Enhanced selectivity and sensitivity for inorganic anions using an ion-pairing reagent and sample stacking in capillary zone electrophoresis with direct UV detection

In this paper, the use of an ion-pairing reagent to improve the separation selectivity of inorganic anions in CZE was demonstrated by the addition of tetramethylammonium hydroxide (TMAOH) to the electrolyte. The separation of inorganic anions (Cl(-), I(-), Br(-), NO(2)(-), NO(3)(-) and SCN(-)) was performed using co-electroosmotic flow (EOF) with direct UV detection at 185 nm. The parameters affecting the mobility of the tested anions and the EOF such as the electrolyte pH and concentration of TMAOH in the electrolyte were examined to optimise the separation conditions. In addition, sample-stacking techniques were investigated to improve detection sensitivity. Detection sensitivities were improved 5-13-fold using electrokinetic sample stacking. The detection limits ranged from 1-3 micro mol L(-1). Finally, the proposed method was used for the separation of anions in groundwaters.     

Analysis of acrylamide in food products by in-line preconcentration capillary zone electrophoresis

Two in-line preconcentration capillary zone electrophoresis (CZE) methods (field amplified sample injection (FASI) and stacking with sample matrix removal (LVSS)) have been evaluated for the analysis of acrylamide (AA) in foodstuffs. To allow the determination of AA by CZE, it was derivatized using 2-mercaptobenzoic acid. For FASI, the optimum conditions were water at pH > or = 10 adjusted with NH3 as sample solvent, 35 s hydrodynamic injection (0.5 psi) of a water plug, 35 s of electrokinetic injection (-10 kV) of the sample, and 6s hydrodynamic injection (0.5 psi) of another water plug to prevent AA removal by EOF. In stacking with sample matrix removal, the reversal time was found to be around 3.3 min. A 40 mM phosphate buffer (pH 8.5) was used as carrier electrolyte for CZE separation in both cases. For both FASI and LVSS methods, linear calibration curves over the range studied (10-1000 microg L(-1) and 25-1000 microg L(-1), respectively), limit of detection (LOD) on standards (1 microg L(-1) for FASI and 7 microg L(-1) for LVSS), limit of detection on samples (3 ng g(-1) for FASI and 20 ng g(-1) for LVSS) and both run-to-run (up to 14% for concentration and 0.8% for time values) and day-to-day precisions (up to 16% and 5% for concentration and time values, respectively) were established. Due to the lower detection limits obtained with the FASI-CZE this method was applied to the analysis of AA in different foodstuffs such as biscuits, cereals, crisp bread, snacks and coffee, and the results were compared with those obtained by LC-MS/MS.     

CZE for the speciation of arsenic in aqueous soil extracts

We developed two separation methods using CZE with UV detection for the determination of the most common inorganic and methylated arsenic species and some phenylarsenic compounds. Based on the separation method for anions using hydrodynamic sample injection the detection limits were 0.52, 0.25, 0.27, 0.12, 0.37, 0.6, 0.6, 1.2 and 1.0 mg As/L for phenylarsine oxide (PAO), p-aminophenylarsonic acid (p-APAA), o-aminophenylarsonic (o-APAA), phenylarsonic acid (PAA), 4-hydroxy-3-nitrobenzenearsonic acid (roxarsone), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenite or arsenious acid (As(III)) and arsenate (As(V)), respectively. These detection limits were improved by large-volume sample stacking with polarity switching to 32, 28, 14, 42, 22, 27, 26 and 27 microg As/L for p-APAA, o-APAA, PAA, roxarsone, MMA, DMA, As(III) and As(V), respectively. We have applied both methods to the analysis of the arsenic species distribution in aqueous soil extracts. The identification of the arsenic species was validated by means of both standard addition and comparison with standard UV spectra. The comparison of the arsenic species concentrations in the extracts determined by CZE with the total arsenic concentrations measured by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) indicated that CZE is suited for the speciation of arsenic in environmental samples with a high arsenic content. The extraction yield of phenylarsenic compounds from soil was derived from the arsenic concentrations of the aqueous soil extracts and the total arsenic content of the soil determined by ICP-AES after microwave digestion. We found that 6-32% of the total amount of arsenic in the soil was extractable by a one-step extraction with water in dependence on the type of arsenic species.     

Determination of oxoanions in river water by capillary electrophoresis

A new capillary electrophoresis (CE) procedure was developed for simultaneous determination of ten oxoanions (CrO4(2-), SeO4(2-), MoO4(2-), WO4(2-), VO4(3-), SeO3(2-), As04(3-), TeO3(2-), TeO4(2-), and AsO3(3-)) which were baseline-separated from each other and from the interfering UV absorbing anions (NO3- and NO2-) commonly found in environmental water samples. The new background electrolyte system developed contained 5 mM potassium phosphate and 0.007 mM octadecyltrimethylammonium hydroxide, pH 11.2. The optimized working conditions were electrokinetic sampling at -5 kV for 10 s, running voltage at -15 kV with 5 microA current, and detection wavelength at 205 nm. No interference was observed for non-UV-absorbing anions and UV-absorbing anions up to 20 and 10 times higher concentrations respectively. The speed of analysis was fast, with a complete CE run within 6 min. Wide linear ranges (1-2,000 microg/L), good repeatability in migration time (relative standard deviation RSD 0.55-2.8%), satisfactory precision in peak area (RSD 3.8-5.6%) and peak height (RSD 3.9-5.3%) measurement, and detection limits (1-25 microg/L) sufficiently sensitive to detect oxoanions found in environmental water samples were obtained. The reliability of the CE procedure developed had been established by recovery test and parallel method determination using atomic absoprtion spectrophotometry for real river water sample.     

利用瞬间等速电泳的毛细管区带电泳大体积电动进样的研究

采用添加乙腈引发的场放大进样与瞬间等速电泳结合的预富集方法,实现了在毛细管内大体积高盐样品中阳离子的有效富集与分离。详细讨论了影响富集的缓冲体系、尾随离子种类、毛细管有效长度、进样时间和等速电泳时间等重要因素。选择在400 mmol/L LiAc-HAc缓冲液(pH 4.5)和400 mmol/L　β-丙氨酸-HAc尾随液(pH 4.5)及10 kV下样品和尾随溶液电动注入时间分别为270和90 s的条件下对高盐溶液中两种结构相近的药物普萘洛尔和美托洛尔进行了富集和分离。该方法富集倍数约为常规电动进样的280倍,普萘洛尔和美托洛尔的检出限分别为2×10-3和8×10-3 mg/L。     

毛细管电泳法测定水体中四环素类抗生素的基质效应及场放大进样技术的应用

比较了毛细管电泳（CE）和高效液相色谱（HPLC）技术对水体中4种四环素类抗生素（四环素、土霉素、金霉素及强力霉素）的分离效果。实验考察了水体的基质效应（pH值和水硬度）对分离的影响,优化了电泳条件,在压力进样模式（HDI）下,9.0 min内4种抗生素可达到基线分离,与HPLC相比,CE可以节省一半左右的分析时间。该方法具有良好的线性关系,检出限（LOD）在0.28~0.62 mg/L之间,迁移时间和峰面积的相对标准偏差（RSD）（n=6）分别为0.42%~0.56%及2.24%~2.95%;自来水和鱼塘水中加标回收率分别在96.3%~107.2%之间和87.1%~105.2%之间。此外,利用场放大电动进样（FASI）对目标物进行柱内预浓缩,检测灵敏度较HDI进样模式提高,LOD降至17.8~35.5 μg/L,迁移时间和峰面积的RSD（n=6）分别为0.85%~0.95%及1.69%~3.43%。CE具有样品前处理简单、分析速度快的特点,对环境水体中抗生素的检测具有明显的优势。     

Arsenic speciation based on ion exchange high-performance liquid chromatography hyphenated with hydride generation atomic fluorescence and on-line UV photo oxidation

An on-line method capable of the separation of arsenic species was developed for the speciation of arsenite As(III), arsenate As(V), monomethylarsenic (MMA) and dimethylarsenic acid (DMA) in biological samples. The method is based on the combination of high-performance liquid chromatograph (HPLC) for separation, UV photo oxidation for sample digestion and hydride generation atomic fluorescence spectrometry (HGAFS) for sensitive detection. The best separation results were obtained with an anion-exchange AS11 column protected by an AG11 guard column, and gradient elution with NaH2PO4 and water as mobile phase. The on-line UV photo oxidation with 1.5% K2S2O8 in 0.2 mol L(-1) NaOH in an 8 m PTFE coil for 40 s ensures the digestion of organoarsenic compounds. Detection limits for the four species were in the range of 0.11-0.15 ng (20 microL injected). Procedures were validated by analysis of the certified reference materials GBW09103 freeze-dried human urine and the results were in good agreement with the certified values of total arsenic concentration. The method has been successfully applied to speciation studies of blood arsenic species with no need of sample pretreatment. Speciation of arsenic in blood samples collected from two patients after the ingestion of realgar-containing drug reveals slight increase of arsenite and DMA, resulting from the digestion of realgar.     

Desorption electrospray ionization mass spectrometry (DESI-MS) applied to the speciation of arsenic compounds from fern leaves

The different chemical forms of arsenic compounds, including inorganic and organic species, present distinct environmental impacts and toxicities. Desorption electrospray ionization mass spectrometry (DESI-MS) is an excellent technique for in situ analysis, as it operates under atmospheric pressure and room temperature and is conducted with no/minimal sample pretreatment. Aimed at expanding its scope, DESI-MS is applied herein for the quick and reliable detection of inorganic (arsenate—As(V): AsO₄ ^3? and arsenite—As(III): AsO₂ ^?) and organic (dimethylarsinic acid—DMA: (CH₃)₂AsO(OH) and disodium methyl arsonate hexahydrate: CH₃AsO₃·2Na·6H₂O) arsenic compounds in fern leaves. Operational conditions of DESI-MS were optimized with DMA standard deposited on paper surfaces to improve ionization efficiency and detection limits. Mass spectra data for all arsenic species were acquired in both the positive and negative ion modes. The positive ion mode was shown to be useful in detecting both the organic and inorganic arsenic compounds. The negative ion mode was shown only to be useful in detecting As(V) species. Moreover, MS/MS spectra were recorded to confirm the identity of each arsenic compound by the characteristic fragmentation profiles. Optimized conditions of DESI-MS were applied to the analysis of fern leaves. LC-ICP-MS was employed to confirm the results obtained by DESI-MS and to quantify the arsenic species in fern leaves. The results confirmed the applicability of DESI-MS in detecting arsenic compounds in complex matrices.     

Sequential hydride generation/pneumatic nebulisation inductively coupled plasma mass spectrometry for the fractionation of arsenic and selenium species

The toxicity of certain elements is known to be related to their organic substituents and/or oxidation states. As such, total elemental determinations do not always yield sufficient information for accurate risk assessments and therefore speciation or fractionation data are required. In order to obtain fractionation data for trace levels of arsenic and selenium, a novel sequential pneumatic nebulisation (PN)/hydride generation (HG) inductively coupled plasma mass spectrometry (ICP-MS) method was developed. The method offers the advantage of sample introduction via either PN or HG by simply rotating a 4-way switching valve while the system is in operation. In PN mode, the liquid sample is aspirated into ICP, allowing for the determination of the total amount of each element, whilst in HG mode only the arsenic and selenium species that form volatile hydrides are determined. Conveniently, in the case of arsenic, this allows for differentiation between the four most toxic arsenic species (arsenate, arsenite, monomethylarsonic acid and dimethylarsinic acid), which form volatile hydrides, and the virtually non-toxic forms (arsenobetaine, arsenosugars, etc.), which do not. This allows for the rapid estimation of the amounts of toxic and non-toxic arsenic species present in a sample. For arsenic, the technique gave detection limits of 36 ng l⁻¹ in PN mode and 1 ng l⁻¹ in HG mode. For selenium, detection limits of 150 ng l⁻¹ were achieved in PN mode and 220 ng l⁻¹ in HG mode. The technique also gave good long- and short-term stabilities of under 6% RSD for both elements. A variety of samples, including water and urine standard reference materials, were analysed in both modes, and the precision and accuracy of the results for total arsenic and selenium levels were assessed. Using the technique in both modes also allowed for the fractionation of As and Se species into their volatile hydride-forming and non-hydride-forming species. This was particularly informative, with respect to As species present, in the case of a kelp powder extract. Digested tobacco samples were only analysed for their total As levels, in which case results obtained via both sample introduction modes showed good agreement.     

Field amplified sample injection-capillary electrophoresis-tandem mass spectrometry for the analysis of acrylamide in foodstuffs

This paper shows the applicability of capillary electrophoresis (CE) coupled to mass spectrometry (MS) for the analysis of acrylamide (AA) in foodstuffs. In order to obtain an ionisable compound amenable to be analysed by CE, acrylamide was derivatised with 2-mercaptobenzoic acid. Spectra in positive and negative modes were studied in order to select the best ionisation mode and multistep tandem mass spectrometry was used to obtain structural information. Maximum signal was observed when negative mode was used and MS/MS and MS3 were selected for quantitation and confirmation, respectively. For the separation, a fused-silica capillary of 80 cm and 50 microm I.D. and 35 mM ammonium formate/ammonia solution at pH 10 as running electrolyte were used. The applicability of field amplified sample injection (FASI) in reversed polarity was evaluated in order to decrease detection limits. The developed FASI-CE-MS/MS method provided a detection limit of 8 ng g(-1) and good linearity (r=0.999) and precision (day-to-day lower than 15%). The method has been applied to the analysis of different representative food products and the results were compared with those obtained by LC-MS/MS.     

Determination of anions using monolithic capillary column ion chromatography with end-to-end differential contactless conductometric detectors under resonance approach

An end-to-end differential measurement approach with capacitively coupled contactless conductivity detection (C(4)D) was applied to anion-exchange monolithic capillary column ion chromatography. The column was prepared by thermally initiated radical polymerization of poly(glycidyl methacrylate) in a fused-silica capillary of 320 μm i.d. and modified by quaternary ammonium latex surface coating. Two C(4)Ds were placed near both ends of the capillary column and the output difference between them was measured. With 15 mM potassium hydrogen phthalate used as the eluent, good separation of a mixture of inorganic anions (F(-), Cl(-), NO(2)(-), NO(3)(-)) was achieved. The detection limits of conventional C(4)D are 1.6, 0.28, 0.53, and 0.47 mg L(-1) for F(-), Cl(-), NO(2)(-), and NO(3)(-), respectively. To further enhance the sensitivity, the capacitive impedance from C(4)D was neutralized by an inductive impedance from a piezoelectric resonator. An increase in sensitivity by a factor of 7-8 was achieved in the resonating C(4)D in comparison with the conventional C(4)D. The detection limits of the resonating C(4)D are 0.23, 0.041, 0.065, and 0.059 mg L(-1) for F(-), Cl(-), NO(2)(-), and NO(3)(-), respectively. The response of the resonating C(4)D was analyzed based on an equivalent circuit model.     

Electrochemical measurement and speciation of inorganic arsenic in groundwater of Bangladesh

The presence of arsenic in groundwater above the maximum permissible limit of 50 mug l(-1) has threatened the health of more than 50 million people in Bangladesh and neighboring India. We report here the development of an inexpensive anodic stripping voltammetric (ASV) technique for routine measurement and speciation of arsenic in groundwater. The measurements are validated by more expensive atomic absorption, atomic emission and other techniques. To understand the present situation in Bangladesh, we measured As(III) in 960 water samples collected from 18 districts. A random distribution of 238 samples was used to measure both As(III) and As(V). The results from the present study indicate that most toxic form of inorganic arsenic, As(III), has the broad range of 30-98%. It shows 60% of the samples have 10 mug l(-1) and 44% of the samples have 50 mug l(-1) or more As(III). The fractional distribution pattern shows significant skew towards high percent occurrence which may indicate a progressive reduction process with a single source or a single mechanism for the formation of As(III). For direct consumption, this is possibly one of the most toxic groundwater known today. Speciation distribution at groundwater pH value shows H(3)AsO(3) is the predominant species including H(2)AsO(4)(-) and H(2)AsO(4)(2-) whose distribution is significantly pH dependent. This is also supported by E(h)-pH measurements. The depth distribution for Kushtia shows most of the As(III) is located within 100-200 ft deep aquifers. Similar fractional distribution of As(III) is found in deeper aquifers and may indicate contamination by leakage from upper aquifer. This study clearly demonstrates the aquifer environment is reductive and conducive to the formation of As(III) species.     

A new method to determine biological sample volume by short end multiple injection capillary electrophoresis: application in determination of nitrate and thiocyanate in human saliva

The aim of this study was to develop a simple and rapid method of capillary electrophoresis using a short end multiple injection in free solution to determine simultaneously the biological sample volume and analytes concentration. The method consists of a sequence of injection steps with an internal standard as the reference for correction of the volume of sample collected. The procedure was applies in the determination of NO(3)(-) and SCN in saliva samples. The background electrolyte was composed of 12 mM tris(hydroxymethyl)aminomethane and 8.5mM sulfuric acid, at pH 2.5. The internal standard used was BrO(3)(-). A fused silica capillary (48.5 cm total length, 8.5 cm effective length and 75 μm i.d.) coated with chitosan was used in a short-end injection configuration. Modification of the electroosmotic flow (EOF) using dynamic coating resulted in a controlled and stable EOF, contributing to the rapid separation of anions (0.36 min) in co-electroosmotic mode. The validation of the method for correcting the volume of saliva collected with a swab showed a difference of less than 3.5% compared with the predicted value and a correlation of 0.999. The limits of detection for NO(3)(-) and SCN(-) were 0.13 and 0.23 mg L(-1), respectively. The inter-day precision of the method determined for both analytes was less than 5% and the recovery ranged between 97 and 102%.     

On-line cryogenic trapping with microwave heating for the determination and speciation of arsenic by flow injection/hydride generation/atomic absorption spectrometry

An on-line flow injection-hydride generation/atomic absorption spectrometry method was developed for the preconcentration and selective determination of inorganic arsenic [As(III) and As(V)] and its methylated species. The separation of the arsenic species was performed by an automated pH-selective arsines generation technique, using sodium tetrahydroborate(III) as reductant. Each arsine was cryogenically trapped in a PTFE coil, knotted and sealed inside another wider diameter tube, through which liquid nitrogen was suctioned by negative pressure. Then, based on their different boiling points, the arsine species were selectively liberated by using a heating cycle of microwave radiation, followed by atomic absorption detection. A sample solution aliquot mixed with 1% citric acid was used for the determination of As(III) alone, while a second sample aliquot mixed with 2 mol l(-1) nitric acid was used for the quantitative determination of total inorganic arsenic, monomethylarsonic acid and dimethylarsinic acid. Based on 10 ml sample, the detection limits lie within the range 20-60 ng As l(-1), which are sufficiently low to detect the arsines-forming species in natural waters. These values are negatively affected by the reagents purity and background noise due to flame flickering, but the sensitivity can substantially be improved by increasing sample size or running several consecutive reactions.     

Determination of arsenic species in marine samples by HPLC-ICP-MS.

Arsenic speciation analysis in marine samples was performed using high performance liquid chromatography (HPLC) with ICP-MS detection. The separation of eight arsenic species viz. arsenite (As(III)), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenate (As(V)), arsenobetaine, trimethylarsine oxide (TMAO), arsenocholine and tetramethylarsonium ion (TeMAs) was achieved on a Shiseido Capcell Pak C18 column by using an isocratic eluent (pH 3.0), in which condition As(III) and MMA were co-eluted. The entire separation was accomplished in 15 min. The detection limits for 8 arsenic species by HPLC/ICP-MS were in the range of 0.02 - 0.10 microg L(-1) based on 3sigma of blank response (n=9). The precision was calculated to be 3.1-7.3% (RSD) for all eight species. The method then successfully applied to several marine samples e.g., oyster, scallop, fish, and shrimps. For the extraction of arsenic species from seafood products, the low power microwave digestion was employed. The extraction efficiency was in the range of 52.9 - 112.3%. Total arsenic concentrations were analyzed by using the microwave acid digestion. The total arsenics in the certified reference materials (DORM-2 and TORT-2) were analyzed and agreed with the certified values. The concentrations of arsenics in marine samples were in the range 6.6 - 35.1 microg g(-1).     

Optimization of HPLC-ICP-AES for the determination of arsenic species

High performance liquid chromatography coupled to ICP-AES detection provides a rapid, reliable and sensitive method for arsenic speciation. The separation of As(III), As(V), DMA and MMA was achieved with ion exchange chromatography coupled to an axially-viewed sequential ICP-AES. After optimization of the chromatographic parameters (pH and concentration of the mobile phase), a careful study of the interface was conducted. Five nebulizers associated to three spray chambers were tested. Response of the ICP to each arsenic species was strongly affected by the selection of the nebulizer and spray chamber, however similar responses were obtained for each arsenic species. Best signal-to-noise ratios were obtained by using a microconcentric nebulizer and a cyclone spray chamber and did not affect the chromatographic resolution. Detection limits better than 10 microg L(-1) were obtained for As(III), DMA, MMA and 20 microg L(-1) for As(V), which is a significant improvement over previously published results.     

Sulfur speciation by capillary zone electrophoresis: conditions for sulfite stabilization and determination in the presence of sulfate, thiosulfate and peroxodisulfate

Capillary zone electrophoresis (CZE) was used for the separation of the sulfur species SO3(2-), SO4(2-), S2O(3-) and S2O8(2-). Using an electrolyte system with 9.5 mmol L(-1) potassium chromate as UV-absorbing probe and 1 mmol L(-1) diethylenetriamine (DETA) as electroosmotic flow modifier, various possibilities for the stabilization of sulfite and electrophoretic separation of the sulfur anions were investigated. By adding 5% propanol as a stabilizer to both the working electrolyte and the sample solution, a good stabilization for sulfite and a separation of the sulfur anions in a short analysis time (4 min) was achieved. The advantages by using propanol instead of other stabilizers often used in analytical techniques are discussed. The electrophoretic separation of the sulfur anions was optimized with respect to the pH of the working electrolyte and concentration of the electroosmotic flow modifier (DETA). The detection limits achieved for SO3(2-), SO4(2-), S2O3(2-) and S2O8(2-) were 0.35, 0.25, 0.78 and 0.80 mg L(-1), respectively.     

Separation of organic and inorganic arsenic species by capillary electrophoresis using direct spectrophotometric detection

Capillary electrophoresis (CE) with UV detection was used for the determination of arsenite, arsenate, monomethylarsonic acid, dimethylarsinic acid, p-aminophenylarsonic acid, 4-hydroxy-3-nitrobenzenearsonic acid, 4-nitrophenylarsonic acid, phenylarsonic acid, and phenylarsine oxide. The electrophoretic mobilities of these anionic species were determined in a 20 mM phosphate buffer in a pH range from 4 to 11, which established pH 10 as the optimum for the separation. The target analytes were then separated in a fused-silica capillary using 20 mM NaHCO(3)-Na(2)CO(3) buffer, pH 10, as electrolyte and detected at 192 nm. Both normal- and reversed electroosmotic flow (EOF) separation modes were investigated and in the latter case, poly(diallydimethylammonium chloride) (PDDAC), was used for dynamic coating of the capillary and to provide a stable and reproducible reversed EOF (relative standard deviation RSD, 0.39%). The influence of electrolyte pH and composition, applied voltage, as well as EOF reversal protocols upon the method performance criteria were investigated. The optimised method provided limits of detection for the target analytes of 1.62, 6.22, 1.45, 1.83, 0.34, 0.40, 0.40, 0.18, and 0.30 mg/L As, respectively. Linearity was obtained in the range of 0.5-40 mg/L As (for aryl compounds) and from 5-100 mg/L As (for the remaining analytes). Reproducibility of peak areas was in the range of 0.8-5.5% RSD. The method was applied to the determination of four aryl arsenic compounds used as additives in animal feed. Analytes were extracted with 40 mM hydrochloric acid - acetonitrile 4:1 v/v, and then cleaned up by passing through a C(18) solid-phase extraction cartridge before analysis by CE with detection at 200 nm. Recoveries for the four analytes were in the range of 78.8-108.3%.     

微波酸提取/液相色谱-电感耦合等离子体质谱法测定动物源性中药中6种砷形态

建立了微波酸提取/液相色谱-电感耦合等离子体质谱联用(LC-ICP-MS)测定动物源性中药中6种砷形态(亚砷酸盐As(Ⅲ),砷酸盐As(V),一甲基砷MMA,二甲基砷DMA,砷甜菜碱As B和砷胆碱As C)的分析方法。采用1%HNO_3溶液在80℃微波提取10 min,经离心分层,过固相萃取SEP C18柱和0.45μm滤膜,以25 mmol/L NH_4H_2PO_4溶液(p H 6.7)-乙醇(99∶1,体积比)为流动相进行等度洗脱,各砷形态在10 min内实现基线分离。结果显示,6种砷形态在1.0~100.0μg/L范围内线性关系良好,相关系数为0.999 5~0.999 7,方法检出限(LOD)为0.24~1.0μg/kg,相对标准偏差(RSD)为0.96%~2.0%。将方法应用于地龙、水蛭、海螵蛸、桑螵蛸、石决明和鸡内金中6种砷形态的测定,加标回收率为94.2%~103.8%,提取效率为95.5%~102.8%,优于热提取法。方法快速、准确、重现性好,适用于动物源性中药及类似样品中的砷元素形态分析及质量监控。     

Stability study of As(III), As(V), MMA and DMA by anion exchange chromatography and HG-AFS in wastewater samples

The stability of arsenic species (arsenate [As(V)], monomethylarsonate [MMA], dimethylarsinate [DMA] and arsenite [As(III)]) in two types of urban wastewater samples (raw and treated) was evaluated. Water samples containing a mixture of the different arsenic species were stored in the absence of light at three different temperatures: +4 degrees C, +20 degrees C and +40 degrees C. At regular time intervals, arsenic species were determined by high performance liquid chromatography (HPLC)-hydride generation (HG)-atomic fluorescence spectrometry (AFS). The experimental conditions for the separation of arsenic species by HPLC and their determination by AFS were directly optimised from wastewater samples. As(III), As(V), MMA and DMA were separated on an anion exchange column using phosphate buffer (pH 6.0) as the mobile phase. Under these conditions the four arsenic species were separated in less than 10 min. The detection limits were 0.6, 0.9, 0.9 and 1.8 micro g L(-1) for As(III), DMA, MMA and As(V), respectively. As(V), MMA and DMA were found stable in the two types of urban wastewater samples over the 4-month period at the three different temperatures tested, while the concentration of As(III) in raw wastewater sample decreased after 2 weeks of storage. A greater stability of As(III) was found in the treated urban wastewater sample. As(III) remained unaltered in this matrix at pH 7.27 over the period studied, while at lower pH (1.6) losses of As(III) were detected after 1 month of storage. The results show that the decrease in As(III) concentration with time was accompanied by an increase in As(V) concentration.