SAPO分子筛的酸性及其孔道分布对丁烷异构脱氢反应的影响

 合成了四种磷铝及硅磷铝系列分子筛,并用XRD表征了分子筛的晶体结构,用X荧光光谱测定了其元素组成,用NH3－TPD和物理吸附考察了其酸性和孔道分布．考察了以合成的分子筛为基质制备的催化剂上丁烷异构脱氢反应的性能．结果表明,以弱酸性的SAPO－5分子筛和孔口狭窄的SAPO－34分子筛为载体的催化剂,它们的催化性能较差;以十元环的SAPO－11分子筛为载体的催化剂显示出较高的活性和选择性．同时,考察了不同分子筛催化剂上Pd金属粒子的分散状态,分析了分子筛的酸性和孔道结构对反应性能的影响．     

整体式 Cu-ZSM-5 催化剂上 NH3 选择性催化还原 NO 活性

 采用浸渍法制备了一系列不同 Cu 含量的 Cu-ZSM-5 催化剂, 并用于 NH₃ 选择性催化还原 (SCR)NO 反应. 结果表明, 当 Cu 含量为 8%时, Cu-ZSM-5 催化剂的活性最高; 当空速为 30 000 h^–1. , 在 198~440 ^oC 反应时 NO 转化率均高于 80%, 最高可达 97%, 且空速的影响较小. 经快速水热老化后, 该催化剂活性明显优于商用 V 基催化剂. H₂O 和 SO₂ 对 Cu-ZSM-5 催化剂的 SCR 活性有所影响, 但可明显恢复. X 射线衍射和 NH3 程序升温脱附结果表明, 当 Cu-ZSM-5 中 Cu 含量为 8% 时, 进入 ZSM-5 中阳离子位的 Cu 较多, 催化剂的活性较高, 且其表面具有较多的酸中心和酸量, 从而有利于 SCR 反应.     

SO42-/ZrO2固体超强酸酸性和烯烃烷基化催化性能之间的关系

本文研完了SO₄^2-/ZrO₂型固体超强酸酸性和烯烃烷基化催化性能之间的关系。得到了B酸量和L酸量之比(B/L)与酸强度、活性、选择性之间的相关性。当B/L值趋于2时,表现出最高的酸强度和最佳的催化活性与选择性。     

多级孔结构WO3/ZrO2固体酸催化剂的烷基化催化性能研究

采用复合模板表面活性剂辅助水热法一步合成WO3/ZrO2体系多级孔固体酸催化剂,探讨了煅烧温度对所合成催化剂试样酸强度及酸量的影响,并考察了催化剂针对苯和十二烯的烷基化反应中的催化性能.结果表明,WO3/ZrO2体系催化剂具有较强的酸强度,并且与催化剂的比表面积和晶化程度有密切关系,比表面积的增大和四方相ZrO2的生成能有效地提高催化剂的酸强度.该催化剂具有优良的烷基化反应催化活性和选择性,其中450℃,5h煅烧的WO3/ZrO2催化剂样品酸性最强,其烷基化催化活性和选择性最优.     

Dehydrogenation of Propane to Propylene in the Presence of CO2 over Steaming‐treated HZSM‐5 Supported ZnO

Dehydrogenation of propane to propylene over zinc oxide catalysts supported on steaming‐treated HZSM‐5 in the presence of CO₂ has been investigated. The highest catalytic performance can be achieved on the 5%ZnO/HZSM‐5(650) catalyst with the HZSM‐5 support steaming at 650°C, which allows the maximum propylene yields of 29.7% and 20.3% at the initial and steady states, respectively, in the catalytic dehydrogenation of propane at 600°C. The superior catalytic performance of this catalyst can be attributed to high dispersion of ZnO and appropriate Br?nsted acidity of the HZSM‐5(650) support. The catalytic stability is enhanced by the addition of CO₂ to the feed gas due to the suppression of coke formation.     

Citronellal cyclisation over heteropoly acid supported on modified montmorillonite catalyst: effects of acidity and pore structure on catalytic activity

Citronellal cyclisation to isopulegol is an important intermediate step in the production of menthol. Several heteropoly acids (PTA) supported on modified montmorillonite (MM) catalysts were synthesized and then tested in cyclisation reactions. The prepared samples were characterized by XRD, ICP-OES, FTIR, N₂ sorption, NH₃-TPD, pyridine adsorption, amine titration and FE-SEM techniques. Effects of post-treatment were studied on montmorillonite pore structure, acidity and catalytic activity. The catalytic activity and isopulegol selectivity improved with acid-treatment and PTA loading. The amount of Lewis acidity of montmorillonite was enhanced with acid-treatment and PTA impregnation. In cyclisation, highest catalytic activity (31.87 mmol cat g^?1 min^?1) was achieved with 96% isopulegol yield in the use of 20% PTA-MM catalyst. The highest catalytic activity and selectivity were obtained in the presence of higher acidity and strong Lewis acidic sites, whereas effects of pore structure blockage seemed minor. The catalytic activity further decreased with the loss of active acidic sites (L and B) due to PTA decomposition with calcination at a higher temperature.     

Zn/SiO_2气相催化裂解1,1,2-三氯乙烷脱HCl:酸性与失活

用浸渍法制备了一系列SiO_2负载的过渡金属催化剂M/SiO_2(M为第Ⅳ周期过渡金属),用于气相催化裂解1,1,2-三氯乙烷(TCE)脱HCl的反应。研究发现,在M/SiO_2催化剂中,Zn/SiO_2催化性能最好,TCE转化率能达到98%,顺-1,2-二氯乙烯(cis-DCE)的选择性为82%。随着Zn负载量的增加,Zn/SiO_2催化剂上TCE转化率逐渐增加,与催化剂上总酸量变化一致。将总酸量以Zn负载量归一化得到比酸量,则比酸量越大,Zn/SiO_2催化剂比活性越高,表明Zn/SiO_2催化剂表面酸性中心是TCE脱氯反应的活性中心。Zn/SiO_2催化剂在TCE脱HCl反应中存在一定的失活现象,归因于反应过程中催化剂表面积炭。低Zn负载量催化剂上会产生较多积炭,归因于其具有较多强酸性中心,表明催化剂表面强酸中心是导致催化剂积炭和失活的主要原因。     

Hydrogenative Ring-Rearrangement of Furfural to Cyclopentanone over Pd/UiO-66-NO2 with Tunable Missing-Linker Defects

Upgrading furfural (FAL) to cyclopentanone (CPO) is of great importance for the synthesis of high-value chemicals and biomass utilization. The hydrogenative ring-rearrangement of FAL is catalyzed by metal-acid bifunctional catalysts. The Lewis acidity is a key factor in promoting the rearrangement of furan rings and achieving a high selectivity to CPO. In this work, highly dispersed Pd nanoparticles were successfully encapsulated into the cavities of a Zr based MOF, UiO-66-NO₂, by impregnation using a double-solvent method (DSM) followed by H₂ reduction. The obtained Pd/UiO-66-NO₂ catalyst showed a significantly better catalytic performance in the aforementioned reaction than the Pd/UiO-66 catalyst due to the higher Lewis acidity of the support. Moreover, by using a thermal treatment. The Lewis acidity can be further increased through the creating of missing-linker defects. The resulting defective Pd/UiO-66-NO₂ exhibited the highest CPO selectivity and FAL conversion of 96.6% and 98.9%, respectively. In addition, the catalyst was able to maintain a high activity and stability after four consecutive runs. The current study not only provides an efficient catalytic reaction system for the hydrogenative ring-rearrangement of furfural to cyclopentanone but also emphasizes the importance of defect sites.     

Pt-Gd/KL和Pt/GdKL分子筛的重整催化活性中心研究

通过把Ｇｄ引入Ｐｔ／ＫＬ分子筛单功能重整催化剂，研究ＰｔＧｄ／ＫＬ和Ｐｔ／ＧｄＫＬ分子筛的重整反应性能和活性中心以及催化剂的表面酸碱性。结果表明，Ｇｄ的引入方式和引进量对催化重整反应有明显影响。共浸法制备的催化剂ＰｔＧｄ／ＫＬ，其芳构活性比离子交换法制备的催化剂Ｐｔ／ＧｄＫＬ高，Ｇｄ含量为０１％的Ｐｔ０１Ｇｄ／ＫＬ芳构活性最好。弱酸性和弱碱性物质以及硫化物对ＰｔＧｄ／ＫＬ和ＰｔＧｄＫＬ催化重整反应的影响Ｇｄ小于不含Ｇｄ的Ｐｔ／ＫＬ。Ｇｄ对催化重整反应有两方面影响：其一是与金属Ｐｔ相互作用增加活性中心、加强金属功能；其二是增加催化剂的酸性和裂解产物，降低芳构选择性。     

负载铂催化剂中沸石载体酸性对甲烷两步转化的影响

考察了具有相同金属分散度的Pt/NaY、Pt/HNaY、 Pt/HY、Pt/NaBeta和Pt/HBeta催化剂中沸石载体的酸性对在低温下（≤250 ℃）甲烷两步等温转化反应以及由甲烷解离吸附产生的表面碳物种分布的影响。由甲烷等温两步转化生成的C2+烃类产物的总量随着载体酸性的增加而明显增加;C2～C6产物的分布也发生了变化。由表面碳物种的程序升温加氢结果表明,在各种催化剂上碳物种的形式是相似的,其总量和具有活性的Cα物种的量均因载体酸性增加而增加,反应性也增大。这种因沸石载体酸性变化而引起的载体效应是由金属和载体的相互作用造成负载在酸性载体上铂粒子的贫电子性而引起,即由金属粒子电子性质的变化而引起的催化性质的变化。     

The Influence of Carbon Nature on the Catalytic Performance of Ru/C in Levulinic Acid Hydrogenation with Internal Hydrogen Source

The influence of the nature of carbon materials used as a support for Ru/C catalysts on levulinic acid hydrogenation with formic acid as a hydrogen source toward gamma-valerolactone was investigated. It has been shown that the physicochemical properties of carbon strongly affect the catalytic activity of Ru catalysts. The relationship between the hydrogen mobility, strength of hydrogen adsorption, and catalytic performance was established. The catalyst possessing the highest number of defects, stimulating metal support interaction, exhibited the highest activity. The effect of the catalyst grain size was also studied. It was shown that the decrease in the grain size resulted in the formation of smaller Ru crystallites on the catalyst surface, which facilitates the activity.     

焙烧温度对甲硫醇催化剂K_2WO_4/Al_2O_3结构和性能的影响

研究了焙烧温度对溶胶-凝胶法制备的甲硫醇催化剂K2WO4/Al2O3的表面结构和催化性能的影响.表征结果显示,K2WO4在Al2O3上分散得较好,在450和550oC焙烧的催化剂颗粒大小均匀,无明显团聚现象.随着焙烧温度的升高,催化剂的比表面积减小,表面钨物种与Al2O3的相互作用减弱,与碱物种的相互作用增强,酸碱强度降低.K2WO4/Al2O3表面不含质子酸.催化剂活性与其比表面积及表面的共轭酸碱对密切相关.评价结果表明,在550oC焙烧而制得的催化剂活性最高.     

PtZn-Sn/SBA-15合成、表征及对丙烷催化脱氢性能

以SBA-15为载体,利用浸渍法制备了单、双和三金属Pt催化剂,并对催化剂进行了N2物理吸附(BET)、程序升温还原(H2-TPR)、H2-化学吸附、透射电子显微镜(TEM)和O2-脉冲等技术表征,研究了它们对丙烷催化脱氢(CDH)制丙烯反应的催化性能。研究结果表明,Pt在三金属催化剂中的分散性能最好,并且部分负载组分可以进入SBA-15的孔道,Pt的分散度达到29%,Pt粒子尺寸为3 nm左右。三金属催化剂表现出优越的脱氢性能,这主要归结于载体的弱酸性、活性组分和助剂、载体之间的相互作用及Zn对Pt的电子调控作用。这些因素使催化剂的积炭量较低,因而具有较高的脱氢稳定性和极高的选择性。     

Coking kinetics and influence of reaction-regeneration on acidity,activity and deactivation of Zn/HZSM-5 catalyst during methanol aromatization

The coking kinetics and reaction-regeneration on Zn/HZSM-5(Zn/HZ) catalyst in the conversion of methanol to aromatics were investigated.The highest initial benzene, toluene and xylene(BTX) yield of ca. 67.7% was obtained on fresh Zn/HZ catalyst, which showed the worst catalytic stability. The cycle of reaction-regeneration significantly modified the texture and acidity of Zn/HZ catalyst, which in turn affected its catalytic performance and coking behavior in methanol conversion to BTX. The residual carbon located on the surface of Zn/HZ catalyst led to the decrease of acid sites and the change on the acid sites distribution, which played an important roles on its activity and deactivation. It was found that the high B/L ratio and the low total acid sites concentration of the Zn/HZ catalyst favored to the high BTX yield and good catalytic stability in methanol conversion.     

含锌尖晶石型ZnM_2O_4(M=Cr,Al,Fe)催化剂上二氯甲烷高效催化燃烧

采用溶胶凝胶法制备出一系列的含锌尖晶石型ZnM_2O_4(M=Cr,Al,Fe)催化剂并测试其对二氯甲烷催化燃烧性能,并对催化剂进行了XRD,H_2-TPR,NH_3-TPD和XPS等表征.制备出的催化剂都具有较高的反应活性,其中ZnCr_2O_4尖晶石活性最佳,其T50为277℃.表征结果表明,催化剂的性能受到表面酸性和氧化还原性的协同作用.ZnCr_2O_4尖晶石催化剂具有较小的中等酸强度的表面酸性和最佳的低温还原性能,因此反应性能最佳.     

改性菱铁矿催化剂的催化脱硝活性及抗硫性研究

采用混合搅拌法制备了Ce、Zr掺杂改性的菱铁矿SCR脱硝催化剂,研究了Ce、Zr共同掺杂对催化剂催化脱硝性能及抗硫性的影响。结果表明,3%Ce+3%Zr掺杂菱铁矿催化剂(Ce_(0.03)/Zr_(0.03)-菱铁矿)具有优异的催化脱硝活性,在180-330℃,催化脱硝效率均在92%以上,该催化剂同时具有良好的抗SO_2性能,在210℃下通入体积分数为0.01%的SO_2,8 h后仍有95%以上的催化脱硝效率。通过XRF、BET、XRD、NH_3-TPD、TG等实验手段对催化剂成分、微观孔结构、晶相等进行表征。表征结果显示,Ce、Zr的掺杂能明显提高催化剂的比表面积以及表面结晶分散度,增强催化剂的表面酸性,促进硫酸铵盐在催化剂表面的分解。因此,催化剂具有优异的中低温催化脱硝活性及抗硫性。     

DRIFT Study on Cr2O3-SO42-/TiO2 Catalyst for Low Temperature Selective Catalytic Reduction of NO with NH3

Chromium oxides supported on TiO2 showed good activity for the selective catalytic reduction of NO by NH3.The catalytic activity of Cr2O3-SO42-/TiO2 catalyst was greatly enhanced by the addition of SO42-into TiO2 support.The catalyst surface properties were characterized with NH3-TPD（temperature programmed desorption） and H2-TPR（temperature programmed reduction）.The sulphate on the catalyst surface could enhance the acidity and redox of the catalyst obviously.The reaction mechanism on this catalyst was researched in detail by in situ diffuse reflectance Fourier transform infrared（FTIR） spectroscope.Eley-Rideal and Langmuir-Hinshelwood mechanism existed simultaneously for selective catalytic reduction（SCR） reaction of NO over Cr2O3-SO42-/TiO2 catalyst.     

固体酸催化剂上的甲苯硝化反应

研究了ＨＭ，ＨＺＳＭ－５和其它几种固体酸催化剂上的甲苯硝化反应，发现高硅铝比ＨＺＳＭ－５沸石的活性及对位选择性最高，甲苯转化率达６５％，ｐ／ｏ比达０．７８．通过考察沸石晶粒大小、酸性强弱、脱铝程度和阳离子交换等因素对反应活性和选择性的影响，发现该反应主要在沸百孔内进行，对位选择性与沸石的孔径存在一定对应关系．沸石催化剂除能促进ＨＮＯ３解离成ＮＯ外，对甲苯也有活化和富集作用，因而反应活性与催化剂的酸性有关，适当增加沸石的亲油性也有利于提高硝化反应活性．     

载体酸性对Mo/HZSM-5-Al2O3催化剂上烯烃歧化反应性能的影响

在固定床反应器上考察了Mo/HZSM-5-Al2O3催化剂上乙烯与2-丁烯歧化制丙烯反应的性能.结合X射线衍射、NH3程序升温脱附、吡啶吸附红外光谱、H2程序升温还原和程序升温氧化等表征结果发现,载体酸性的差异导致催化剂酸性和 Mo物种落位方式不同.载体酸性较强时,催化剂积炭严重,反应稳定性差;载体酸性较弱时,Mo物种...     

载体和担载酸对乙烯直接氧化合成乙酸反应的影响

 在固定床流动反应器上研究了Pd－酸／载体体系催化乙烯直接氧\r\n化合成乙酸的反应，并对载体相同但担载酸强度不同的催化剂的催化活\r\n性进行了比较．结果表明，担载酸的强度明显影响催化剂的活性，酸强\r\n度越大其催化活性越高．用NH3－TPD和异丙醇脱水探针反应表征了二氧\r\n化硅、活性碳和酸性白土三种载体担载的Pd－H4SiW12催化剂的酸性，\r\n并测试了三种催化剂的催化活性．结果表明，载体通过影响担载酸的强\r\n度而影响催化剂的活性，载体上的强酸中心越多，催化剂的活性越高．\r\n测定了二氧化硅、活性碳和酸性白土三种载体担载的Pd－H4SiW12催化\r\n剂上Pd的分散度，并与其催化活性相关联．结果表明，决定乙烯直接氧\r\n化生成乙酸反应活性的主要因素是催化剂的酸强度而不是Pd的分散度．