MCM-41分子筛的改性、表面结构与吸附性质的研究

用三甲基氯硅烷、二甲基二氯硅烷、甲基三氯硅烷、四氯化硅与甲基碘改性高硅MCM-41中孔分子筛。XRD,^2^9SiMASNMR,^1^3CMASNMR,以及N~2、水与环己烷吸附的表征,显示改性不同程度地改变了分子筛的表面组成与结构,减小孔径,增加孔壁厚度,因而影响吸附行为,减小吸附容量。硅烷化减少了MCM-41的表面硅羟基含量,增加其疏水性。用CH~3I改性使孔径减小1.4nm,而硅羟基含量并未显著减少。硅烷化以及用CH~3I改性可提高MCM-41分子筛的热稳定性。SiCl~4的改性作用相对不明显。样品的水及环己烷吸附容量与其表面硅羟基含量呈现不同的线性关系,揭示高硅MCM-41分子筛表面吸附中心的本性。     

四甲基锡在MCM-41分子筛表面的接枝反应及产物性能

研究了真空条件下SnMe4在MCM-41分子筛表面的接枝反应，并用元素分析、ICP、GC-MS、XRD、FTIR、DRS、13C及119Sn MAS NMR、XPS、BET、TPD、TPR等方法对产物的组成、结构和性质进行了表征.结果表明, 两者可以定量地进行化学反应，将确定数目的甲基锡基团接枝在分子筛表面, 形成SnMe3/MCM-41物种；接枝反应发生在分子筛表面上, 不破坏MCM-41分子筛骨架结构；改性分子筛的BET比表面积有所降低，孔体积变小, 表面性质发生变化.四甲基锡在MCM-41上接枝反应的温度为343 K,比它与HY沸石的反应温度(193 K)高得多，并且产物SnMe3/MCM-41的热稳定性也高于SnMe3/HY.     

不同硅烷对HMS介孔分子筛甲基接枝的对比研究

通过气相沉积法,分别用三甲基氯硅烷(TMCS)和六甲基二硅氮烷(HMDSZ)对HMS介孔分子筛表面进行甲基接枝改性;分别采用XRD、N2-吸附、FTIR、29SiNMR和TG等手段对样品进行表征,并测定了样品的亲水性能.结果表明,两种硅烷都可以在HMS表面接枝,接枝后分子筛的介孔结构依然保持;但是,HMDSZ的接枝效果...     

纯硅MCM-48的合成研究

以正硅酸乙酯为硅源,非离子型表面活性剂聚乙二醇辛基苯基醚和阳离子型表面活性剂十六烷基三甲基溴化铵为共模板水热法合成了纯硅MCM-48分子筛。利用范德华力和氢键,聚乙二醇辛基苯基醚不仅可降低合成MCM-48所需阳离子表面活性剂的用量,而且有利于制备有序性好和稳定性高的MCM-48;并与单一阳离子表面活性剂制备的MCM-48的稳定性进行比较。     

茂锆金属配合物在介孔分子筛MCM-41上的接枝研究

茂锆金属配合物在介孔分子筛MCM-41上共价接技的合成和表征研究，以纯硅的MCM-41为载体，首先用四氯化硅与之反应在MCM-41的表面生成一定量的Cl：Si-OSi(O—Si≡)3基团，然后再用过量的三甲基氯硅烷保护分子筛表面剩余的硅羟基，接下来再让所得材料依次和环戊二烯基钠、正丁基锂、四氯化锆反应，从而通过在同一个反应瓶中经过五步连续合成的方法，得到了二氯二茂锆共价接枝于介孔分子筛MCM-41表面的有机无机复合材料．用XRD、^29Si和^13C MAS NMR、氮气吸附-脱附孔径分析、IR光谱等手段对所得样品进行了表征，并与用担载方法获得的二氯二茂锆固载化于MCM-41之中的样品进行了对比分析研究．     

苯基化纳米MCM-41材料的制备与表征

以苯基三甲氧基硅烷为偶联剂对纳米MCM-41分子筛进行了有机改性,制备了苯基改性的纳米MCM-41分子筛MCM-41(m)。利用元素分析、粉末XRD、傅里叶变换红外光谱、氮气吸附-解吸附、扫描电镜和差热-热重分析对制备产物进行了表征。粉末XRD结果表明,改性过程中,分子筛骨架未被破坏,并且所制备MCM-41(m)分子筛结晶度依然很高;傅里叶变换红外光谱表明苯官能团已经成功地接枝到了分子筛的孔道表面,且所得产物的骨架依然完好;低温氮气吸附-解吸附分析结果表明,MCM-41(m)分子筛孔道具有高度有序性,改性的纳米MCM-41分子筛孔道内的硅羟基与苯基三甲氧基硅烷发生了硅烷化反应,苯基成功地接枝到了分子筛的孔道表面。扫描电镜结果表明, 制得的苯基改性纳米MCM-41平均尺寸为110 nm。差热-热重分析结果说明了所制备的苯基化的纳米MCM-41样品具有良好的热稳定性,骨架稳定温度为823 ℃。苯基化的纳米MCM-41材料具有作为催化剂材料的潜在应用前景。     

介孔分子筛MCM-41的硅烷化改性及吸附性能研究

高硅分子筛MCM-41具有均匀的中孔孔径分布、较大的比表面积(>900m2/g)[1-2],应用前景广阔.已在硅基分子筛的基础上合成了各种含有杂原子分子筛、金属氧化物分子筛、有机官能团分子筛[3-8].改变介孔MCM-41分子筛的表面组成可以较好地调节其吸附性能[9].本文以直接反应的方法用三甲基氯硅烷来修饰MCM-41.通过XRD、红外吸收光谱和比表面和孔隙率测定对样品进行了表征,并分别对改性前后样品进行了水与苯的吸附性能研究.     

MBA接枝聚丙烯微孔膜的亲水改性研究

运用表面吸附法使聚丙烯微孔膜表面覆盖上引发剂,然后浸入氮氮亚甲基双丙烯酰胺(MBA)水溶液在一定温度下进行接枝反应。研究了引发剂用量,单体浓度,反应时间与温度对接枝率的影响,并用红外、扫描电镜对聚丙烯膜接枝前后的微孔膜进行了表征。同时对膜的亲水性和水通量进行了测试,发现其亲水性能有了极大的提高,其中接枝改性后接触角与未接枝的相比降低了90°以上,吸水率最多提高了12%,但是水通量有所下降。还对改性微孔膜的抗污染性能进行了探究。     

表面富锡MCM-41分子筛的表面金属有机化学制备及其对苯酚羟基化催化反应性能研究

采用SnBu₄在MCM-41表面的接枝反应和后续处理制备出了一种只在表面含锡的MCM-41型介孔分子筛。通过与采用纳米SnO₂和MCM-41机械混合法、SnCl₄浸渍法、水热合成法等制备的具有相当硅锡比(Si/Sn≈100)的SnMCM-41分子筛进行结构和对苯酚羟基化反应催化性能的比较发现， 由该法所得分子筛的水热稳定性明显提高，并在苯酚羟基化反应中表现出优良的催化活性、选择性和过氧化氢利用率。本文还详细考察了该催化剂对苯酚羟基化反应的最佳反应条件。     

沸石表面有机金属化学ZSM-5外表面上——Ge(n-C4H9)x基团的接枝及其性质研究

用气体分析及IR,NMR和元素分析等方法研究了真空系统中230℃和280℃下四丁基锗在ZSM-5沸石表面上的接枝反应,并对所得沸石的热稳定性和吸附性质进行了表征,与作者曾报道的硅胶及丝光沸石上的反应类似,四丁基锗也能与ZSM-5沸石表面上的硅羟基发生缩合反应,在其外表面或孔口生成组成为(=Si-O)xGe(n-C4H9)4-x(x=2~3)的表面有机锗化合物,在２３０℃接枝丁基锗基团不影响沸石的结构和表面积,仅改变它的孔口大小,在改性后的沸石上,Ｎ２的吸附性质没有改变,而不同分子尺寸的烃,加正已烷,２-甲基戊烷,２,３-二甲基丁烷却呈现出完全不同于起始ＺＳＭ-５沸石的择形吸附效应.     

硅烷化对Ti/HMS分子筛催化性能的影响

分别用水热法和气相沉积法制备了Ti/HMS分子筛,采用三甲基氯硅烷(TMCS)和六甲基二硅氮烷(HMDSZ)对Ti/HMS样品进行了气相硅烷化,并用X射线衍射、N2吸附、红外光谱、29Si核磁共振和紫外-可见光谱对样品进行了表征.丙烯环氧化反应的测定结果表明,硅烷化可显著提高环氧化催化活性.水热法制备的Ti/HMS经HMDSZ硅烷化后的催化活性比经TMCS硅烷化后的稍高;气相沉积法制备的Ti/HMS经HMDSZ硅烷化后的催化活性远高于经TMCS硅烷化后的催化活性.这是由于TMCS不但能与分子筛表面的硅羟基反应,而且能破坏分子筛骨架中的Si-O-Ti甚至Si-O-Si键,形成新的羟基,导致样品的亲水性较强,同时还能对气相沉积法制备的Ti/HMS中的四配位骨架钛产生破坏作用.     

Postsynthesis vapor-phase functionalization of MCM-48 with hexamethyldisilazane and 3-aminopropyldimethylethoxylsilane for bioseparation applications

MCM-48 was surface modified via vapor-phase reactions with hexamethyldisilazane (CH(3)-MCM-48) and 3-aminopropyldimethylethoxysilane (NH(2)-MCM-48). (29)Si NMR confirmed that the resulting materials contained covalently attached trimethylsilane and 3-aminopropyldimethylsilane moieties, both important functionalities for bioseparation applications. The surface coverage was approximately 1.8 and 0.9 groups per nm(2), respectively. The X-ray diffraction patterns and the narrow pore size distributions obtained from the gas sorption isotherms showed that the modified materials retained the characteristic pore structure of the underlying MCM-48 material. CH(3)-MCM-48 exhibited significantly improved hydrolytic stability over the unmodified MCM-48 under the aqueous conditions tested, whereas NH(2)-MCM-48 appeared to be less stable than the unmodified MCM-48. The decrease in stability is most likely due to the nature of the attachment of the 3-aminopropyldimethylsilane moiety, where the conversion of surface silanol groups is limited by H bonding with the amino end, leading to a 50% lower surface concentration and resulting in an increased likelihood of nucleophilic attack on the silica surface, enhancing the rate of hydrolysis. Hexamethyldisilazane thus appears to be a superior functional group for modifying the MCM-48 surface.     

Tailoring pore properties of MCM-48 silica for selective adsorption of CO2

Four different types of amine-attached MCM-48 silicas were prepared and investigated for CO(2) separation from N(2). Monomeric and polymeric hindered and unhindered amines were attached to the pore surface of the MCM-48 silica and characterized with respect to their CO(2) sorption properties. The pore structures and amino group content in these modified silicas were investigated by XRD, FT-IR, TGA, N(2) adsorption/desorption at 77 K and CHN/Si analysis, which confirmed that in all cases the amino groups were attached to the pore surface of MCM-48 at 1.5-5.2 mmol/g. The N(2) adsorption/desorption analysis showed a considerable decrease of the pore volume and surface area for the MCM-48 silica containing a polymeric amine (e.g., polyethyleneimine). The CO(2) adsorption rates and capacities of the amine-attached MCM-48 samples were studied employing a sorption microbalance. The results obtained indicated that in addition to the concentration of surface-attached amino groups, specific interactions between CO(2) and the surface amino groups, and the resultant pore structure after amine group attachment have a significant impact on CO(2) adsorption properties of these promising adsorbent materials.     

Characterization of methylated nanoscale MCM-41 material

In this study, nanoscale MCM-41 molecular sieve was prepared under a basic condition by a hydrothermal method using cetyltrimethylammonium bromide as a template and tetraethyl orthosilicate as a silica source. Methylated nanoscale MCM-41 molecular sieve was prepared from the nanoscale MCM-41 by post-synthesis method using trimethylchlorosilane (TMCS) as coupling agent. The product was characterized by means of element analysis, powder X-ray diffraction, Fourier transform infrared (FT-IR) spectroscopy, low-temperature nitrogen adsorption-desorption technique at 77 K, scanning electron microscopic (SEM), thermogravimetry-differential thermal analysis (TG-DTA). Powder XRD showed that the framework of the molecular sieve was well retained and the degree of ordering of the methylated MCM-41 decreases. IR spectra and the low-temperature nitrogen adsorption-desorption technique suggested that methyl was successfully grafted to the inner surface of the methylated MCM-41 and the mesoporous channels of the methylated MCM-41 were still maintained. Scanning electron microscopic results showed that the average size of the methylated MCM-41 prepared was 112 nm. Differential thermal analysis showed that the prepared material has preferable thermal stability and the methylated MCM-41 can be stable at 903 °C.     

Characterization and catalytic performance of methyl-grafted Ti-HMS catalysts prepared by the CVD method

Methyl-grafted Ti-HMS catalysts were prepared by the chemical vapor deposition (CVD) method using TiCl₄ as titanium source and various organic silanes as silylating agents. The catalysts were characterized by XRD, N₂-adsorption-desorption, FTIR, ²⁹Si NMR, TGA, DR UV-vis, and evaluated by the epoxidation of propylene using cumene hydroperoxide (CHP) as oxidant. The results reveal that the silylated Ti-HMS catalysts are more active than the unsilylated Ti-HMS catalyst, and the methyl-grafted Ti-HMS catalyst silylated with hexamethyldisilazane (HMDSZ) exhibits better epoxidation performance than the analogues silylated with trimethylchlorosilane (TMCS) or dimethyldichorosilane (DMDCS). It is proposed that not only the form of T-O-SiMe_n (n = 2 or 3) but also the breakage of Ti-O-T (Si-O-Si or Si-O-Ti) are observed in silylation using Cl-containing silylating agents (TMCS or DMDCS), which decrease the hydrophobicity of Ti-HMS catalysts and destroy the tetracoordinated titanium species that responsible for the epoxidation performance. This phenomenon has not been observed in silylation with HMDSZ.     

Gas adsorption in mesoporous micelle-templated silicas: MCM-41, MCM-48, and SBA-15

This paper reports a molecular simulation and experimental study on the adsorption and condensation of simple fluids in mesoporous micelle-templated silicas MCM-41, MCM-48, and SBA-15. MCM-41 is described as a regular cylindrical silica nanopore, while SBA-15 is assumed to be made up of cylindrical nanopores that are connected through lateral channels. The 3D-connected topology of MCM-48 is described using a gyroid periodic minimal surface. Argon adsorption at 77 K is calculated for the three materials using Grand Canonical Monte Carlo simulations. Qualitative comparison with experiments for nitrogen adsorption in mesoporous micelle-templated silicas is made. The adsorption isotherm for SBA-15 resembles that for MCM-41. In particular, capillary condensation and evaporation are not affected by the presence of the connecting lateral channels. In contrast, the argon adsorption isotherm for MCM-48 departs from that for MCM-41 having the same pore size. While condensation in MCM-41 is a one-step process, filling of MCM-48 involves two successive jumps in the adsorbed amounts which correspond to condensation in different domains of the porosity. The condensation pressure for MCM-48 is larger than that for MCM-41. We attribute this result to the morphology of the MCM-48 surface (made up of both concave and convex regions) that differs from that for MCM-41 (concave only). Our results suggest that the pore connectivity affects pore filling when the size of the connections is comparable to that of the nanopores.     

Morphology of nanostructured platinum in mesoporous materials-effect of solvent and intrachannel surface

An intrachannel surface of host silica was functionalized through the reaction of surface silanol groups with silanes to generate a monolayer of positively charged groups, and together with the strongly adsorbed and negatively charged PtCl6(2-), resulting in nanostructured platinum-mesoporous silica composites. The highly dispersed Pt nanoparticles and nanonetworks are fabricated from (CH3O)3Si(CH2)3N(CH3)3+Cl- functionalized mesoporous silica MCM-48 with H2PtCl6 in ethanol and water solvent, and characterized by PXRD, XAS, TEM, and N2 adsorption. The solvent of H2PtCl6 solution is found to affect the mobility of Pt precursors and the resulting morphology of nanostructured metallic Pt. The effect of the intrachannel surface properties on the incorporation and the morphology of nanostructured Pt on the deposition of Pt(NH3)4Cl2 and H2PtCl6 on Al-doped or C-coated mesoporous silica MCM-41 is also studied relative to that on pure silica MCM-41.     

蔗糖在MCM-48表面的自发单层分散

采用液相浸渍法研究了蔗糖在中孔MCM-48表面的自发单层分散. 用X射线衍射(XRD)相定量分析法, 测定了蔗糖在MCM-48上的最大分散容量, 并用差热分析、N2吸附技术对制备的样品进行表征. 结果表明, 在蔗糖与MCM-48的质量比小于1.1时, 蔗糖在MCM-48表面能自发分散成单层. 当蔗糖/MCM-48 质量比为0.8时, MCM-48的比表面积由初始的998 m2·g-1降至114 m2·g-1, 孔径由原来的2.7 nm降至2.0 nm, 孔容由0.76 cm3·g-1降至0.11 cm3·g-1. 当蔗糖与MCM-48的质量比超过1.1时, MCM-48的比表面积迅速减小至10 m2·g-1以下. 这是因为蔗糖分子大小和MCM-48孔径相差不大, 导致蔗糖在MCM-48表面分散时出现孔道堵塞.     

KIT-1介孔分子筛的化学修饰及吸附性能

介孔分子筛MCM-41具有较大、可调的孔径和较高的比表面积，其骨架组成具有较强的可调变性．为该材料的应用提供了很大的空间。但全硅MCM-41分子筛在潮湿空气中，即使在室温条件下也会发生水解反应，使其介孔结构遭到破坏。前人已针对MCM-41分子筛稳定性不足的问题相继合成了稳定性较高的介孔分子筛KIT-1,     

Advanced surface functionalization of periodic mesoporous silica: Kinetic control by trisilazane reagents

The surface reactions of mesoporous silica MCM-41 with a series of new trisilylamines (trisilazanes) (SiHMe2)2NSiMe2R and (SiMe2Vin)2NSiMe2R (R = indenyl, norpinanyl, chloropropyl, 3-(N-morpholin)propyl; Vin = vinyl), disilylalkylamine (SiHMe2)iPrNSiMe2(CH2)3Cl, and monosilyldialkylamines Me2NSiMe2R (R = indenyl, chloropropyl, 3-(N-morpholin)propyl) were investigated. 1H, 13C, and 29Si MAS NMR spectroscopy, nitrogen adsorption/desorption, infrared spectroscopy, and model reactions with calix[4]arene as a mimic for an oxo surface were used to clarify the chemical nature of surface-bonded silyl groups. The trisilylamines exhibited a comparatively slow surface reaction, which allowed for the adjustment of the amount of silylated and nonreacted SiOH groups and led to a stoichiometric distribution of surface functionalities. The 2:1 integral ratio of SiHMe2 and SiMe2R moieties of such trisilazanes was found to be preserved on the silica surface as indicated by microanalytical as well as 13C and 29Si MAS NMR spectroscopic data of the hybrid materials. For example, the reaction of MCM-41 with (SiHMe2)2NSiMe2(CH2)3Cl, (SiHMe2)iPrNSiMe2(CH2)3Cl, and Me2NSiMe2(CH2)3Cl provided bi- and monofunctional hybrid materials with one-third, one-half, or all chemically accessible silanol groups derivatized by chloropropyl groups, respectively. Thus, a molecular precursor strategy was developed to efficiently control the relative amount of three different surface species, SiHMe2 (or SiVinMe2), SiMe2R, and SiOH, in a single reaction step. The reaction behavior of indenyl-substituted monosilazanes and trisilazanes (R = Ind) with calix[4]arene proved that the indenyl substituent can act as a leaving group forming a dimethylsilyl species, which is anchored bipodally on the silica surface, that is, via two Si-O bonds.