AlGaN/AlN/GaN结构中二维电子气的输运特性

对使用金属有机物汽相沉积法生长的AlGaN/AlN/GaN结构进行的变温霍尔测量，测量结果指出在AlN/GaN界面处有二维电子气存在且迁移率和浓度在2K时分别达到了1.4×10⁴cm²·V^-1·s^-1和9.3×10¹²cm^-2，且在200K到2K范围内二维电子气的浓度基本不变，变磁场霍尔测量发现只有一种载流子(电子)参与导电.在2K温度下，观察到量子霍尔效应，Shubnikov-de Haas (SdH) 振荡在磁场约为3T时出现，证明了此结构呈现了典型的二维电子气行为.通过实验数据对二维电子气散射过程的半定量分析，推出量子散射时间为0.23ps，比以往报道的AlGaN/GaN结构中的散射时间长，说明引入AlN层可以有效减小合金散射，进一步的推断分析发现低温下以小角度散射占主导地位.     

金刚石薄膜中二次电子输运的蒙特卡罗模拟

本文通过编写的二维MATLAB蒙特卡罗程序, 对倍增的二次电子在金刚石薄膜中的输运特性进行了初步模拟. 研究表明: 二次电子的迁移率对温度和外加电场的大小很敏感, 在杂质浓度比较低时(<10¹⁷/cm^-3)受杂质浓度的影响不大. 模拟得到的 二次电子的饱和速度为1.88×10⁷ cm/s, 无外加电场时的迁移率为3732 cm² /V.s. 同时, 通过对二次电子束团在金刚石薄膜中的整体输运特性的模拟, 证明了束团电荷密度在应用要求的范围内时, 空间电荷力的影响可以忽略不计.     

利用交流阻抗谱揭示Ir(111)电极在酸性溶液中的氢吸附动力学

本文利用阻抗谱研究Ir(111)电极在HClO₄和H₂SO₄中溶液中的氢吸附行为. 在HClO₄溶液中,随着施加电位从0.2 V降到0.1 V(vs RHE),Ir(111)电极上氢吸附速率从1.74×10^-8 mol·cm^-2·s^-1增大到 3.47×10^-7 mol·cm^-2·s^-1 . 与相同条件下Pt(111)电极上的氢吸附速率相比,Ir(111)上的氢吸附速率要小1∽2个数量级,这是由于Ir(111)电极与H₂O结合能力更强,因此位于水合氢键网络中的氢离子需要克服更高的能垒才能重新定向进而发生欠电位沉积. 在H₂SO₄溶液中,氢吸附电位负移了200 mV,吸附速率也下降了一个数量级,这是由于Ir(111)电极表面强吸附的硫酸根/硫酸氢根物种的阻碍作用. 结果表明,在电化学环境下,位于电极表面附近的水分子的取代和重新定向在很大程度上影响了氢吸附过程.     

488 nm连续激光晶化本征非晶硅薄膜的喇曼光谱研究

利用等离子增强化学气相沉积系统制备了本征非晶硅薄膜,并选用488 nm波长的连续激光进行晶化.采用喇曼测试技术对本征非晶硅薄膜在不同激光功率密度和扫描时间下的晶化状态进行了表征,并用514 nm波长与488 nm波长对样品的晶化效果进行了比较.测试结果显示:激光照射时间60 s, 激光功率密度在1.57×10⁵ W/cm²时,能实现非晶硅向多晶硅的转变,在功率密度达到2.7 56×10⁵ W/cm²时,有非晶开始向单晶转变,随着激光功率密度的继续增加,晶化结果仍为单晶;在功率密度为2.362×10⁵ W/cm²下,60 s照射时间晶化效果较好;在功率密度为2.756×10⁵ W/cm²和照射时间为60 s的条件下,用488 nm波长比514 nm波长的激光晶化本征非晶硅薄膜效果较好,并均为单晶态.     

石墨烯/氧化铜纳米粒子/铜修饰电极对亚叶酸钙的电催化氧化及其分析应用

采用阳极极化的方法在铜电极表面形成氧化铜纳米粒子,然后采用循环伏安法将羧基化石墨烯电沉积到上述电极表面,成功制备了石墨烯/氧化铜纳米粒子/铜电极,用于碱性溶液中亚叶酸钙的检测.采用循环伏安法对亚叶酸钙在修饰电极上的催化氧化行为进行了研究,阳极扫描极化反向催化伏安法应用于亚叶酸钙的检测.在2.0×10^-7~2.0×10^-5 mol/L范围内,该电极显示出良好的线性关系,灵敏度为22.0 μA·μL/（μmol/cm²）,检测限达到7.6×10^-8 mol/L（S/N=3）,成功应用于实际样品的检测.     

一步掩膜法制备超低压ITO沟道纸上薄膜晶体管

基于一步掩模法工艺制备了一种新型的纸上双电荷层超低压薄膜晶体管. 在室温射频磁控溅射过程中, 仅仅利用一块镍掩模板, 就可同时沉积出氧化铟锡(ITO)源漏电极和ITO沟道. 在此基础上, 以等离子体增强化学气相沉积法(PECVD)合成的具有双电荷层效应的微孔SiO₂为栅介质, 成功制备出以纸为衬底的超低压氧化物薄膜晶体管. 这种晶体管显示出极好的性能: 超低的工作电压1.5 V, 场效应迁移率为20.1 cm²/Vs, 亚阈值斜率为188 mV/decade, 开关电流比为5× 10⁵. 这种基于全室温一步掩模法工艺制备的纸上氧化物薄膜晶体管具有工作电压低, 工艺简单, 成本低廉等优点, 非常有望应用于未来便携式低功耗电子产品的制造中.     

玻碳电极上ABTS的电化学行为

通过循环伏安法和旋转圆盘电极装置研究了2,2′-偶氮-双-(3-乙基苯并噻唑啉-6-磺酸)二铵盐(ABTS),ABTS^2-和ABTS^·-氧化还原对在pH=4.4的磷酸缓冲溶液中和玻碳电极上的电化学和传质行为. 由不同转速下记录的i-E曲线, 得到在磷酸缓冲溶液的电极反应速率常数和传递系数以及ABTS^2-的扩散系数分别为4.6×10^-3 cm/s、0.28和4.4×10^-6 cm^{2相似文献}   

采用二维坐标和变分方法计算磷烷阳离子的伞型振动

提出一个新的二维变分方法计算PH₃⁺(X²A₂")的对称伸缩振动(v1)和伞形振动(v2). 因为采用了对称化的笛卡尔坐标,所以动能项变得简单,同时伞形振动模式也能得到很好的反映. 相比采用经常使用的一维模型计算伞形振动,这个二维模型不需要约化质量的假设,同时也考虑了v1和v2振动模式之间的相互作用. 用二维模型对PH₃⁺首次进行了计算, 前七个能级的理论值和实验值的平均相对误差小于3 cm^{-1. 用相同的方法也计算了NH₃,结果没有PH₃+理想,说明这个方法有一定的局限性.}     

利用红外多光子解离光谱和理论计算揭示由脯氨酸和苯丙氨酸构成的质子化异源二聚体的结构

本文利用傅里叶变换离子回旋质谱仪和红外光学参量振荡器激光器相结合，在2700∽3700 cm^-1范围内获得了由脯氨酸和苯丙氨酸组成的质子化异源二聚体ProPheH⁺的红外多质子解离(IRMPD)光谱. 实验光谱表明，ProPheH⁺除了在3565 cm^-1处有一个对应于自由羧基O$-$H拉伸振动的吸收峰之外，在2935 cm^-1和3195 cm^-1处有两个宽吸收峰. 进一步对ProPheH⁺的结构在M062X/6-311++G(d,p)水平上进行了广泛的理论计算. 结果表明，其能量最稳定的构型具有电荷溶剂化结构，其中质子与脯氨酸单元结合. 这一构型的理论预测光谱与实验谱吻合较好.     

丰质子同位素65As的初步观察

使用20.11A MeV ⁶⁴Zn束轰击17.2mg/cm²的Be靶,初步观察到了丰质子同位素⁶⁵As.采用由磁分析器^[1]、PPAC、电离室和PSSD组成的探测系统,成功地鉴别了反应产物的电荷态、原子系数和质量数.     

Roles of Al-doped ZnO (AZO) modification layer on improving electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> thin film cathode

Al-doped ZnO (AZO) was sputtered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ (NCM) thin film electrode via radio frequency magnetron sputtering, which was demonstrated to be a useful approach to enhance electrochemical performance of thin film electrode. The structure and morphology of the prepared electrodes were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer, and transmission electron microscopy techniques. The results clearly demonstrated that NCM thin film showed a strong (104) preferred orientation and AZO was uniformly covered on the surface of NCM electrode. After 200 cycles at 50 μA μm^?1 cm^?2, the NCM/AZO-60s electrode delivered highest discharge capacity (78.1 μAh μm^?1 cm^?2) compared with that of the NCM/AZO-120s electrode (62.4 μAh μm^?1 cm^?2) and the bare NCM electrode (22.3 μAh μm^?1 cm^?2). In addition, the rate capability of the NCM/AZO-60s electrode was superior to the NCM/AZO-120s and bare NCM electrodes. The improved electrochemical performance can be ascribed to the appropriate thickness of the AZO coating layer, which not only acted as HF scavenger to keep a stable electrode/electrolyte interface but also reduced the charge transfer resistance during cycling.     

Preparation, characterization and electrochemical property of Sn-Fe-Mo-Al2O3 multi-phase composites

A novel technique has been developed to synthesize Sn-Fe-Mo-Al₂O₃, while nanoscale dispersion of a highly active tin phase was finely distributed in a stable inert multi-phase. The precursor was prepared by co-precipitation method with SnCl₄, FeCl₃, AlCl₃ and (NH₄)₆Mo₇O₂₄ as the raw materials. Sn-Fe-Mo-Al₂O₃ mixture was produced by reducing the precursor with H₂. The product was characterized by X-ray diffraction (XRD), ICP and scanning electron microscopy (SEM). The performance of the electrode was investigated. The Sn-Fe-Mo-Al₂O₃ electrode was found to have an initial charge capacity of over 461 mAh/g, and a reversible volumetric capacity of 2090 mAh/cm³, which is two times larger than that of graphite electrode (800 mAh/cm³). The coulomb efficiency in the first cycle was over 55%, but its cyclability was not improved significantly. In order to enhance the cycle performance, we investigated the anode after heat treated at 270 °C for 12 h. Under the same condition, the first charge-discharge characteristics were almost equivalent to the as-coated anode, and the retention capacity ratio after 20 cycles was improved from 41.1% to 86.5%. The heat-treated Sn-Fe-Mo-Al₂O₃ electrode exhibited better cycle life. The electrochemical reaction of the Sn-Fe-Mo-Al₂O₃ electrode with Li may obey the alloying-dealloying mechanism of Li_xSn(x?4.4) formation in the other tin-based electrodes.     

Rod-like polyaniline supported on three-dimensional boron and nitrogen-co-doped graphene frameworks for high-performance supercapacitors

In this work, novel three-dimensional (3D) boron and nitrogen-co-doped three-dimensional (3D) graphene frameworks (BN-GFs) supporting rod-like polyaniline (PANI) are facilely prepared and used as electrodes for high-performance supercapacitors. The results demonstrated that BN-GFs with tuned electronic structure can not only provide a large surface area for rod-like PANI to anchor but also effectively facilitate the ion transfer and charge storage in the electrode. The PANI/BN-GF composite with wrinkled boron and nitrogen-co-doped graphene sheets interconnected by rod-like PANI exhibits excellent capacitive properties with a maximum specific capacitance of 596 F/g at a current density of 0.5 A/g. Notably, they also show excellent cycling stability with more than 81% capacitance retention after 5000 charge-discharge cycles.     

LiFePO4在不同pH值水溶液中电化学性能表现及其衰减机理

LiFePO₄在含Li⁺水溶液中的电化学性能稳定性与水溶液的pH值密切相关,当溶液的pH值达到11后LiFePO₄在充放电循环过程中的容量衰减十分明显. 通过循环伏安测试、交流阻抗测试、电极充放电性能测试、非原位X射线衍射测试以及化学分析的方式对其容量衰减机理进行了研究. 结果表明LiFePO₄在pH=7的LiNO₃水溶液中具有相对最高的电化学稳定性,但是LiFePO₄材料在水溶液中较之其在有机电解液中依然会有较差的电化学性能表现. 认为LiFePO₄在水介质中的容量衰减现象归因于其在持续充放电过程中的Li、Fe、P溶解,同时电极表面也会附着一层沉淀物. 这些最终导致了材料晶体结构的破坏、电极极化的增大以及电极容量的衰减.     

Chitosan-ZnO/polyaniline ternary nanocomposite for high-performance supercapacitor

We report on the synthesis of chitosan-zinc oxide (ZnO)/polyaniline (CS-ZnO/PANI) ternary nanocomposites via in situ polymerization of aniline in the presence of CS-ZnO nanocomposite prepared by simple precipitation method. The structure, morphology, and physicochemical properties of prepared ternary composites are characterized by Fourier transform infrared, UV–visible, X-ray diffraction, SEM, EDXS, TEM, thermogravimetric/differential thermal analysis, and N₂ adsorption/desorption measurements. Their electrochemical properties are also investigated using cyclic voltammetry, galvanostatic charge–discharge tests, and electrochemical impedance spectroscopy. Electrochemical measurements show that the mesoporous CS_0.12-ZnO_2.5/PANI electrode yields larger specific capacitance (587.15 F g^?1) than the corresponding PANI-ZnO electrode without added chitosan and the capacitance retention is 80 % after 1,000 charge/discharge cycles at 175 mA cm^?2 current density in the voltage range of 0 to 0.8 V vs. SCE, due to the synergistic effect among three components which result in enhanced specific capacitance and cycling stability. The resulting composites are promising electrode materials for high-performance, environmentally friendly, and low-cost electrical energy storage devices.     

Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Effect of Na and Mn substitution in perovskite type LaFeO3 for storage device applications

The feasibility of perovskite-type La_0.8Na_0.2Fe_0.8Mn_0.2O₃ for structural, electrical, and electrochemical property for high rate capability in supercapacitor has been explored at room temperature. Nanocrystalline La_0.8Na_0.2Fe_0.8Mn_0.2O₃ was prepared via a modified Pechini route. Structural and surface morphology was done by X-ray diffraction and field emission scanning electron microscopy, respectively. Optical band gap was evaluated to be ∼1.59 eV. The bulk conductivity of the electrode under study was found to be ∼4.54 × 10⁻⁷S cm⁻¹. Specific surface area was found to be ∼8.16 m² g⁻¹. The electrode property has been studied via cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge-discharge analysis. The presence of a redox peak in cyclic voltammetry reveals typical pseudocapacitor behavior and recorded in the potential window −0.35 to 1 V. Faradic charge transfer resistance (R_ct) was found to be ∼53.85 Ω (R_s = 2.03 Ω) from EIS, and the charge-discharge characteristic for a hundred cycles shows an initial capacity fading up to 25 cycles, beyond which it becomes stable at ∼6.2 Fg⁻¹.

     

Electrochemical behavior of silicon compound in LiF–NaF–KF–Na<Subscript>2</Subscript>SiF<Subscript>6</Subscript> molten salt

The electrochemical reduction and nucleation process of Si⁴⁺ on an electrical steel electrode in the eutectic LiF–NaF–KF molten salt were investigated at 750 °C, by means of cyclic voltammetry and chronoamperometry technique. Silicon was electrodeposited on steel, and Fe₃Si was formed by the diffusivity of silicon on the electrode surface. The electrochemical reduction of Si⁴⁺ process in single-step charge transfer and the cathode process was reversible. The electrocrystallization process of silicon is controlled by progressive three-dimensional mechanism. The diffusion coefficient was calculated to be 5.42 × 10⁻⁷ cm²/s by chronopotentiometry at experimental conditions.     

Effective utilization of spray pyrolyzed CeO2 as optically passive counter electrode for enhancing optical modulation of WO3

Nanocrystalline cerium oxide (CeO₂) thin films were deposited onto the fluorine doped tin oxide coated glass substrates using methanolic solution of cerium nitrate hexahydrate precursor by a simple spray pyrolysis technique. Thermal analysis of the precursor salt showed the onset of crystallization of CeO₂ at 300 °C. Therefore, cerium dioxide thin films were prepared at different deposition temperatures from 300 to 450 °C. Films were transparent (T ~ 80%), polycrystalline with cubic fluorite crystal structure and having band gap energy (Eg) in the range of 3.04–3.6 eV. The different morphological features of the film obtained at various deposition temperatures had pronounced effect on the ion storage capacity (ISC) and electrochemical stability. The larger film thickness coupled with adequate degree of porosity of CeO₂ films prepared at 400 °C showed higher ion storage capacity of 20.6 mC cm^? 2 in 0.5 M LiClO₄ + PC electrolyte. Such films were also electrochemically more stable than the other studied samples. The Ce⁴⁺/Ce³⁺ intervalancy charge transfer mechanism during the bleaching–lithiation of CeO₂ film was directly evidenced from X-ray photoelectron spectroscopy. The optically passive behavior of the CeO₂ film (prepared at 400 °C) is affirmed by its negligible transmission modulation upon Li⁺ ion insertion/extraction, irrespective of the extent of Li⁺ ion intercalation. The coloration efficiency of spray deposited tungsten oxide (WO₃) thin film is found to enhance from 47 to 53 cm² C^? 1 when CeO₂ is coupled with WO₃ as a counter electrode in electrochromic device. Hence, CeO₂ can be a good candidate for optically passive counter electrode as an ion storage layer.     

Urea-assisted solvothermal synthesis of monodisperse multiporous hierarchical micro/nanostructured ZnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> microspheres and their lithium storage properties

High-quality monodisperse multiporous hierarchical micro/nanostructured ZnCo₂O₄ microspheres have been fabricated by calcinating the Zn_1/3Co_2/3CO₃ precursor prepared by urea-assisted solvothermal method. The as-prepared products are characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), and Brunauer-Emmett-Teller (BET) measurement to study the crystal phase and morphology. When tested as anode material for lithium ion batteries, the multiporous ZnCo₂O₄ microspheres exhibit an initial discharge capacity of 1,369 mAh g^?1 (3,244.5 F cm^?3) and retain stable capacity of 800 mAh g^?1 (1,896 F cm^?3) after 30 cycles. It should be noted that the good electrochemical performances can be attributed to the porous structure composed of interconnected nanoscale particles, which can promote electrolyte diffusion and reduce volume change during discharge/charge processes. More importantly, this ZnCo₂O₄ 3D hierarchical structures provide a large number of active surface position for Li⁺ diffusion, which may contribute to the improved electrochemical performance towards lithium storage.