以卵磷脂为手性添加剂制备手性介孔二氧化硅

以十六烷基三甲基溴化铵(CTAB)的自组装体为模板,卵磷脂(PC)为手性添加剂,在n PC∶nCTAB=1∶21时,通过溶胶-凝胶法制备了螺旋介孔二氧化硅纳米棒。利用扫描电镜(FESEM)、透射电镜(TEM)、X-射线衍射以及氮气吸附-脱附等测试手段,对该纳米棒的形貌以及孔结构进行了表征。TEM显示该纳米棒的长度约为50～200 nm,直径约为30～50 nm。X-射线衍射表明孔道呈二维六方排列,虽然FESEM显示纳米棒左右手比例约为1∶1,但通过圆二色谱表征证明该纳米棒在埃尺度下倾向于形成单一手性。结果表明,卵磷脂的手性可以传递到螺旋介孔二氧化硅纳米棒中。     

以联二萘酚衍生物为手性添加剂制备介孔二氧化硅

通过溶胶-凝胶法以十八烷基三甲基溴化铵（STAB）自组装体为模板和非离子型联二萘酚衍生物（S）作为手性添加剂制备螺旋介孔二氧化硅。样品利用扫描电镜、透射电镜、X-光衍射以及氮气吸附-脱附进行了表征。结果表明：反应混合物中S与STAB的物质的量之比对介孔二氧化硅的形貌及孔结构有很大影响。改变n_S：n_STAB比,从0.1：1到0.4：1时,其结构从螺旋纳米棒状变为表面具有环形层状孔的纳米棒,孔道由沿着纳米棒长轴方向转变为同心环状。当n_S：n_STAB=0.5：1时,得到类似皱缩花瓣的纳米颗粒。该手性添加剂的引入并没有改变左右手螺旋纳米棒的比例。     

以联二萘酚衍生物为手性添加剂制备介孔二氧化硅

通过溶胶-凝胶法以十八烷基三甲基溴化铵(STAB)自组装体为模板和非离子型联二萘酚衍生物(S)作为手性添加剂制备螺旋介孔二氧化硅。样品利用扫描电镜、透射电镜、X-光衍射以及氮气吸附-脱附进行了表征。结果表明:反应混合物中S与STAB的物质的量之比对介孔二氧化硅的形貌及孔结构有很大影响。改变nS∶nSTAB比,从0.1∶1到0.4∶1时,其结构从螺旋纳米棒状变为表面具有环形层状孔的纳米棒,孔道由沿着纳米棒长轴方向转变为同心环状。当nS∶nSTAB=0.5∶1时,得到类似皱缩花瓣的纳米颗粒。该手性添加剂的引入并没有改变左右手螺旋纳米棒的比例。     

CaCO3纳米微粒的层状液晶模板法制备及其生长过程中的形貌演变

在Triton X-100/n-C₁₀H₂₁OH/H₂O体系中，低角X射线衍射测试表明层状液晶的溶剂层厚度小于3 nm。利用层状液晶为模板制备了CaCO₃纳米微粒，并用透射电子显微镜(TEM)、X射线衍射(XRD)和选区电子衍射(SAED)进行了表征。TEM结果表明所得CaCO₃纳米粒子的形貌为球形，粒径在2～8 nm，分布较窄。XRD表明CaCO₃纳米微粒的物相为方解石型和球霰石型混合结构。在制备过程中，Ca(OH)₂的加入和CaCO₃纳米微粒的析出并未破坏层状液晶的对称性和长程有序性。此外，在Triton X-100/CH₃CH₂OH体系中，研究了CaCO₃纳米微粒的生长行为，发现小的纳米微粒先通过导向聚集生长成小的梭状物，然后小的梭状物继续生长，最后发生Ostwald陈化形成较为均一的两头尖的带状纳米结构，其宽度在50～200 nm，长度约为2 μm。     

立方介孔相含钕氧化硅的合成与表征

以十六烷基三甲基溴化铵为结构导向剂，通过水热法合成了具有立方结构的含钕Nd-MCM-48介孔分子筛材料。XRD和TEM测试表明当n_Nd/n_Si<0.05时可以获得典型的长程有序介孔立方结构相，随n_Nd/n_Si比的增加，晶胞参数的增大和红外吸收光谱(FT-IR)的变化为Nd进入介孔分子筛骨架中提供了有力证据。N₂吸附-脱附实验给出了其BET表面积为1 195 m²·g^-1，BJH平均孔径为3.6 nm。紫外-可见漫反射光谱(UV-Vis)证明钕氧形成一种八面体结构。X射线光电子能谱(XPS)进一步证明钕主要以三价形式存在于立方介孔分子筛骨架中。     

1-[4-(二甲氨基)苯亚甲基氨基]-4-苯基硫脲的合成及手性晶体结构

对二甲氨基苯甲醛和苯基氨基硫脲缩合反应生成对二甲氨基苯甲醛缩氨基苯硫脲{1-[4-(dimethylamino)ben- zylidene]-4-phenylthiosemicarbazide}, 并从溶液中析出手性晶体. 元素分析、红外光谱、紫外光谱、核磁谱、质谱和X射线衍射测定其组成和结构. 晶体属正交晶系, P2₁2₁2₁空间群, a＝0.77038(14) nm, b＝1.1428(2) nm, c＝1.6726(3) nm, V＝1.4726(5) nm³, Z＝4, D_c＝1.346 g/cm³, F(000)＝632, μ＝0.219 mm^－1, 可观测点精修最终偏离因子: R＝0.0407, wR＝0.1157. 化合物的晶体结构和固态圆二色谱表明化合物在结晶过程中发生单一对映体的手性堆积.     

FexOy/SBA-15介孔分子筛的合成以及性能研究

在酸性溶液中利用溶胶凝胶-pH值控制两步法直接合成Fe_xO_y/SBA-15介孔分子筛，同时利用场发射扫描电子显微镜(FESEM)、小角度X射线衍射(Low-angle XRD)、透射电子显微镜(TEM)以及振动样品磁强计(VSM)对制备的各种SBA-15介孔分子筛进行结构以及性能的测试、表征。结果显示Fe_xO_y均匀地分散在SBA-15的骨架中，而且会对SBA-15介孔分子筛起钉轧作用。而后着重研究了Fe_xO_y的加入对SBA-15介孔分子筛的热稳定性、催化特性以及磁学性能的影响。Fe_xO_y的引入可以增加制备的SBA-15介孔分子筛的热稳定性;Fe_xO_y的引入可以改善SBA-15介孔分子筛的催化活性，得到了开口的、石墨化程度较好的纳米碳管。Fe_xO_y的引入使SBA-15介孔分子筛具有明显的铁磁性。     

1-[4-(二甲氨基)苯亚甲基氨基]-4-苯基硫脲的另一个手性对映体晶体结构

对-二甲氨基苯甲醛和苯基氨基硫脲缩合反应生成1-[4-(二甲氨基)苯亚甲基氨基]-4-苯基硫脲(DMB), 产物能从溶液中析出单一手性对映体晶体. 用单晶X射线衍射技术测定了它的绝对构型, 晶体属正交晶系, P2₁2₁2₁空间群, a＝0.7870(2) nm, b＝1.1560(2) nm, c＝1.6668(3) nm, V＝1.5164(5) nm³, Z＝4, D_c＝1.307 g/cm³, F(000)＝632, μ＝0.213 mm^－1, 2557个可观测点[I＞2s(I)]精修的最终残差因子: R＝0.0409, wR＝0.1061, Flack参数为0.00(9), 能够确定绝对构型. 化合物的晶体结构和大宗粉末样品的固体圆二色谱表明化合物在结晶过程中发生单一对映体的手性堆积.     

导电高分子PEDOT/PSS稳定的Pt3Co纳米粒子的制备及电、磁性

利用一步共还原法在导电高分子聚二氧乙基噻吩/聚对苯乙烯磺酸(PEDOT/PSS)水溶液中合成了磁性纳米复合物Pt₃Co-PEDOT/PSS. 利用透射电镜(TEM)、X射线衍射(XRD)、拉曼光谱、超导量子干涉仪(SQUID)对其进行了表征.结果表明Pt₃Co纳米粒子为面心立方结构(fcc), 粒子平均粒径为9.6 nm, 标准偏差为2.4 nm. 用旋转涂膜法制备的Pt₃Co-PEDOT/PSS薄膜导电率()在1.6～4.0 S/cm之间. 当温度在阻塞温度(T_B, 110.5 K)以上时, 纳米复合物Pt₃Co-PEDOT/PSS显示出超顺磁性, 低于T_B时呈铁磁性, 在5 K时其剩磁(M_r)和矫玩力(H_c)分别为4.1 emu/g和701 Oe(奥斯特).     

介孔硅铝酸盐的合成及其在傅克反应中的催化性能

采用溶胶凝胶法合成了一系列有序性好且酸性较强的介孔硅铝酸盐材料。利用X射线粉末衍射(XRD)、透射电镜(TEM)、²⁷Al核磁共振(²⁷Al NMR)、氨气程序升温脱附(HN₃-TPD)及吡啶吸附红外光谱(Py-FT-IR)对制备的介孔硅铝酸盐材料的结构和性能进行表征,并考察了材料在苯甲醚和苯甲醇的傅克烷基化反应中的催化活性。实验结果表明：合成过程中,表面活性剂的用量、硅铝物质的量的比会影响材料结构的有序性,醋酸用量对材料结构有序性影响很小;进一步研究结果表明,n_Si / n_Al比会影响材料的酸催化活性,当n_Si / n_Al=10时材料的酸催化活性最高。氨气程序升温脱附和吡啶吸附红外光谱表明n_Si / n_Al=10的材料含有最多的B酸酸量。     

Facile synthesis of mesoporous silica nanoparticles with controlled morphologies using water–acetone media

Mesoporous silica nanoparticles with controlled morphologies including nanococoons, nanorods and nanospheres have been synthesized in water–acetone media at room temperature using cetyltrimethylammonium bromide (CTAB) as the template. The obtained nanoparticles generally show hexagonal-like mesoporous structures with average pore size ranging from 2.7 to 3.3 nm and surface area from 806 to 1055 m²/g, respectively. It was found that the changes in water-to-acetone molar ratios have a dramatic impact on the morphologies of the mesoporous silica with different surface roughness, probably due to the solvent influence on the rate of the hydrolysis of tetraethoxy silane (TEOS) and the polymerization of inorganic species. Interestingly, the morphology of the mesoporous silica products can be controlled in shape from nanococoons to nanorods to nanospheres just by decreasing the water-to-acetone molar ratio from 75 to 30 to 15, respectively. From transmission electron microscopy (TEM) images, it was observed that mesoporous parallel channels run along the short axis in some areas in the nanorods, whereas the radially arranged mesopore channels are present in the nanospheres. Additionally, hydrothermal treatment leads to rougher surfaces while retaining the morphologies and nanostructures of these mesoporous silicas.     

Synthesis of hollow spherical silica with MCM-41 mesoporous structure

Hollow spherical mesoporous silica was synthesized by using sodium silicate as a precursor and a low concentration of cetyltrimethylammonium bromide (CTAB) (0.154 mol dm^–3). The resulting hollow spherical particles were characterized with scanning electron microcopy (SEM), small-angle X-ray diffraction (SXRD), transmission electron microscopy (TEM), and N₂ gas adsorption and desorption techniques. The results showed that regular spherical mesoporous silica could be obtained only if the molar ratio of propanol to CTAB was in the range of approximately 8:1–9:1. The spherical particles were hollow (inside), and the shell consisted of smaller particles with a pore structure of hexagonal symmetry. With an increase of the molar ratio of propanol to CTAB, the distance (a value) between centers of two adjacent pores increased, and the pore structure of mesoporous silica became less ordered. N₂ adsorption–desorption curves revealed type IV isotherms and H1 hysteresis loops; with an increase of the molar ratio of propanol to CTAB, the pore size with Barrett–Joyner–Halenda (BJH) diameter of the most probable distribution decreased, but the half peak width of the pore size distribution peak increased     

Preparation of Mesoporous 1,4‐Phenylene‐silica Nanorings through a Dual‐templating Approach

Mesoporous 1,4‐phenylene‐silica nanorings were prepared using cetyltrimethylammonium bromide (CTAB) and (S)‐2‐methyl‐1‐butanol as a chiral dopant in concentrated aqueous NH₃ solutions. Transmission electron microscopy images of the samples indicated that the nanorings were formed by bending nanorods 360°. With increasing the stirring speed or the (S)‐2‐methyl‐1‐butanol/CTAB molar ratio, the morphologies of mesoporous 1,4‐phenylene‐silicas changed from helical nanofibers to nanorings, and then to nano‐saddles. Circular dichroism spectra of these hybrid silicas indicated that they were chiral.     

Characterization Studies on the Ionic Liquid-Templated Mesoporous Silica with Wormlike Pores

This article reports a novel preparation of wormlike mesoporous silica with 1-hexadecane-3-methylimidazolium bromide (C₁₆MIM)Br, a kind of room-temperature ionic liquids (RTILs), as a template via a sol-gel nanocasting technique. The characterization studies were carried out in contrast with that of the mesoporous silica with cetyltrimethylammonium bromide (CTAB), a usually used template, which has the same alkyl chain length with (C₁₆MIM)Br. The structures of the silica materials have been characterized by Transmission electron microscopy (TEM), High-resolution TEM (HRTEM) and N₂ adsorption-desorption measurements. The results show that both the mesoporous materials prepared with different templates respectively can form regular wormlike mesopores with ca. 2 nm in pore diameter. They also have large BET surface areas with narrow size distribution. Compared to the CTAB-template mesoporous silica, the material with (C₁₆MIM)Br as a template has highly uniform pore size and larger surface area. In addition, the formation mechanism of the wormlike mesopores with RTIL has been proposed by an electrostatic charge matching assembly-pathway and steric factor.     

二元阴阳离子表面活性剂法合成介孔氧化硅囊泡

以十二烷基磺酸钠(SDS)和十六烷基三甲基溴化铵(CTAB)为表面活性剂, 在SDS与CTAB的摩尔比为1.0~2.3时, 以正硅酸乙酯(TEOS)为硅源, 在氨水-水体系中于68℃下合成介孔氧化硅囊泡. 通过透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 热重分析仪(TGA)和氮气吸附-脱附实验仪对合成的产物进行表征. 结果表明, 合成的产物为介孔氧化硅囊泡聚集体, 孔径约为4 nm, 样品的Brunauer-Emmett-Teller(BET)比表面积为826 m²/g. 对介孔氧化硅囊泡的形成机理做了初步探讨.     

Effect of salts on synthesis of mesoporous materials with mixed cationic and anionic surfactants as templates

Mesoporous silica materials were synthesized using tetraеthoxysilane as precursor and liquid crystals formed in aqueous mixtures of cetyl trimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) as templates, without and with the addition of NaBr or Na₂SO₄. For this purpose, the formation of liquid crystals as a function of the ratio of CTAB and SDS under different conditions was studied. It was found that liquid crystals formed in the mixed system of CTAB and SDS at certain mixing ratios are well-structured templates for the synthesis of mesoporous silicas. The synthesized silica materials were characterized by transmission electron microscope and nitrogen adsorption/desorption analysis. The pore size of mesoporous silicas could be controlled between 3 to 6 nm by simply changing the concentration of NaBr in solution. The mesoporous silicas exhibited lamellar structure and the order of structural arrangement was promoted with addition of NaBr. However, addition of Na₂SO₄ led to ink-bottle type pores of mesoporous silica with a narrow pore size distribution of around 2 nm and a higher specific surface area of 610 m² g^–1.     

Preparation of mesoporous submicrometer silica capsules via an interfacial sol-gel process in inverse miniemulsion

Mesoporous silica capsules with submicrometer sizes were successfully prepared via the interfacial hydrolysis and condensation reactions of tetraethoxysilane (TEOS) in inverse miniemulsion by using hydrophilic liquid droplets as template. The inverse miniemulsions containing pH-controlled hydrophilic droplets were first prepared via sonication by using poly(ethylene-co-butylene)-b-poly(ethylene oxide) (P(E/B)-PEO) or SPAN 80 as surfactant. TEOS was directly introduced to the continuous phase of an inverse miniemulsion. The silica shell was formed by the deposition of silica on the surface of droplets. The formation of capsule morphology was confirmed by transmission electron microscopy (TEM) and field emission scanning electron microscopy (FESEM). The mesoporous structure was verified by nitrogen sorption measurements. The specific surface area could be tuned by the variation of the amount of cetyltrimethylammonium bromide (CTAB) and TEOS, and the pore size by the amount of CTAB. The influences of synthetic parameters on the particle size and morphology were investigated in terms of the amount of CTAB, pH value in the droplets, TEOS amount, surfactant amount, and type of solvent with low polarity. A formation mechanism of silica capsules was proposed.