醇电化学催化氧化性能进行了研究.对不同扫描速度下多孔钯块材在KOH(1 mol/L)+乙醇(0.8 mol/L)溶液中电催化活性进行分析.随着扫描速率从10 mV/s提高到50 mV/s,正扫描峰电流密度也逐渐提高,且峰电位向正电位方向移动.对峰电流密度和扫描速率的平方根进行拟合,发现它们之间存在明显的线性关系,表明该电催化氧化行为是一个受扩散控制的过程.随着溶液中乙醇浓度不断增加,正扫描方向乙醇氧化峰的峰电流呈现出先增大后减小的趋势.这是因为乙醇基和羟基在钯表面的竞争性吸附造成的.当乙醇浓度较高时,乙醇基会占据钯表面大量的活性位,从而阻碍和抑制羟基的吸附.此时,羟基在钯表面的吸附成为电氧化反应的控制因素.因此,只有选择合适的乙醇浓度,才能更好地发挥材料的电催化性能.当乙醇浓度为2 mol/L时,峰电流最大,达到120 mA/cm2,表明多孔钯块材具有优异的电催化性能,这与该材料的梯度孔隙结构、高比表面积和高孔隙率密切相关.进一步对多孔钯块材的催化稳定性进行研究.该多孔钯块材显示出了优异的催化稳定性,当经过50次循环后,乙醇氧化峰的峰电流仅下降到~110 mA/cm2.     

甲烷在富纳米孔炭质吸附剂上的吸附

分析了以石油焦为原料采用复合活化工艺制备的吸附剂的孔结构特性。发现吸附剂微孔含量在90%以上并且主要集中于1 nm～2 nm之间，是富含纳米孔的吸附材料。甲烷在此吸附剂上的吸附研究表明，在25 ℃，3.5 MPa的条件下，甲烷质量吸附量超过14.0%；有效体积吸附量超过120?V/V(吸附甲烷的体积/容器的体积)。甲烷在富纳米孔炭质吸附剂上的等温吸附曲线表明，吸附类型属于Ⅰ类吸附，符合微孔填充理论；等压吸附曲线表明，低温有利于体积吸附量的增加；吸附剂中水分的增加对吸附有不利的影响。     

离子交换树脂基多孔碳材料的制备及其CO_2吸附性能研究

以废弃的阳离子交换树脂为原料,采用Zn Cl2活化法,在原料与活化剂质量比为1:2情况下,研究了不同的活化温度(300℃、400℃、500℃、600℃)对多孔碳材料孔隙结构和CO2吸附性能的影响。通过N2吸附脱附、扫描电子显微镜(SEM)、透射电镜(TEM)等对样品的孔隙结构和形貌进行了表征。采用变压吸附法,在常温常压下测试了样品对CO2的吸附性能,结果表明,随着活化温度的升高,多孔碳材料的比表面积、孔容、平均孔径等随之减小,当活化温度为400℃时,其微孔孔容比达到最大值49.6%,比表面积达到最大值1136 m2/g;当活化温度为600℃时,CO2吸附量达到了最大值9.2wt%(常温常压下),表明了CO2吸附量与比表面积大小无直接关系,受超微孔孔径分布的影响更大。     

兼具高孔隙率和梯度孔隙结构的多孔钯块材的制备、表征及其电化学性能研究（英文）

钯材料广泛用于氢同位素储存和分离、催化和传感等领域.传统的负载钯催化材料具有优异的乙醇和甲醇等电化学催化氧化性能.除此之外,负载钯催化材料还具有优异的甲烷催化燃烧性能.然而,很多研究显示负载钯催化材料存在很多不足,例如在工程应用过程中不稳定,纳米颗粒会发生聚集和长大,进而引起材料性能急剧下降等.不同于钯片、海绵钯粉末和负载钯催化材料,多孔钯具有三维连通的孔隙结构,可避免团聚现象的发生.同时,多孔钯还具有一些特殊的物理化学性能.研究表明,梯度孔隙结构是一种高效的电化学催化结构.因而近年来很多研究者都致力于探索具有高孔隙率和梯度孔隙结构多孔钯块材的制备方法.已有的研究包括造孔剂法和模板法等,但上述方法制得的多孔钯块材均存在比表面积低或难以获得块体材料缺点.我们研究组发展了一种制备兼具高孔隙率和梯度孔隙结构的多孔钯块材的新方法.即通过以一定粒度的NaCl颗粒作为造孔剂放电等离子烧结制备PdAl合金复合块材,然后通过去离子水溶解获得多孔PdAl合金,最后经过在盐酸溶液中去合金化得到具有数十微米的宏观大孔和约10纳米的纳米孔等梯度孔隙结构的多孔钯块材.当造孔剂添加量为20 vol.%,制得了孔隙率高达88%且完整的多孔钯块材.对该多孔钯块材的力学性能进行了测试,其压缩强度为0.5 MPa.对该块材进行氮吸附测试,测试结果显示其比表面积达到54 m~2/g.我们进一步对该多孔钯块材的乙醇电化学催化氧化性能进行了研究.对不同扫描速度下多孔钯块材在KOH(1 mol/L)+乙醇(0.8 mol/L)溶液中电催化活性进行分析.随着扫描速率从10 mV/s提高到50 mV/s,正扫描峰电流密度也逐渐提高,且峰电位向正电位方向移动.对峰电流密度和扫描速率的平方根进行拟合,发现它们之间存在明显的线性关系,表明该电催化氧化行为是一个受扩散控制的过程.随着溶液中乙醇浓度不断增加,正扫描方向乙醇氧化峰的峰电流呈现出先增大后减小的趋势.这是因为乙醇基和羟基在钯表面的竞争性吸附造成的.当乙醇浓度较高时,乙醇基会占据钯表面大量的活性位,从而阻碍和抑制羟基的吸附.此时,羟基在钯表面的吸附成为电氧化反应的控制因素.因此,只有选择合适的乙醇浓度,才能更好地发挥材料的电催化性能.当乙醇浓度为2 mol/L时,峰电流最大,达到120 mA/cm~2,表明多孔钯块材具有优异的电催化性能,这与该材料的梯度孔隙结构、高比表面积和高孔隙率密切相关.进一步对多孔钯块材的催化稳定性进行研究.该多孔钯块材显示出了优异的催化稳定性,当经过50次循环后,乙醇氧化峰的峰电流仅下降到~110 mA/cm~2.     

MOFs-多孔碳的制备及吸附性能研究

本文以均苯三酸和二水合醋酸锌为原料,分别用咪唑和2-甲基苯并咪唑作为为第二配体,在50℃条件下合成了两种金属有机框架结构MOFs-Im和MOFs-Me。氮气氛围中900℃煅烧得到多孔碳材料MOFs-Im-C和MOFs-Me-C。利用红外光谱仪、荧光光谱仪、同步热分析仪对配合物的结构、发光性以及热稳定性进行了表征;对煅烧后样品采用场发射扫描电子显微镜、比表面及孔径分析仪等进行表征,并通过对亚甲基蓝和罗丹明B的脱除来测试其吸附性能。结果表明,煅烧后生成的MOFs-Im-C多孔碳材料对亚甲基蓝的吸附率在120 nim时几乎达到100%,说明该多孔碳材料对亚甲基蓝具有较好的吸附性能。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.