4pi聚焦系统中振幅和相位调制的径向偏振涡旋光束聚焦特性的研究

基于Richards-Wolf矢量衍射积分公式, 研究了径向偏振涡旋光束在振幅和相位调制下的4pi聚焦特性.振幅调制是通过振幅滤波实现, 即改变入射光束起始积分值达到调节,相位调制是通过添加相位延迟角δ 的液晶相位延迟器来改变入射光束的偏振态.模拟结果显示,随着振幅的减小, 4pi聚焦系统焦点附近的光轴上呈现出多光球结构; 而相位调制对焦点附近的光强分布产生拉伸作用, 即调节入射光束的拓扑核m和相位延迟器的延迟角δ,可以得到特殊的光强分布. 随着相位δ增大, m=0产生的多光球结构慢慢向光链结构转变,最终变成暗通道;而m=1产生的光链结构慢慢变成光球结构; m=2产生的暗通道变成光球和光链叠加的结构, 这种特殊聚焦光束在光学微操纵领域具有潜在的应用价值. 关键词： 物理光学 偏振 光链 4pi聚焦系统     

90°全息记录衍射效率分析与提高

对光折变全息记录特别是双中心全息记录中90°记录结构下较低的衍射效率进行了研究,采用局域衍射理论对90°记录结构的衍射进行了分析,表明在同样的折射率变化和2 mm的光束宽度的情况下,只有当折射率光栅振幅大于10^-4时,90°记录结构衍射效率才能够与小角度透射记录结构的衍射效率大致相当。针对环境干扰导致的干涉条纹振动影响光栅记录,提出了有效调制度概念,根据分析90°记录结构的干涉条纹间距很小,容易受外界环境干扰而导致低的折射率变化率,因此应采用主动条纹锁定系统。此外在双中心全息记录中,微观光学参量的优化对衍射效率影响也很重要。     

用体全息术对皮秒光脉冲进行二维测量

本文提供一种测量两束相干的ps光脉冲的空间二维时间振幅相关函数的新方法.在此方法中,光脉冲是被记录在一种光致折变的体积全息介质中,而所记录的信息可以通过直接量度在介质中所形成的光栅的空间分布而读出.这种方法可的可行性已为实验证实,它是通过3.5ps倍频锁模Nd:YAG激光测量光致折变晶体LiNbO₃来实现的。     

大角带宽高衍射效率体全息光栅的设计和制备

高性能体全息光栅是全息波导的重要耦合元件,角带宽小、平均衍射效率不高是制约体全息光栅性能的重要因素.以不对称倾斜记录为出发点,设计并制备了大角带宽高衍射效率的体全息光栅.首先讨论在横电模式光和横磁模式光下体全息光栅的记录参数与其衍射效率的关系,找到平均衍射效率较高的记录参数范围,随后进一步分析在此范围内的记录参数与体全...     

Observation of Ramsey fringes in nonlinear Faraday rotation

The evolution of Δm = 2 ground state coherences was investigated in a thermal Rb atomic beam using spatially separated laser beams. The coherence was created by optical pumping with a linearly polarized light beam and was probed, after evolving in a homogeneous magnetic field via the rotation of the plane of polarization of a second light beam. The observed signal shows dispersively shaped Ramsey fringes with a fringe width of 6 kHz.     

Holographic imaging of side-scattering particles

An off-axis holographic system in the side-scattering mode has been studied, and the requirements of fringe resolution and film sensitivity associated with holographic imaging of side-scattering particles analysed. By assuming the Mie scattering model, the fringe distribution about the y-axis (perpendicular to the plane of incidence of the reference light) was found to be asymmetrical, with unevenly distributed spacing, that is narrower in one x direction but greater in the side that is close to the origin. It was demonstrated that commercially available holographic film was sufficient to resolve the fringe frequency over the entire area of the holographic plate, at 60 ° for z = 120 mm, and that images of particles as small as 20 μm could be recorded. Astigmatism was found to occur and be responsible for the distortions of the particle images.     

Volume polarization holographic recording in thick phenanthrenequinone-doped poly(methyl methacrylate) photopolymer

Volume polarization holographic recording in phenanthrenequinone-doped poly (methyl methacrylate) photopolymer is obtained. Photoinduced birefringence in a 2 mm thick sample is measured by a phase-modulated ellipsometry. The birefringence induced in this material by linearly polarized beam at 514 nm reaches 1.2×10(-5). In addition, ability for recording volume polarization grating using two different polarization configurations is demonstrated and compared. The experimental results show that the diffraction efficiency of the hologram reaches to ～40% by using two orthogonal circularly polarized beams.     

Correlation integral as a tool for distinguishing between dynamics and statistics in time series data

We propose a new test for time series data for proper choice of processing technique: dynamical or statistical. It is based upon the normalized slope of the correlation integral (, m) = m⁻¹d(ln C()) /d ln , where m is the embedding dimension. It is shown that when does not tend to 0 on the resolved range of scales as m grows, then there will be serious limitations for dynamical methods even if the data are dynamical by nature. In the latter case it means that the length of time series does not allow to resolve small scales, and on large scales the delay reconstruction for any m mixes true and false neighbours of points and therefore restricts the application of dynamical techniques, such as estimating Lyapunov exponents or predicting time series.     

基于离散衍射光的全息光栅的带宽压缩

提出一种基于离散衍射光的全息光栅的带宽压缩算法。人眼的视觉分辨率是有限的 ,即空间频率变化在Δfpupil以内时 (两根光线的夹角小于 0 .3°) ,不会察觉光线的跳变。首先对衍射光的频谱进行采样 ,使全息光栅衍射的是空间频率不连续的离散光 ,即在光栅的编码中只包含离散光频谱 ,且满足人眼视觉要求。这样 ,光栅的条纹函数为周期性函数 ,因此 ,在条纹编码中我们只需记录一个周期的函数值 (样本数 ) ,光栅的条纹函数的样本数可得到有效的压缩。然后在解码中通过简单的复制可恢复光栅条纹函数的全部样本值。采用这种方法 ,大大压缩了数据量 ,提高了传输速率 ,达到了动态显示的要求     

一种制作投影灰度正弦光栅的新方法

针对传统方法难以制作结构光三维投影测量设备的灰度正弦光栅元件,并以Ronchi光栅代替从而影响测量准确度,提出了一种制作灰度按正弦分布的光栅模板的新方法.通过对银盐全息干板透过率特性曲线的理论分析,指出在对比度为一的正弦干涉条纹下曝光不能得到线性记录和变换的原因,并提出了采用均匀非相干光预曝光提供偏置点来实现线性记录的新方法.实验表明,采用空间滤波法能够获得对称双光束正弦干涉条纹记录,并准确控制正弦干涉条纹曝光在干板的线性区域,可以达到线性记录并获得尽可能高的反衬度.     

Formation of positive and negative anisotropic holographic gratings depending on recording energy in photoreactive liquid crystalline copolymer films

Anisotropic diffractive gratings formed by birefringent molecular alignment are fabricated by a holographic technique using a photo-cross-linkable liquid crystalline copolymer (PLCCP). Depending on the exposure energy used for holographic recording, bright or dark regions of the interference fringe can be chosen for the molecular-aligned region, analogous to positive- and negative-type photoresist processing in photolithography. In conjunction with simultaneously generated surface relief gratings, the anisotropic refractive index modulation inherent in the PLCCP film exhibits different diffraction properties depending on the incident beam polarization. The anisotropic refractive index grating profiles are quantitatively presented for two cases determined by the exposure energy, based on the Fourier analysis of diffractive optics. The selection of different grating formations selected by varying only the exposure energy could provide a strategy for the fabrication of functionalized diffractive optical elements.     

脉冲压缩光栅光路调节新方法研究

介绍了一种简单而实用的大口径脉冲压缩光栅光路调节方法,有效解决了普通光路调节方法中轴向调节精度不高的问题。首先由全息透镜(光栅)成像公式出发,推导出了该光路调节的基本原理。并从光栅记录系统与光栅衍射波像差的关系,结合初级像差理论推导得出叠栅条纹像差为0.4786λ,大约是光栅衍射波像差(0.25λ)的两倍,利用此关系也可对光栅衍射波像差进行实时监测。从数值模拟结果可知,利用叠栅条纹法调节光路可将光栅波像差减至0.06λ,相应的轴向误差量为0.007 mm,可有效提高了轴向调节精度。     

Dual-polarization fiber grating laser-based laser Doppler velocimeter

A dual-frequency laser Doppler velocimeter implemented by a dual-polarization fiber grating laser is proposed,with the two laser frequencies produced by the two orthogonally polarized laser outputs of the fiber grating laser.The reflected laser outputs from a moving target experience the Doppler frequency shift,which is shown to be linearly related to the velocity and the beat note frequency difference between the laser outputs and the reflected light. With a digital frequency demodulation scheme,a high sensitivity of 0.64 MHz/(m/s) and a velocity resolution of less than 0.5% of the velocity for velocity measurement are demonstrated,which shows that the proposed laser Doppler velocimeter is capable of measurement of wide range of velocity.     

Recording receptance of flat plates by holographic interferometry

In the study of mechanical vibrations of structures, the complex ratio of the displacement of the structure at a point divided by the force input to the structure at the same point or a different point is called receptance. This ratio is usually recorded in magnitude and phase by using piezoelectric transducers attached to the structure. This paper describes a study of the feasibility of recording the displacement of a square cantilevered plate not just at one point but over the entire plate surface, by using holographic interferometry. For purposes of comparison of the two techniques a piezoelectric transducer was attached to a free corner of the plate and the displacements at that point were recorded over the frequency range of interest. Although the dynamic range of the holographic technique was found to be somewhat limited, it was found that it is quite feasible to calculate at least the magnitude of the receptance by recording displacements holographically. Since the holographic fringe formation is an integrated effect in time, it was not possible to record the phase by holographic means. The displacements recorded at the corner of the plate by the two methods agreed very well.     

Holographic particle image velocimetry: analysis using a conjugate reconstruction geometry

Holographic recording techniques have recently been studied as a means to extend two-component, planar particle image velocimetry (PIV) techniques for three-component, whole-field velocity measurements. In a similar manner to two-component PIV, three-component, holographic PIV (HPIV) uses correlation-based techniques to extract particle displacement fields from double-exposure holograms. Since a holographic image contains information concerning both the phase and the amplitude of the scattered field it is possible to correlate either the intensity or the complex amplitude. In previous work we have shown that optical methods to compute the autocorrelation of the complex amplitude are inherently more tolerant to aberrations introduced in the reconstruction process, Coupland, Halliwell, Proc. Roy. Soc. 453 (1960) (1997) 1066. In this paper we introduce a new method of holographic recording and reconstruction that allows a constant image shift to be introduced to the particle image displacement. The technique, which we call conjugate reconstruction, resolves directional ambiguity and extends the dynamic range of HPIV. The theory of this method is examined in detail and a relationship between the image and object displacement is derived. Experimental verification of the theory is presented.     

多重分形降趋波动分析法和移动平均法的分形谱算法对比分析

多重分形降趋波动分析法(MFDFA)和多重分形降趋移动平均法(MFDMA)是用来估算一维随机分形信号多重分形谱的两种算法, 已被拓展应用于二维和高维分形信号的分析. 本文简要介绍了MFDFA和MFDMA算法及其在一维时间序列中的应用. 首次系统地从算法模型、计算统计精度、样本量的敏感性、无标度区选取的敏感性、矩选择的敏感性和计算量这六个方面对两种算法进行了对比分析, 以典型多重分形信号BMC信号为例, 分析两种算法的适用性和优劣性. 为实际应用中, 针对具体信号如何选用MFDFA或MFDMA算法, 以及两种算法的参数设置提供了有价值的参考.     

Tilted and axis-shift Lloyd's mirror system for recording low-density and large-area holographic grating

It is difficult to record holographic gratings of low density (<100 lines/mm) and large area simultaneously using traditional holographic system. In order to produce both low-density and large-area holographic gratings, a tilted and axis-shift (TAS) Lloyd's mirror system was designed for recording such holographic gratings. The recording area will increase largely especially for gratings of low density, by setting the angle between the Lloyd's mirror and the substrate larger than 90°, and meanwhile, by enlarging the intersection angle of incident light and mirror surface. Insuring the projected area onto the substrate by reflex equal to the incident area directly onto the substrate, the optical axis was shifted to realize the maximization of utilization of interference area. The contrast of fringe pattern was analyzed by the coherence for the laser beam in the space and time scale. The TAS Lloyd's mirror system for 60 lines/mm grating in the contrast of 0.8 was optimized, and as a result, the interference area was increased by about 150 times comparing to the traditional Lloyd's mirror system using the Lloyd's mirror of same dimensions.     

曝光系统离焦对平面全息光栅衍射波前的影响

波前像差是衍射光栅的重要技术指标，它直接影响光栅的分辨率。由光致刻蚀剂记录两束相干光干涉条纹是制作全息光栅的关键步骤。为了提高全息光栅曝光系统调整精度、减小离焦、降低光栅的衍射波前像差，从离焦对反射球面准直镜的准直光平行度的影响程度出发，分析了准直光平行度对全息光栅衍射波前像差的影响。理论分析和数值模拟结果表明，准直镜调整误差直接决定全息光栅衍射波前像差大小。以3种不同刻线密度光栅为例，得出了准直镜调整误差的允许变化范围。     

Holographic grating recorded by He–Ne laser operating at 632.8 nm in polymer film containing push–pull azo dye

Holographic gratings were optically recorded by two beams from a He–Ne laser operating at 632.8 nm in poly (methyl methacrylate) (PMMA) film containing push–pull azo dye. The holographic characteristics of the recorded gratings were dependent on the polarization direction of the recording beams and the relationship between the diffractive signals and the power density of recording beams was investigated. The formation of holographic gratings accompanied by 532 nm (double-frequency of Nd:YAG laser) irradiation was studied in detail. It was found that the effect of 532 nm laser to the holographic grating lay in two aspects. The acceleration effect of 532 nm laser to the formation of holographic grating is predominant when the power density of 532 nm laser is low. While at relatively high power density of 532 nm laser, the erasure is the main factor to the holographic grating. Moreover, the holographic grating was probed by 532 nm laser at low power density and the dependence of the first order diffractive signal on the recording beam power density was also presented.     

软X射线全息平焦场光栅的条纹弯曲现象及其对光谱分辨率的影响

软X射线平焦场光栅光谱仪是等离子体诊断的重要仪器,其核心光学元件全息平焦场光栅通常采用非球面波记录光路制作,因此光栅条纹存在弯曲的现象.光栅条纹的弯曲会影响光谱成像质量,从而影响系统的光谱分辨率.记录光路的优化,只保证光栅子午面的线密度分布,因此优化的记录光路并不是惟一的,所以在保证子午面的线密度分布的同时能制作具有不同弯曲程度条纹的光栅.针对应用于0.8—6 nm的全息平焦场光栅,利用光线追迹方法分析了不同弯曲程度条纹光栅的光谱成像,发现采用柱面反射镜制作的接近于直条纹的光栅具有较好的光谱成像质量.相对于弯曲条纹的光栅,接近于直条纹的光栅理论光谱分辨率有明显的提高,入射波长为3 nm时,光谱分辨率从626提升到953,入射波长为5 nm时,光谱分辨率从635提高到1222.