超声提取-高温燃烧吸收-离子色谱法测定纺织品中可吸附有机卤化物北大核心CSCD

建立了一种对纺织品中可吸附有机卤化物(AOX)的超声提取-高温燃烧吸收-离子色谱定量检测分析新方法。该方法采用超声方式提取纺织品中的AOX,提取液加入活性炭进行振荡吸附,并用酸性硝酸钠溶液对无机卤化物进行去除。采用程序升温的氧化燃烧方式对吸附AOX的活性炭进行裂解、燃烧及气化,其产生的卤化氢等气体随载气进入吸收液并完全转化为无机卤素阴离子,采用离子色谱分离测定,外标法定量。实验优化了超声提取时间、活性炭用量、燃烧气及其流量、燃烧升温程序、吸收液和吸收方式等前处理条件,并对离子色谱的仪器分析条件如色谱柱、柱温及淋洗液流速等进行优化。结果表明,氟、氯、溴、碘4种卤素离子的标准溶液在0.02~10 mg/L范围内呈线性关系,线性相关系数(R^(2))均在0.999以上;AOX测定的方法定量限为0.10~0.50 mg/kg。以棉、毛和涤纶3种不同种类的阴性纺织样品作为样品基质,选取典型的有机卤化物进行加标,在低、中、高3个加标水平下测得AOX的平均回收率为82.3%~98.7%,相对标准偏差(RSD,n=7)为2.0%~5.7%,表明方法具有良好的回收率和精密度。将该方法应用于实际纺织样品的测定,检出了不同含量的AOX,且重复性好。研究建立的方法通过采用活性炭的振荡吸附、程序升温的高温氧化燃烧方式和多孔吸收瓶的二级吸收方法,提高了AOX转化为无机卤素的回收率;同时利用离子色谱仪器选择性好、灵敏度高的特点成功地一次性分离检测4种AOX,且无杂质离子的干扰。该方法简单、准确、可靠,满足国内外法规和标准对纺织品中AOX的限量要求,适用于纺织品中AOX的分析测定。     

氧弹燃烧-离子色谱法测定电子产品中卤素

采用氧弹燃烧法对试样进行燃烧,然后用水作为吸收液进行吸收,提出了离子色谱法分离测定电子产品中卤素含量的方法。以Metrosep A Supp 4型阴离子分析柱为离子交换柱,以1.8mmol·L~(-1)碳酸钠-1.7mmol·L~(-1)碳酸氢钠溶液为淋洗液等度洗脱。3种卤素离子氟离子、氯离子和溴离子的方法检出限(3S/N)依次为4.0,5.6,20.5μg·L~(-1)。该方法已用于电子产品中卤素的测定。     

高温燃烧-离子色谱测定导电胶中氯和溴

采用高温燃烧吸收仪与离子色谱仪联用技术，建立了测定导电胶中卤素含量的方法。优化的实验条件为：燃烧炉温度为800℃，样品质量为0.1 g，以0.05 mol/L氢氧化钠为吸收液，0.02 mol/L氢氧化钾为淋洗液，采用抑制型电导检测器检测。氯、溴离子质量浓度在1～50 mg/L范围内与对应色谱峰面积线性关系良好，氯离子的线性相关系数r=0.999 7，检出限为5.4 mg/kg，加标的平均回收率为101.2%；溴离子线性相关系数r=0.999 7，检出限为8.6 mg/kg，加标的平均回收率为100.2%。与传统氧弹燃烧-离子色谱法相比，该法无需对样品进行固化处理，进样方便、快捷，可用于导电胶样品中卤素含量的测定。     

高温裂解-离子色谱法测定煤中卤素的含量

建立高温裂解-离子色谱联用技术检测煤中卤素含量的方法。煤样30.0~40.0 mg在350 mL·min~(-1)富氧条件下经1 100℃高温裂解处理后,含卤素组分转化成气体形式被20 mmol·L~(-1)氢氧化钠溶液5 mL吸收后,采用离子色谱电导检测器和IonPac AS18柱测定吸收液中氟、氯和溴的含量,采用离子色谱安培检测器和Ionpac AS11-HC柱测定吸收液中碘离子的含量。结果表明,氟、氯、溴和碘的质量浓度在一定范围内与其峰面积呈线性关系,检出限(3s)分别为3.03,2.47,0.80,8.85 mg·kg~(-1)。精密度试验结果显示测定值的相对标准偏差(n=9)均小于5.0%。按标准加入法对煤样进行回收试验,回收率在83.6%~105%之间。     

高温裂解-离子色谱法测定煤中卤素的含量北大核心CSCD

建立高温裂解-离子色谱联用技术检测煤中卤素含量的方法。煤样30.0~40.0 mg在350 mL·min^(-1)富氧条件下经1 100℃高温裂解处理后,含卤素组分转化成气体形式被20 mmol·L^(-1)氢氧化钠溶液5 mL吸收后,采用离子色谱电导检测器和IonPac AS18柱测定吸收液中氟、氯和溴的含量,采用离子色谱安培检测器和Ionpac AS11-HC柱测定吸收液中碘离子的含量。结果表明,氟、氯、溴和碘的质量浓度在一定范围内与其峰面积呈线性关系,检出限(3s)分别为3.03,2.47,0.80,8.85 mg·kg^(-1)。精密度试验结果显示测定值的相对标准偏差(n=9)均小于5.0%。按标准加入法对煤样进行回收试验,回收率在83.6%~105%之间。     

有机化合物中碳、氢、氯、硫的综合测定

1910年普利格尔(Pregl)发明了有机化合物中元素的定量分析的方法。他使样品与氧化剂在高温下燃烧,吸收、称量产生的水及二氧化碳,从而求得碳、氢的含量。后来 M.柯尔苏(Коршун)改进了这个方法,他不用氧化剂,使样品单独在石英管中通氧燃烧,可以加快燃烧时间;而且除开碳、氢之外还可同时分析样品中的卤素或硫。同时分析碳、氢、卤素(或硫)的方法是在燃烧管外连接一个装有银丝或银网的石英套管,将这套管加热至450°,可全部吸收卤化物。若要吸收硫化物则需加热至750°。柯尔苏的空管法有它的优点,但对于同时测定几种元素来说,则仍旧不够完善。因为:(1)石英的卤素、硫吸收管经多次加热将呈     

钙掺杂对La2-xCaxCe2O7-δ性能影响研究

利用高温固相反应法制备了高温质子导体La2-xCaxCe2O7-δ(0≤x≤0.2)。分别利用X射线衍射(XRD)、扫描电子显微镜(SEM)对试样的相组成、微观形貌进行了表征。并对试样在水蒸气和CO2气氛中的化学稳定性进行了测试。研究了不同掺杂量和不同测试气氛对La2-xCaxCe2O7-δ电性能的影响。实验结果表明:1 500℃烧结的试样均形成萤石型结构;试样在CO2和水蒸气气氛中表现出良好的化学稳定性。试样在湿润氢气气氛下的电导率明显高于干燥空气气氛,x=0.1的试样在湿润氢气气氛中具有最高的电导率,850℃时达到3.16×10-2S.cm-1,电导活化能为84.93 kJ.mol-1。     

氧弹燃烧-离子色谱法测定高分子聚合物的卤素离子

采用氧弹燃烧法对塑料样品进行燃烧,用碳酸钠作为吸收液进行吸收,建立了离子色谱法分离测定微量卤素离子的方法.离子色谱条件为:IonPac AS22离子交换柱,碳酸盐等度淋洗,抑制型电导检测.用该方法对塑料颗粒和塑料瓶盖中的氯离子进行测定,加标回收率分别为92.25%～95.68%、92.37% ～95.52%.     

在线燃烧-离子色谱法测定炭黑中氯和溴的含量

<正>炭黑是橡胶产品的补强填充剂,是仅次于生胶的第二橡胶原材料,炭黑是有机物在空气不足的条件下经不完全燃烧或热分解而得到的有机产物[1-3]。卤素化合物作为一种阻燃剂,广泛应用于各类高分子材料中[4]。根据国际电工委员会IEC 61249-2-21标准,卤素的限制适用于氯和溴,其他的元素没有限制[5]。卤素化合物在环境中具有生物累计性,对环境有持续性的伤害,同时可能会对人体的免疫和再生     

无机固体样品中硫的测定方法的研究进展

综述了无机固体样品中硫的高温燃烧热解(包括燃烧-红外吸收法、燃烧-碘量法、燃烧-库仑滴定法、燃烧-中和滴定法和燃烧-电导法等)、湿法消解(包括硫酸钡重量法、硫酸钡比浊法、电感耦合等离子体原子发射光谱法、电感耦合等离子体质谱法、原子吸收光谱法和离子色谱法等)和固体样品直接分析(包括火花源原子发射光谱法、辉光放电原子发射光谱法、X射线荧光光谱法等)等3类测定方法的研究进展(引用文献117篇)。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.