高分子催化剂聚氯乙烯—三氯化铁催化合成缩醛（酮）

本文首次将高分子催化剂聚氯乙烯—三氯化铁应用于缩醛和缩酮的合成中,乙二醇或1,2—丙二醇与醛或酮的羰基作用生成缩醛或缩酮。当0.2mol醛或酮与0.3mol醇的混合物在0.5g催化剂作用下,用环已烷为溶剂,回流反应50分钟,其收率为78—91％。     

甲基磺酸催化合成季戊四醇双缩醛(酮)

季戊四醇双缩醛、双缩酮化合物在工业和有机合成中应用广泛。工业上常作为增塑剂、抗氧剂、杀虫剂和表面活性剂的消泡剂,在有机合成中用来合成有生理活性的物质和作为醛、酮的保护基团。季戊四醇双缩醛、酮的合成通常在酸性条件下进行,已报道的催化剂有质子酸:如盐酸[1]、硫酸[     

磷钨酸镧催化合成缩醛(酮)的研究

以磷钨酸镧为催化剂催化合成了苯甲醛乙二醇缩醛、苯甲醛1,2-丙二醇缩醛及环己酮乙二醇缩酮.较系统研究了反应物料配比、催化剂用量、反应时间、催化剂重复使用性能等因素对反应的影响.结果表明:在醛(酮)/二元醇(乙二醇、1,2-丙二醇)=1.0:1.5(mol/mol),催化剂用量为反应物料总质量的1.0%,环己烷为带水剂,在反应温度86～96℃条件下,反应时间2.0h,苯甲醛乙二醇缩醛收率为78.5%,苯甲醛1,2-丙二醇缩醛收率为76.1%,环己酮乙二醇缩酮收率为79.5%.     

钨硅酸的制备及其在催化合成缩酮(醛)中的应用

本文探讨了钨硅酸的制备方法,以合成环己酮1,2-内二醇缩酮为例验证钨硅酸的催化活性,并探讨了合成其它缩酮（醛）的适宜条件,得到的收率分别为：环己酮1,2-丙二醇缩酮85．5％、环己酮乙二醇缩酮89．6％、丁酮乙二醇缩酮79．5％、丁醛乙二醇缩醛89．1％、丁醛1,2丙二醇缩醛81．5％。     

微波辐射条件下季戊四醇双缩醛和双缩酮化合物的合成

微波辐射硫酸锆-硅胶催化季戊四醇与醛、酮缩合反应,高收率制得了双缩醛和双缩酮化合物.该方法操作简便,收率高,催化剂可重复使用,是一种环境友好型催化反应.     

磺化聚苯乙烯大孔树脂催化醛、酮与乙二醇缩合

合成了交换量不同的磺化聚苯乙烯大孔树脂,并将其运用于催化环已酮与乙二醇、苯甲醛与乙二醇的缩合反应。实验表明,磺化聚苯乙烯大孔树脂对醛、酮与乙二醇的缩合反应的催化效果良好,在0.2mol酮(或醛)中加入0.1g树脂,催化环己酮与乙二醇缩合反应的产率最高可达98.2%,催化苯甲醛与乙二醇缩合反应的产率可达73.3%。同时还发现磺化聚苯乙烯大孔树脂的交换量与催化合成缩酮、缩醛的产率有关,交换量为1.00mmol/g时其产率最高,催化性能较稳定。交换量小和交换量太大的树脂催化产率低。该树脂可以重复使用。催化反应完成后,树脂与反应液的分离十分方便,且催化剂对环境没有污染。     

正交试验法优化合成环己酮Vc缩酮

缩醛或缩酮是一类具有广泛用途的高档新型香料[1].近年来,国内不少学者对环己酮缩酮的合成作过一些报道,主要工作是探讨催化剂对环己酮缩酮合成反应的影响,所用的醇大多为乙二醇[2-6].     

含硅二烃基锡化合物对醇醛(酮)缩合反应的催化活性

考察了10种含硅二烃基锡化合物对柠檬醛与乙二醇及环己酮与乙二醇的缩合反应的催化活性。 研究了催化剂用量、反应时间、醛醇及酮醇的物质的量之比和溶剂等对反应产率的影响。 结果表明,除一种催化剂外,9种化合物对缩醛和缩酮反应均有良好的催化活性,当催化剂用量为反应物质量分数的1.4%,醛与乙二醇的物质量之比为1∶1.3,酮与乙二醇的物质量之比为1∶1.6,以环己烷为带水剂,回流反应3 h,产物收率分别达92%和86%以上。     

新固体超强酸的制备和缩酮的合成

报道了新型固体超强酸Fe2O3／S2O8^2-催化剂的制备及其催化合成缩酮的研究工作,探讨了Fe2O3／S2O8^2-的制备方法和合成缩酮的反应条件。结果表明：酮(醛)117mmol,苯为带水剂,催化剂Fe2O3／S2O8^2-用量为原料总质量的8．4％,酮醇摩尔比为1．0：3．0,回流反应时间为4h,缩酮平均产率高达95．5％。     

磷钨酸铜绿色催化合成乙酰缩醛的研究

合成了磷钨酸铜并利用XRD、FT-IR和UV等对其结构进行了表征,结果表明其具有Keggin结构.在室温无溶剂条件下,考察了磷钨酸铜催化一系列醛和乙酸酐合成相应的乙酰缩醛的反应.结果表明,醛和乙酸酐的物质量比为1∶2,磷钨酸铜用量仅需占醛的0.5%(摩尔比)就能使反应在较短时间内完成,产物产率可达62%~96%.该催化剂在醛和酮同时存在时,可以选择性地与醛基发生反应.     

Acetalation and Ketalation Catalyzed by SO42-/TiO2-MoO3

The catalytic activities of SO42-/TiO2-MoO3 in synthesizing cyclohexanone ethylene ketal,cyclohexanone 1,2-propanediol ketal, 2-propyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane,2-isopropyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane, butanone ethy-lene ketal and butanone 1,2-propanediol ketal were reported. It has been demonstrated that SO42-/TiO2-MoO3 is an excellent catalyst. Various factors concerned in this reaction have been investigated. The optimum conditions have been found, that is, the molar ratio of aldehyde/ketone to alcohol was 1:1.5 or 1:1.3,the mass ratio of the catalyst used to the reactants was 0.25～1.5%, and the reaction time was 45～60 min. Under this conditions, the yield of cyclohexanone ethylene ketal is 82.7%, cyclohexanone 1,2-propanediol ketal is 83.4%, the yield of 2-propyl-1,3-dioxolane is 68.1%,4-methyl-2-isopropyl-1,3-dioxolane is 87.5%, the yield of 2-isopropyl-1,3-dioxolane is 70.7%,4-methyl-2-isopropyl-1,3-dioxolane is 82.5%, the yield of butanone ethylene ketal is 74.1%, and butanone 1,2-propanediol ketal is 94.9%.Some equation and experiment results concerned of the synthetic acetals or ketals were listed as follows.     

New rearrangement reactions of the trichothecane framework]

Treatment of the apotrichothecane derivative 4 with H₂SO₄ in dioxan gave the acetal 6 and with H₂SO₄ in acetone the ketal 9 . Whereas the oxidation of 4 with Ag₂CO₃ yielded the hydroxy aldehyde 7 , the reaction with CrO₃ or MnO₂ led to the α,β-unsaturated ketone 8 . Upon treatment of 8 with base the cyclic keto ether 11 was obtained due to 1,4-addition. Acetylation of the latter compound gave a mixture consisting of the enolacetate 13 and the acetylketone 14 . The oxim 15 of ketone 14 was transformed to the nitrile 16 and not the Beckmann fragmentation product 18 . For the identification of the C(11) hydrogen atom in biosynthetic studies the triol 22 was oxidized to the keto aldehyde 26 which, upon treatment with methanolic K₂CO₃, gave the spirolactol 30 and the cyclic acetal 29 as second product when the reaction was carried out in dilute solution. The spirolactol 30 was oxidized to the spirolactone 31 . The corresponding 19 possessing the intact 12,13-epoxy group underwent rearrangement to the apotrichothecane derivatives 20 and 21 under the same conditions. Oxidation of the triol 22 with MnO₂ or CrO₃ gave a mixture of the acetal 23 and the keto acid 24 . – The mechanisms of the rearrangements observed are discussed.     

Enantioselective total synthesis of (+)-leucascandrolide A macrolactone

[reaction: see text] The enantioselective synthesis of the (+)-leucascandrolide A macrolactone has been achieved in 20 linear steps from 1,3-propanediol. The key steps in the synthesis are a reductive cleavage of bicyclic ketal 5 to establish the C15 stereogenic center and a diastereoselective aldol of the boron enolate of methyl ketone 3 to aldehyde 4 in preparation for a heteroconjugate addition for the introduction of the C3 stereocenter.     

Dendritic aliphatic polyethers as high-loading soluble supports for carbonyl compounds and parallel membrane separation techniques

This paper describes the use of dendritic polyglycerol as a new high-loading polymeric support. The soluble polyether skeleton allows the parallel synthesis of small libraries on a large scale (1-5 mmol). Purification of polymer-bound products is easily achieved by a parallel dialysis apparatus, which was developed to separate up to 12 reaction mixtures simultaneously. The terminal 1,2-diol groups of polyglycerol (loading capacity: 4.1 mmol diol/g) can be directly coupled with carbonyl compounds without additional linker groups. At the same time the polyglycerol support acts as a polymeric ketal protecting group. The coupling of the carbonyl compounds occurs in high yields, and effective loading capacities of up to 3.5 mmol of ketone/g can be reached. The obtained polymeric acetals can easily be characterized by standard analytical techniques, such as NMR, IR, UV, and SEC. The versatility of this new polymeric support for solution-phase organic synthesis is demonstrated by two efficient polymer-supported syntheses: nucleophilic substitutions of gamma-chloroketones with amines and Suzuki-coupling on p-bromobenzaldehyde. The acid-catalyzed acetal cleavage with a solid-phase acidic ion-exchange resin in methanol demonstrates the orthogonal use of these soluble polymeric supports with conventional solid-phase reagents. Cleavage of products occurs in high yields, and almost complete recovery (>95%) of the polyglycerol support has been demonstrated after phase separation or ultrafiltration.     

三甲基硅化腈在有机合成中的应用

三甲基硅化腈是一种常用的有机合成试剂. 对近年来三甲基硅化腈在有机合成中的应用进行了简要的总结和概述, 重点介绍了三甲基硅化腈作为强的亲核试剂广泛用于环氮和环氧化合物的开环反应、亚胺和醛酮类化合物的加成、胺与醛或酮参与的多组分反应、偶联反应以及对炔和具有较高活性的碳碳双键的氰化加成等反应.     

The α-halogeno ether function: formation and use in the design of tailor-made polymers

α-Halogeno ether species, in appropriate conditions, can induce the “living” cationic polymerization of vinyl ethers. They can also be used as initiators for the “living” polymerization of styrene derivatives. Therefore, their use as intermediates in the preparation of tailor-made polymers and copolymers offers interesting opportunities in macromolecular synthesis. The main parameters which determine and control their reactivity are reviewed and discussed. The possibility to generate quantitatively these derivatives by various routes and from different organic functions such as aldehyde, ketone, acetal and hydroxyl is examined. Some of these routes have been used to generate the α-halogeno ether function directly at the end of acetal and hydroxy-terminated polymers. The latter have then been used as macroinitiators to prepare new block copolymers. The synthesis of poly(isobutyl vinyl ether-β-ethyl vinyl ether), poly(styrene-β-chloroethyl vinyl ether) and poly(chloroethyl vinyl ether-β-butadiene-β-chloroethyl vinyl ether) by this technique is described.     

Construction of the A/B/C core of mexicanolides via a tandem double-aldol reaction

An efficient and concise approach for rapid assembly of the ABC tricyclic carbon skeleton of mexicanolide-type limonoids is described. The acetal/ketal diketoester precursors were prepared from simple starting materials by LiOH-mediated Michael reactions. The ABC tricyclic skeleton bearing multiple stereogenic centers was efficiently constructed by a powerful one-pot cascade reaction, which includes acetal/ketal hydrolysis, double intramolecular aldol condensation, and alkene migration.     

Lithiated anions derived from (alkenyl)pentamethyl phosphoric triamides: Useful synthons for the stereoselective synthesis of 9-oxo- and 10-hydroxy-2(E)-decenoic acids, important components of queen substance and royal jelly of honeybee Apis mellifera

Lithiated anions derived from (alkenyl)pentamethyl phosphoric triamides as homoenolate equivalents are used in the reaction with halogenated acetal and ketal giving regioselectively the γ-alkylation adducts. Chemoselective acidic hydrolysis of the enephosphoramide moiety in the presence of acetal or ketal groups leads to expected carbonyl products, key intermediates in the synthesis of natural compounds. The synthetic potential of the presented strategy is illustrated by stereoselective synthesis of two pheromones namely, 9-oxo-2(E)-decenoic acid 1 from queen substance and 10-hydroxy-2(E)-decenoic acid 2 from royal jelly of honeybee Apis mellifera.