丙烯酸(丁酯)改性聚乙烯醇水溶性的研究

本文采用半连续乳液聚合方法,通过引入丙烯酸(AA)和丙烯酸丁酯(BA)与醋酸乙烯酯(VAc)共聚合得到改性的聚醋酸乙烯酯,经过破乳,洗涤,干燥,醇解得到改性聚乙烯醇。采用X射线衍射(XRD)、傅立叶红外光谱(FT-IR)、核磁共振(1H-NMR)等手段研究了不同比例的丙烯酸和丙烯酸丁酯对聚乙烯醇结构和溶解性的影响,结果表明,改性聚乙烯醇的溶解性得到明显改善,当AA∶BA=6∶4时,浓度为5%的改性聚乙烯醇水溶液在25℃下静置6.5h就能完全溶解于水中;在磁力搅拌下,25min左右就完全溶解。     

离子液体中脂肪酶催化拆分外消旋烯丙酮醇反应

 以离子液体为溶剂,考察了溶剂类型、水活度、温度、 pH值和共溶剂等因素对脂肪酶催化拆分外消旋烯丙酮醇(R,S)-4-羟基-3-甲基-2-(2-丙烯基)-2-环戊烯-1-酮反应的影响,并与常用于外消旋烯丙酮醇拆分的有机溶剂乙酸乙烯酯进行了比较. 结果表明,在离子液体［bmim］PF6中脂肪酶的催化性能较好,酶初始反应速率为18.48 μmol/(g·min), 半衰期为74.53 h, 高于在乙酸乙烯酯中的相应值(9.18 μmol/(g·min)和64.29 h). 但离子液体中拆分反应的转化率低于在乙酸乙烯酯中的转化率,可以通过向离子液体中补加酰基供体来提高外消旋烯丙酮醇的转化率. 两种反应介质中最佳酶反应条件均为水活度0.17, 温度40 ℃和pH=7, 但加入共溶剂后,离子液体中脂肪酶催化拆分外消旋烯丙酮醇的效率降低,而在乙酸乙烯酯中则有所提高.     

不同醇对聚合物分散液晶光聚合动力学及其电光特性的影响

以丙烯酸-2-乙基己酯(EHA)、二甲基丙烯酸乙二酯(EDMA)/季戊四醇四丙烯酸酯(PETTA)为混合单体、液晶P0616A为液晶相、Irgacure 184为光引发剂,通过UV光引发制备了聚合物分散液晶(PDLCs),研究了不同烷基链长醇,即乙醇(EtOH)、正丁醇(nBA)、正己醇(nHA)、正辛醇(nOA)和正十四醇(nTA)对体系光聚合动力学及其PDLCs液晶相变温度及电光特性的影响.结果表明引入醇分子显著加快了丙烯酸酯/液晶复合体系的光聚合反应速率,提高了单体的最终转化率,其中以正丁醇体系最为明显.随着醇分子烷基链的增长,体系的转化率趋于降低,但依然明显高于不含醇的体系.醇分子的加入降低了PDLCs中液晶相的TNI,且随着醇分子烷基链长的增长,PDLCs液晶相的TNI总体上呈降低的趋势.醇分子的加入增加了PDLCs液晶微区中向列相液晶的含量,而含正丁醇和正十四醇的体系液晶微区中向列相液晶低于其它3个含醇体系.醇分子的加入明显降低了PDLCs的阈值电压和饱和电压以及对比度.结合体系的光聚合速率和单体转化率,正丁醇是改善PDLCs性能的最佳选择.     

淀粉-丙烯酸反相乳液接枝共聚反应的动力学研究

以过硫酸铵(NH4)2S2O8为引发剂,失水山犁醇单月桂酸酯(Span-20)为乳化剂,采用反相乳液聚合技术,制得了淀粉-丙烯酸接枝共聚物,研究了反应温度、引发剂浓度、单体浓度、乳化剂浓度、淀粉用量五种因素对反应速率的影响。根据单体的转化率,用线性回归法计算聚合反应速率;然后用作图法确定反应的动力学关系式,并求出反应起始阶段的表观活化能。结果表明,其动力学关系式为:Rp∝[(NH4)2S2O8]0.51[AA]1.18[St]0.81[Span-20]0.62;聚合反应恒速阶段的活化能,在53~68℃范围内为26.00 kJ.mol-1。     

聚(3-羟基丁酸酯)/聚氧化乙烯共混物非晶区相容性的固体核磁共振研究

用固体高分辨核磁共振碳谱方法研究了不同组成比的聚 (3 羟基丁酸酯 ) 聚氧化乙烯共混物的结晶度、非晶区的相容性和分子运动能力 .结果表明聚 (3 羟基丁酸酯 )的结晶度几乎不随组成比变化 ,而聚氧化乙烯的结晶度则随其在共混物中含量的降低而显著降低 .聚氧化乙烯的加入使得聚 (3 羟基丁酸酯 )非晶区的分子运动能力有所增强 .共混物的非晶区表现出一定的相容性 ,相容程度与共混物的组成比有关     

丙烯酸(4-N,N-二甲氨基肉桂酰氧乙基)酯及其水溶性聚合物的合成及其光化学性质研究

合成了一种新型感光性单体丙烯酸(4 N,N 二甲氨基肉桂酰氧乙基)酯(DMACEA)及其与丙烯酸的共聚物P(DMACEA co AA).用紫外吸收和荧光光谱研究了聚合物溶液的光敏感性,用傅立叶红外光谱研究了聚合物成膜后的光交联性及其过程.结果表明:DMACEA具有较好的光敏性,P(DMACEA co AA)具有较好光交联性,交联膜水溶胀和透光性也较好.     

基于模型化合物反应路径解析淖毛湖褐煤萃取残渣的甲醇醇解机理

以淖毛湖褐煤(NL)超声辅助萃取残渣(ER)作为研究对象,在300℃下采用甲醇对ER进行醇解,并考察添加KOH对醇解过程的影响.通过GC-MS分析MP(未添加KOH)和MPKOH(添加KOH)两种醇解产物的组成信息.选取苯甲酸苄酯(BB)和乙酸苯酯(PA)作为ER的两种模型化合物(MER),醇解后得到产物BBP、BBP...     

反相悬浮聚合法制备球状卡波树脂的研究

以偶氮二异丁脒盐酸盐(V50)作为引发剂,失水山梨醇硬脂酸酯(Span60)和聚二甲基硅氧烷PEG-7磷酸酯为复合分散剂,蔗糖烯丙基醚和三甲基丙基聚氧乙烯(15)醚三丙烯酸酯为复合交联剂,丙烯酸为单体,正已烷为反应介质,采用反相悬浮聚合方法制备了球状卡波树脂.用光学显微镜和扫描电镜分别对聚合反应的成粒过程和产物的形貌进行了研究.结果表明,聚合体系呈现典型的悬浮聚合相态特征,并获得了堆积密度较高(0.65 g/cm3)的球状卡波树脂.聚合反应动力学研究结果表明,该反相悬浮聚合的聚合速率对单体浓度和引发剂浓度的反应级数分别约为1.36和0.70;聚合反应的表观活化能为78.0 kJ/mol.交联剂对卡波树脂的性能有重要的影响,通过适度交联可提高产物的增稠效率及其抗剪切性能.     

超声辐照醋酸乙烯酯的乳液聚合

将超声波引入醋酸乙烯酯(VAc)乳液聚合,实现了醋酸乙烯酯的低温快速聚合。考察了超声功率、乳化剂十二烷基硫酸钠(SDS)和引发剂过硫酸钾(KPS)的浓度对聚合反应的影响。实验结果表明,在VAc 7 mL,H2O 63 mL,w(SDS)1%,c(KPS)4 mmol.L-1,900 W的聚合反应条件下,于25℃反应30 min,VAc的转化率高于80%。     

ATRP法合成聚去氢枞酸丙烯酸乙二醇酯的研究

本研究从歧化松香中提取的去氢枞酸(DHA)出发,经酰氯化后与丙烯酸(2-羟基)乙酯反应,合成了去氢枞酸丙烯酸乙二醇酯(DHAAGE);并以此为单体,2-溴-异丁酸乙酯(EBr-iB)为引发剂,CuBr/2,2'-联吡啶(2,2'-bipyridine)为催化体系,在90 oC下,利用原子转移聚合(ATRP)法制备了聚去氢枞酸丙烯酸乙二醇酯(PDHAAGE).利用FT-IR、1H-NMR和GPC对所制备的单体和聚合物进行了表征,同时考察了单体转化率随聚合反应时间的变化.结果表明,聚合反应动力学曲线呈良好线性关系,表观聚合速率常数kp′为3.6 ×10-7 s-1;所得聚合物的分子量分布很窄.     

Preparation of Syndiotacticity-Rich High Molecular Weight Polyvinyl Alcohol by Low Temperature Emulsifier-Free Emulsion Copolymerization of Vinyl Acetate and Vinyl Pivalate

Low temperature emulsifier-free emulsion copolymerization of vinyl acetate (VAc) and vinyl pivalate (VPi) was carried out using a redox initiation system to prepare syndiotacticity-rich high-molecular weight (HMW) polyvinyl alcohol (PVA) with high yield. The effects of the polymerization conditions on the conversion, the molecular weight, the structure of poly (vinyl acetate-co-vinyl pivalate) (P (VAc-VPi)) and syndiotacticity of PVA were investigated. With the increases of the initiator concentration, the VPi molar ratio in monomer and polymerization temperature, the degree of polymerization (DP) of PVA decreases distinctly, but VPi contents in copolymer and syndiotactic diad (S-diad) contents of PVA increase obviously. PVA with the maximum DP of 11030 can be prepared by complete saponification of P(VAc-VPi) obtained under condition that the molar ratio of KPS to monomer is 1/2000, the molar ratio of VAc to VPi is 7:3 and reaction temperature is 12°C. The highest S-diad content in PVA can be up to 59.31% while the DP of PVA decreases to 5180 under the condition that the feed ratio of VPi is 70 mol%, which means the syndiotacticity-rich HMW PVA can be prepared successfully. And the conversions of all reactions are above 80%. Syndiotacticity-rich HMW PVA is effectively prepared in this study, which is useful for the preparation of high-strength and high-modulus PVA fiber.     

超大孔P(AA-co-AM)/PVA水凝胶的制备及吸附性能研究

采用泡沫分散聚合法,以饱和Na2CO3水溶液为发泡剂,过硫酸铵(APS)及NaHSO3为引发剂,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,聚(氧化乙烯/氧化丙烯)(PF127)为泡沫稳定剂,丙烯酸(AA)和丙烯酰胺(AM)为单体,聚乙烯醇(PVA)为第二网络,制备超大孔半互穿水凝胶P(AA-co-AM)/PVA,并研究其对阳离子兰染料的吸附性能。研究表明,P(AA-co-AM)/PVA具有相互贯穿的超大孔结构;当n(AM):n(AA)=1.5:1,w(PVA)=1.6%时凝胶的平衡溶胀度达186.56g/g;凝胶具有很好的离子响应性,在蒸馏水中的平衡溶胀度为129.16g/g时,在0.1mol/L NaCl溶液中只有31.07g/g;对阳离子兰染料溶液的脱色率达92.17%,吸附容量达17.16mg/g。     

双极膜技术在电氧化制备3-甲基-2-吡啶甲酰胺中的应用

分别以戊二醛和Fe3+改性壳聚糖和海藻酸钠并分别与柔性链聚乙烯醇(PVA)共混, 制备了Fe-SA-CS-GA/PVA聚合物双极膜. 测定膜的红外光谱, I-V工作曲线, Na+与Cl-透过双极膜的迁移数, 离子交换容量及阴阳两极室中OH-及H+的变化, 并以扫描电镜观察膜表面和界面层形态. IR与接触角分析结果表明, CS经GA/PVA改性后其亲水性能得到显著提高. 将SA-CS/PVA双极膜及Nafion膜应用于电氧化制备3-甲基-2-吡啶甲酰胺. 实验结果表明, 以SA-CS/PVA双极膜为隔膜合成3-甲基-2-吡啶甲酰胺的产率达到49.8%, 高于以Nafion膜为隔膜的产率.与传统的的方法相比, 该方法的反应条件温和且能有效利用能源.     

Swelling and Reswelling Characteristics of Cross-Linked Poly(vinyl alcohol)/Chitosan Hydrogel Film

Poly(vinyl alcohol) (PVA), hydrogel was prepared by using glutaraldehyde as a cross-linking agent. The blend semi-synthetic hydrogel film, consisting of PVA and chitosan, was prepared from a solvent-casting technique and characterized for their intermolecular interactions using infrared method. The swelling and reswelling behaviors, as well as mechanical properties of the synthetic and semi-synthetic gels were examined by weighing and tensile testing, respectively. Cross-linking the two types of polymer with glutaraldehyde produces a film with lower crystallinity and smaller swelling and reswelling degrees, but having improved mechanical properties. Also, the two types of films show a pH-dependent swelling characteristic. It was found that, the reswelling properties of synthetic hydrogels can be improved by blending PVA with certain ratio of natural polymer. This blending film, can be improve sandy soil properties for cultivation, such as, controlled release of water.     

PVP/PVA半互穿网络材料的制备及其性能研究

以N-乙烯基吡咯烷酮(NVP)为单体、N,N-亚甲基双丙烯酰胺(BIS)为交联剂、过硫酸铵(APS)为引发剂,在聚乙烯醇(PVA)水溶液中原位聚合制备了半互穿网络结构(semi-IPN)的复合聚合物,并用红外光谱、表面接触角、吸水率以及拉力测试对材料的结构和性能进行了表征。结果表明：所制备的材料具有温敏特性,当交联剂用量达到一定值时,semi-IPN膜的伸长率和弹性模量都存在一个最大值;增加PVA的用量,semi-IPN膜的表面接触角减小,伸长率和弹性模量则增加明显。     

The synthesis of translucent polymer nanolatexes via microemulsion polymerization

Surface-enhanced Raman scattering (SERS)-active substrates of polyvinyl alcohol/gold-silver (PVA/Au-Ag) nanofibers were prepared using a simple approach involving electrospinning. The tunable surface plasmon resonance (SPR) of gold-silver alloy (Au-Ag alloy) nanoparticles (NPs) was achieved by controlling the feed ratio between gold and silver precursors. A higher concentration of Au-Ag alloy NPs could be obtained than the conventional methods, using 1wt% of PVA as the stabilizer. The Au-Ag alloy structure was demonstrated by HRTEM and STEM-EDX. After the electrospinning, the Au-Ag alloy NPs were successfully embedded in PVA nanofibers, as shown in the SEM and TEM images. Raman spectra displayed an apparent enhancement in the signal of 4-mercaptobenzoic acid (4-MBA), pyridine, and thiophenol molecules pre-absorbed from their ethanol solution onto the PVA/Au-Ag nanofibers. Different SERS effects were achieved by varying the Au content or excitation wavelength.     

Fabrication and characterization of microstructured and pH sensitive interpenetrating networks hydrogel films and application in drug delivery field

Novel microstructured and pH sensitive poly(acryliac acid-co-2-hydroxyethyl methacrylate)/poly(vinyl alcohol) (P(AA-co-HEMA)/PVA) interpenetrating network (IPN) hydrogel films were prepared by radical precipitation copolymerization and sequential IPN technology. The first P(AA-co-HEMA) network was synthesized in the present of PVA aqueous solution by radical initiating, then followed by condensation reaction (Glutaraldehyde as crosslinking agent) within the resultant latex, it formed multiple IPN microstructured hydrogel film. The film samples were characterized by IR, SEM and DSC. Swelling and deswelling behaviors and mechanical property showed the novel multiple IPN nanostuctured film had rapid response and good mechanical property. The IPN films were studied as controlled drug delivery material in different pH buffer solution using cationic compound, crystal violet as a model drug. The drug release followed different release mechanism at pH 4.0 and pH 7.4, respectively.     

表面活性剂对制备MoS2纳米微粉的影响

Mo0_2纳米微粉在催化l‘l、敏感元件［‘·’］及磁记录材料［‘］等方面具有特殊用途,其传统制备方法是通过在高温下用氢还原l’,‘l,利用这种方法制备M。0。纳米微粉、所得产品粒子尺寸较大,比表面积小,且反应在条件苛刻,从而限制了M00。纳米微粉的使用范围．文献曾报导用y一辐照法制备了一系列金属、合金和氧化物的纳米粒子”－‘Q’,这种方法利用水辐解产生的水合电子（efo）作为还原剂,具有在常温常压下进行操作的显著优点,因而受到普遍关注．本实验室l‘’1曾报导通过v一辐照法可制备Moo。纳米非晶,其颗粒尺寸为8－30urn…     

Thermosensitive poly(methyl methacrylate) emulsion prepared in the presence of poly(vinyl alcohol) with a cloud point as a protective colloid

An emulsion of poly(methyl methacrylate) (PMMA) was prepared using poly(vinyl alcohol) (PVA) of low degree of hydrolysis with a cloud point as a protective colloid. The behaviour of an aqueous solution of PVA with 80% degree of hydrolysis was first investigated in terms of the Huggins constant in viscometry. MMA was polymerized using the PVA at 20 °C, where no abnormality in the aqueous PVA was observed. The change in transmittance of the emulsion observed with a UV–vis photometer revealed that in the case of UV light of wavelength 370 nm, the transmittance decreased markedly at around 30 °C with an increase in temperature, and then increased with a decrease in temperature. The thermosensitive property resulted from PVA with a low degree of hydrolysis with a cloud point, at a higher temperature of which the PVA loses solubility in water owing to weakening of the hydrogen bond between PVA molecules and water.