非掺杂型高效绿色磷光有机电致发光器件

在空穴传输层TCTA与电子传输层TPBi之间引入磷光染料Ir(ppy)3超薄发光层,制备了结构为ITO/MoO_3(2 nm)/NPB(40 nm)/TCTA(10 nm)/Ir(ppy)3(xnm)/TPBi(40 nm)/LiF(1 nm)/Al(80 nm)的非掺杂磷光有机电致发光器件。通过调控非掺杂发光层的厚度,详细研究了Ir(ppy)3层厚度对器件性能的影响。实验结果表明,当非掺杂发光层厚度为0.2 nm时,器件的性能最好,器件的亮度、效率和外量子效率分别达到26 350 cd·m~(-2)、42.9 cd·A~(-1)和12.9%。研究结果表明,采用超薄的非掺杂发光层可以简化器件结构和制备工艺,获得高效率的OLED器件。     

高效率和色稳定性的双超薄发光层的黄光有机电致发光器件

主要对rubrene黄光发光材料制作0.1nm厚度的超薄发光层的有机电致发光器件作了研究,并配合BCP空穴阻挡层探讨了对器件效率和色坐标稳定性的影响。双超薄rubrene发光层配合BCP空穴阻挡层的有机电致发光器件的性能得到了很好的改善,外加电压6V时,器件电流效率为6.35cd.A-1;外加电压10V时,器件发光亮度达到了7068cd.m-2。另外,在较大的外加电压驱动范围内,器件的色坐标一直保持在(0.49,0.49)。增加的发光效率和良好的色坐标稳定性主要是取决于空穴与电子的注入与输运平衡以及激子在超薄rubrene发光层中稳定性的复合平衡。     

BPhen作为发光层间隔层对黄光OLED的影响

使用R-4B和GIrl作为磷光掺杂剂、CBP为主体、BPhen为发光层间隔层,制备了包含红、绿双发光层的黄色磷光OLED器件。器件结构为ITO/Mo O3(40 nm)/NPB(40 nm)/TCTA(10 nm)/CBP∶GIrl(14%)(20nm)/BPhen(x nm)/CBP∶R-4B(6%)(10 nm)/BCP(10 nm)/Alq3(40 nm)/Li F(1 nm)/Al(1 000 nm)。BPhen位于两发光层之间,具有调节载流子复合的功能,其中x为BPhen的厚度。通过调整x的值,研究了BPhen厚度对OLED器件发光性能的影响。实验结果表明,适当厚度的BPhen层可以提高器件的发光亮度和电流效率。BPhen厚度为6 nm的器件性能最佳,16 V驱动电压下的器件亮度最高可达11 270 cd/m2,最大电流效率为24.35 cd/A,而且绿光和红光波峰强度相近,黄光颜色纯正,色坐标趋近于(0.5,0.5)。     

Nondoped-type White Organic Light-Emitting Diode Using Star-Shaped Hexafluorenylbenzene as an Energy Transfer Layer

采用真空蒸镀的方法以星形六苯芴类新材料1,2,3,4,5,6-hexakis(9,9-diethyl-9H-fluoren-2-yl)benzene(HKEthFLYPh)作为能量传输层制备了indium-tin-oxide(ITO)/N,N′-bis-(1-naphthyl)-N,N′-diphenyl-(1,1'-biphenyl)-4,4′-diamine(NPB)/HKEthFLYPh/5,6,11,12-tetraphenylnaphtacene(rubrene)/tris(8-hydroxyquinoline) aluminum (Alq3)/Mg:Ag的白色有机电致发光器件. NPB和Alq3分别作为蓝色发光层和电子传输层,NPB和Alq3之间的超薄Rubrene层 作为黄色发光层. 结果表明,超薄rubrene层改善了白光器件的色纯度与稳定性,器件的光谱及色坐标几乎不随驱动电压的变化而改变.当rubrene层厚度为0.3 nm时,器件的Commissions Internationale De L′Eclairage (CIE)色坐标为(0.32,0.33). 驱动电压为18 V时,器件的最大亮度为4816 cd/m2.     

有机层厚度变化的有机电致发光器件与微腔器件光谱分析

设计中心波长为520nm,改变有机层厚度,即空穴传输层NPB和发光层Alq3的厚度,分别由10nm逐渐增加至100nm,器件的总体厚度也随着改变,分别计算模拟出有机电致发光器件(OLED)和微腔有机电致发光器件(MOLED)的电致发光谱(EL),并对光谱的积分强度、峰值强度、半峰全宽、峰值位置的三维分布图进行比较分析。综合考虑光谱的峰值位置(中心波长)、最大的峰值强度和积分强度(与亮度、效率相关)、最小半峰全宽(色纯度高)进行合理的设计,可以找到最佳厚度。发现:NPB和Alq3的厚度分别为70和62nm时,器件性能最佳,并且微腔器件的结果尤为明显。结果表明,通过模拟计算,可以深入探索MOLED和OLED发光特性,设计出合理的器件结构。     

红色磷光微腔有机电致发光器件的发光性能

制备了结构为G/DBR/ITO/Mo O3(1 nm)/Tc Ta(55 nm)/CBP∶Ir(piq)2acac(44 nm,6%)/TPBI(55nm)/Li F(1 nm)/Al(80 nm)的红色磷光微腔有机电致发光器件(MOLED),同时制作了无腔对比器件OLED,研究微腔结构对磷光器件发光性能的影响。研究发现,OLED的电致发光(EL)峰值为626 nm,半高全宽(FWHM)为92 nm;MOLED的发光峰值为628 nm,FWHM为42 nm,窄化了1/2。MOLED的最大亮度、最大电流效率、最大外量子效率(EQE)分别为121 000 cd/m2、27.8 cd/A和28.4%,OLED的最大亮度、最大电流效率、最大EQE分别为54 500 cd/m2、13.1 cd/A和16.6%。结果表明,微腔器件的发光性能与无腔器件相比得到了较大幅度的提升。     

电场变化对有机磷光器件中激子形成影响的研究

激子形成区域随电场变化的移动会使得有机电致发光器件(OLEDs)的效率和色度发生改变,从而影响器件的性能。文章首先制备了两种OLED器件,器件1为ITO/PEDOT∶PSS/PVK∶Ir(ppy)₃∶DCJTB (100∶2∶1 wt)/BCP(10 nm)/Alq₃(15 nm)/Al,器件2为ITO/PEDOT∶PSS/PVK∶Ir(ppy)₃(100∶2 wt)/BCP(10 nm)/Alq₃(15 nm)/Al,研究了电场强度对单层多掺杂结构器件激子形成的影响。实验发现在多掺杂发光层中,随着电压的增加,Ir(ppy)₃,PVK和DCJTB的发光均增强,PVK和DCJTB发光增强更快。对其发光机制进行分析,认为较高电场下,载流子获得较高能量,更容易形成高能量激子,产生宽禁带材料PVK的发光;另一方面,从能级结构分析DCJTB的带隙较窄, 俘获更多的载流子发光更强。同时,在器件的电致发光(EL)光谱发现在460 nm处一新的发射峰, 发光随着电压的增大相对减弱。为了研究460 nm发光的来源,制备了器件：ITO/PEDOT∶PSS/PVK∶BCP∶Ir(ppy)₃(x∶y∶2 wt)/Alq₃(15 nm)/Al, 改变x, y的比值研究发现,460 nm处的发光依然存在,推测此发光峰应与PVK及BCP之间有关。     

TCTA对红绿磷光有机电致发光器件发光层激子的调控作用

制备了结构为ITO/MoO3(50 nm)/NPB(40 nm)/TCTA(10 nm)/CBP:14%GIr1(30 nm)/TCTA(x)/CBP:2%R-4B(10 nm)/BCP(10 nm)/Alq3(40 nm)/LiF(1 nm)/Al(100 nm)的红绿磷光有机电致发光器件,GIr1和R-4B分别为红、绿磷光染料。通过在红绿间插入较薄间隔层TCTA的方法,调节载流子、激子在红绿发光层中的分布,并结合TCTA和BCP对发光层内载流子和激子的有效阻挡作用,研究了载流子调控层TCTA在不同厚度下对器件发光性能的影响。结果表明,TCTA为1 nm时,器件的发光性能得到了很好的提升。电压为6 V时,TCTA为1 nm器件的电流密度、亮度、最大电流效率分别为0.509 mA/cm2、69.91 cd/m2和13.72 cd/A,而TCTA为0 nm器件的电流密度、亮度、最大电流效率分别为1.848 mA/cm2、215.7 cd/m2和11.67 cd/A。     

基于PVK∶NPB掺杂体系的有机电致发光器件的性能

利用溶液旋涂的方法,通过改变复合功能层中poly(N-vinylcarbazole)(PVK)和N,N′-bis-(1-naph-thyl)-N,N′-diphenyl-(1,1′-biphenyl)-4,4′-diamine(NPB)的质量比,制备结构为indium-tin-oxide(ITO)/PVK:NPB/2,9-dimenthyl-4,7-diphenyl-1,10-phenanthroline(BCP)/Mg:Ag的有机电致发光器件,并对器件的电致发光特性进行了表征。研究结果表明,当复合功能层中PVK和NPB的质量比为1:1时器件性能最好,在该器件的电致光谱中,除了NPB的本征谱峰外,在长波方向还出现了一个位于640nm处的谱峰,这是PVK和NPB产生的电致激基复合物发光,并且随着驱动电压的增加,电致激基复合物的发光强度也相对增强。     

LiF超薄层引起的OLEDs发光光谱展宽

将LiF插入到发光层Alq₃中,制备了有机电致发光器件(OLED),其器件的结构为:ITO/NPB (45 nm)/Alq₃ (x nm)/LiF (0.3 nm)/Alq₃ /Al(150 nm)。发现器件的电致发光谱(Electroluminescence spectra, EL)有非常明显的展宽现象,这为白光器件的制备提供了一条简单的途径。通过对比LiF在Alq₃中不同厚度处的发光谱,发现在x=10时谱线展宽最显著,器件最大亮度在22 V时达到8 260 cd/m²,最大效率可达 4.83 cd/A,并对其光谱展宽的机理及器件特性进行了分析。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.