Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

Ni/Au Schottky gate oxidation and BCB passivation for high-breakdown-voltage AlGaN/GaN HEMT

A new AlGaN/GaN high electron mobility transistor (HEMT) employing Ni/Au Schottky gate oxidation and benzocyclobutene (BCB) passivation is fabricated in order to increase a breakdown voltage and forward drain current. The Ni/Au Schottky gate metal with a thickness of 50/300 nm is oxidized under oxygen ambient at 500 C and the highly resistive NiO is formed at the gate edge. The leakage current of AlGaN/GaN HEMTs is decreased from 4.94 μA to 3.34 nA due to the formation of NiO. The BCB, which has a low dielectric constant, successfully passivates AlGaN/GaN HEMTs by suppressing electron injection into surface states. The BCB passivation layer has a low capacitance, so BCB passivation increases the switching speed of AlGaN/GaN HEMTs compared with silicon nitride passivation, which has a high dielectric constant. The forward drain current of a BCB-passivated device is 199 mA /mm, while that of an unpassivated device is 172 mA /mm due to the increase in two-dimensional electron gas (2DEG) charge.     

Fluorine-plasma treated AlGaN/GaN high electronic mobility transistors under off-state overdrive stress

Influences of off-state overdrive stress on the fluorine-plasma treated AlGaN/GaN high-electronic mobility transistors (HEMTs) are experimentally investigated. It is observed that the reverse leakage current between the gate and source decreases after the off-state stress, whereas the current between the gate and drain increases. By analyzing those changes of the reverse currents based on the Frenkel-Poole model, we realize that the ionization of fluorine ions occurs during the off-state stress. Furthermore, threshold voltage degradation is also observed after the off-state stress, but the degradations of AlGaN/GaN HEMTs treated with different F-plasma RF powers are different. By comparing the differences between those devices, we find that the F-ions incorporated in the GaN buffer layer play an important role in averting degradation. Lastly, suggestions to obtain a more stable fluorine-plasma treated AlGaN/GaN HEMT are put forwarded.     

Simulation design of normally-off AlGaN/GaN high-electron-mobility transistors with p-GaN Schottky hybrid gate

A novel normally-off AlGaN/GaN high-electron-mobility transistor (HEMT) with a p-GaN Schottky hybrid gate (PSHG) is proposed, and compared with the conventional p-GaN normally-off AlGaN/GaN HEMTs. This structure can be realized by selective etching of p-GaN layer, which enables the Schottky junction and PN junction to control the channel charge at the same time. The direct current (DC) and switching characteristics of the PSHG HEMTs are simulated by Slivaco TCAD, and the p-GaN HEMTs and conventional normally-on HEMTs are also simulated for comparison. The simulation results show that the PSHG HEMTs have a higher current density and a lower on-resistance than p-GaN HEMTs, which is more obvious with the decrease of p-GaN ratios of the PSHG HEMTs. The breakdown voltage and threshold voltage of the PSHG HEMTs are very close to those of the p-GaN HEMTs. In addition, the PSHG HEMTs have a higher switching speed than the conventional normally-on HEMTs, and the p-GaN layer ratio has no obvious effect on the switching speed.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.     

Short-gate AlGaN/GaN high-electron mobility transistors with BGaN buffer

Using the semi-insulating property and small lattice constant a of wurtzite BGaN alloy, we propose a BGaN buffer with a B-content of 1% to enhance two-dimensional electron gas(2 DEG) confinement in a short-gate AlGaN/GaN highelectron mobility transistor(HEMT). Based on the two-dimensional TCAD simulation, the direct current(DC) and radio frequency(RF) characteristics of the AlGaN/GaN/B_(0.01)Ga_(0.99)N structure HEMTs are theoretically studied. Our results show that the BGaN buffer device achieves good pinch-off quality and improves RF performance compared with GaN buffer device. The BGaN buffer device can allow a good immunity to shift of threshold voltage for the aspect ratio(LG/d)down to 6, which is much lower than that the GaN buffer device with L_G/d=11 can reach. Furthermore, due to a similar manner of enhancing 2 DEG confinement, the B_(0.01)Ga_(0.99)N buffer device has similar DC and RF characteristics to those the AlGaN buffer device possesses, and its ability to control short-channel effects(SCEs) is comparable to that of an Al_(0.03)Ga_(0.97)N buffer. Therefore, this BGaN buffer with very small B-content promises to be a new method to suppress SCEs in GaN HEMTs.     

Evaluation of thermal resistance constitution for packaged AlGaN/GaN high electron mobility transistors by structure function method

The evaluation of thermal resistance constitution for packaged AlGaN/GaN high electron mobility transistor (HEMT) by structure function method is proposed in this paper.The evaluation is based on the transient heating measurement of the AlGaN/GaN HEMT by pulsed electrical temperature sensitive parameter method.The extracted chip-level and package-level thermal resistances of the packaged multi-finger AlGaN/GaN HEMT with 400-μm SiC substrate are 22.5 K/W and 7.2 K/W respectively,which provides a non-invasive method to evaluate the chip-level thermal resistance of packaged AlGaN/GaN HEMTs.It is also experimentally proved that the extraction of the chiplevel thermal resistance by this proposed method is not influenced by package form of the tested device and temperature boundary condition of measurement stage.     

Impact of oxygen in electrical properties and hot-carrier stress-induced degradation of GaN high electron mobility transistors

The role of the oxygen in AlGaN/GaN high electron mobility transistors (HEMTs) before and after semi-on state stress was discussed. Comparing with the electrical characteristics of the devices in vacuum, air, and oxygen atmosphere, it is revealed that the oxygen has significant influence on the electric characteristics and the hot-carrier-stress-induced degradation of the device. Comparing with the situation in vacuum, the gate leakage increased an order of magnitude in oxygen and air atmosphere. Double gate structure was used to separate the barrier leakage and surface leakage of AlGaN/GaN HEMT it is found that surface leakage is the major influencing factor in gate leakage of SiN-passivated devices before and after semi-on state stress. During semi-on state stress in the oxygen atmosphere, the electric-field-driven oxidation process promoted the oxidation of the nitride layer, and the oxidation layer in the SiN/AlGaN interface leads to the decreasing of the surface leakage.     

Novel model of a AlGaN/GaN high electron mobility transistor based on an artificial neural network

In this paper we present a novel approach to modeling AlGaN/GaN high electron mobility transistor(HEMT) with an artificial neural network(ANN).The AlGaN/GaN HEMT device structure and its fabrication process are described.The circuit-based Neuro-space mapping(neuro-SM) technique is studied in detail.The EEHEMT model is implemented according to the measurement results of the designed device,which serves as a coarse model.An ANN is proposed to model AlGaN/GaN HEMT based on the coarse model.Its optimization is performed.The simulation results from the model are compared with the measurement results.It is shown that the simulation results obtained from the ANN model of AlGaN/GaN HEMT are more accurate than those obtained from the EEHEMT model.     

增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

The physical process analysis of the capacitance-voltage characteristics of AlGaN/AlN/GaN high electron mobility transistors

This paper deduces the expression of the Schottky contact capacitance of AlGaN/AlN/GaN high electron mobility transistors (HEMTs), which will help to understand the electron depleting process. Some material parameters related with capacitance-voltage profiling are given in the expression. Detailed analysis of the forward-biased capacitance has been carried on. The gate capacitance of undoped AlGaN/AlN/GaN HEMT will fall under forward bias. If a rising profile is obviously observed, the donor-like impurity or trap is possibly introduced in the barrier.     

基于GaN同质衬底的高迁移率AlGaN/GaNHEMT材料

研究了表面预处理对GaN同质外延的影响,获得了高电子迁移率AlGaN/GaN异质结材料.通过NH_3/H_2混合气体与H_2交替通入反应室的方法对GaN模板和GaN半绝缘衬底进行高温预处理.研究结果表明,NH_3/H_2能够抑制GaN的分解,避免粗糙表面,但不利于去除表面的杂质,黄光带峰相对强度较高;H_2促进GaN分解,随时间延长GaN分解加剧,导致模板表面粗糙不平,AlGaN/GaN HEMT材料二维电子气迁移率降低.采用NH_3/H_2混合气体与H_2交替气氛模式处理模板或衬底表面,能够清洁表面,去除表面杂质,获得平滑的生长表面和外延材料表面,有利于提高AlGaN/GaN HEMT材料电学性能.在GaN衬底上外延AlGaN/GaN HEMT材料,2DEG迁移率达到2113 cm~2/V·s,电学性能良好.     

Theoretical analytic model for RESURF AlGaN/GaN HEMTs

In this paper, we propose a two-dimensional(2D) analytic model for the channel potential and electric field distribution of the RESURF AlGaN/GaN high electron mobility transistors(HEMTs). The model is constructed by two-dimensional Poisson's equation with appropriate boundary conditions. In the RESURF AlGaN/GaN HEMTs, we utilize the RESURF effect generated by doped negative charge in the AlGaN layer and introduce new electric field peaks in the device channels,thus, homogenizing the distribution of electric field in channel and improving the breakdown voltage of the device. In order to reveal the influence of doped negative charge on the electric field distribution, we demonstrate in detail the influences of the charge doping density and doping position on the potential and electric field distribution of the RESURF AlGaN/GaN HEMTs with double low density drain(LDD). The validity of the model is verified by comparing the results obtained from the analytical model with the simulation results from the ISE software. This analysis method gives a physical insight into the mechanism of the AlGaN/GaN HEMTs and provides reference to modeling other AlGaN/GaN HEMTs device.     

Neutron irradiation effects on A1GaN//GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors(HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10 15 cm 2.The dc characteristics of the devices,such as the drain saturation current and the maximum transconductance,decreased after neutron irradiation.The gate leakage currents increased obviously after neutron irradiation.However,the rf characteristics,such as the cut-off frequency and the maximum frequency,were hardly affected by neutron irradiation.The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism.It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas(2DEG) decreased after neutron irradiation.There was no evidence of the full-width at half-maximum of X-ray diffraction(XRD) rocking curve changing after irradiation,so the dislocation was not influenced by neutron irradiation.It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

Channel temperature determination of multifinger AlGaN/GaN high electron mobility transistor using micro-Raman technique

Self-heating in multifinger AlGaN/GaN high electron mobility transistor (HEMT) is investigated by micro-Raman spectroscopy. The device temperature is probed on the die as a function of applied bias. The operating temperature of AlGaN/GaN HEMT is estimated from the calibration curve of passively heated AlGaN/GaN structure. A linear increase of junction temperature is observed when direct current dissipated power is increased. When the power dissipation is 12.75 W at a drain voltage of 15 V, a peak temperature of 69.1 ℃ is observed at the gate edge on the drain side of the central finger. The position of the highest temperature corresponds to the high-field region at the gate edge.     

基于原位等离子体氮化及低压化学气相沉积-Si_3N_4栅介质的高性能AlGaN/GaN MIS-HEMTs器件的研究

通过对低压化学气相沉积(LPCVD)系统进行改造,实现在沉积Si_3N_4薄膜前的原位等离子体氮化处理,氮等离子体可以有效地降低器件界面处的氧含量和悬挂键,从而获得了较低的LPCVD-Si_3N_4/GaN界面态,通过这种技术制作的MIS-HEMTs器件,在扫描栅压范围V_(G-sweep)=(-30 V,+24 V)时,阈值回滞为186 mV,据我们所知为目前高扫描栅压V_(G+)(20 V)下的最好结果.动态测试表明,在400 V关态应力下,器件的导通电阻仅仅上升1.36倍(关态到开态的时间间隔为100μs).     

An improved EEHEMT model for kink effect on AlGaN/GaN HEMT

In this paper, a new current expression based on both the direct currect(DC) characteristics of the AlGaN/GaN high election mobility transistor(HEMT) and the hyperbolic tangent function tanh is proposed, by which we can describe the kink effect of the AlGaN/GaN HEMT well. Then, an improved EEHEMT model including the proposed current expression is presented. The simulated and measured results of I–V, S-parameter, and radio frequency(RF) large-signal characteristics are compared for a self-developed on-wafer AlGaN/GaN HEMT with ten gate fingers each being 0.4-μm long and 125-μm wide(Such an AlGaN/GaN HEMT is denoted as AlGaN/GaN HEMT(10 × 125 μm)). The improved large signal model simulates the I–V characteristic much more accurately than the original one, and its transconductance and RF characteristics are also in excellent agreement with the measured data.     

DLTS characterization of silicon nitride passivated AlGaN/GaN heterostructures

Passivating the ungated surface of AlGaN/GaN HEMTs with silicon nitride (SiN) is effective in improving the microwave output power performances of these devices. However, very little information is available about surface states in GaN-based HEMTs after SiN passivation. In this work we investigate AlGaN/GaN HEMTs structures having either metal–semiconductor or metal–SiN–semiconductor gate contacts. In short gate devices conductance DLTS measurements point out a hole-like peak that shows an anomalous behaviour and can be ascribed to surface states in the access regions of the device. In insulated gate HEMTs a band of levels is detected and ascribed to surface states, whose energy ranges from 0.14 to 0.43 eV. Capacitance–voltage measurements allow us to point out the existence of a second band of interface states deeper in energy than the former one. This band is responsible for slow transients observed in the characteristics of the insulated gate FAT-HEMT.