Ce1-xNixO2/Al2O3/FeCrAl催化剂的制备及其甲烷催化燃烧性能

以FeCrA l合金薄片为基体,A l2O3为过渡载体,Ce1-xN ixO2(x=0.1-0.3)、CeO2和N iO为活性组分,制备了Ce1-xN ixO2/A l2O3/FeCrA l、CeO2/A l2O3/FeCrA l和N iO/A l2O3/FeCrA l金属基整体式催化剂,在固定床微型反应器中评价了催化剂的甲烷催化燃烧性能,用SEM、XRD、TPR等方法对催化剂的物相、表面形貌和氧化还原性进行了表征.结果表明,Ce1-xN ixO2在催化剂表面的分散性比CeO2和N iO要好;Ce1-xN ixO2/A l2O3/FeCrA l(x=0.1-0.3)催化剂具有好的催化活性和高温稳定性,CeO2/A l2O3/FeCrA l和N iO/A l2O3/FeCrA l催化剂有好的初活性但高温稳定性较差;活性组分与A l2O3和FeCrA l金属基体之间存在较强的相互作用.     

La取代Ba对Ba1-xLaxMn3Al9O19-α催化剂结构及甲烷催化燃烧性能的影响

采用以尿素水解为基础的水热合成法制备了La和Mn取代的六铝酸盐催化剂(Ba1-xLaxMn3Al9O19-α).在Mn含量达到阈值时,研究了不同量的La取代Ba对Ba1-xLaxMn3Al9O19-α的相组成、结构、热稳定性及甲烷催化燃烧活性的影响.当x≥0.4时,水热合成过程中生成的La2(CO3)3在530-580℃分解,800-900℃时与-γAl2O3反应生成LaAlO3钙钛矿相,可抑制由BaCO3分解而生成的Ba2+的固相扩散,从而阻止了BaAl2O4尖晶石相的生成,使Ba2+在固相中保持较高的分散性,促进了六铝酸盐(-βAl2O3)相的形成.当x<0.4时,BaAl2O4尖晶石相的存在引起催化剂比表面积和催化燃烧活性的降低.La3+取代Ba2+后,六铝酸盐结构发生一定程度的扭变.这种扭变越大,所形成的六铝酸盐催化剂的热稳定性越差.Ba1-xLaxMn3Al9O19-α催化剂的甲烷催化燃烧活性随x的增大而增加,x=0.8时催化剂的活性最佳.     

Reforming of CH4 with CO2 over Co/Mγ-Al oxide catalyst

A series of Co/Mg–Al oxide samples,CoMgAl-x(x=(Mg+Co)/Al molar ratio of 1–5),were prepared by the self-combustion method followed by H2reduction.The catalytic performance and stability of the samples were studied in dry reforming of CH4.XRD and H2-TPR characterization results showed that the reduced CoMgAl-x samples mainly consisted of solid solution and spinel phases with cobalt particles.The spinel phases contained Co3O4 and Con Mg1-n Al2O4(0≦n≦1)varying with the(Mg+Co)/Al ratio.The effect of (Mg+Co)/Al molar ratio on the catalytic behavior was investigated in detail and CoMgAl-3 exhibited the highest catalytic activity and stability among the catalysts studied.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体,制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1,0.75,0.5,0.25,0).应用Brunauer-Emmet-Teller(BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征,并系统研究了催化剂在饮食油烟催化燃烧中的催化活性.BET结果表叫催化剂的比表面积随Ce/Zr摩尔比的减小而减小.XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上.H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好.催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧,降低了反应温度.随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化,催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2＞Pt/γ-Al2O3/Ce0.25Zr0.75O2＞Pt/γ-Al2O3/Ce0.75Zr0.25O2＞Pt/γ-Al2O3/CeO2＞Pt/γ-Al2O3/ZrO2.     

Ce0.5+xZr0.4-xLa0.1O2-Al2O3催化剂催化燃烧柴油车碳烟

采用共沉淀法制备了系列Ce_0.5+xZr_0.4-xLa_0.1O₂-Al₂O₃催化剂, 其中0≤x≤0.4且Ce_0.5+xZr_0.4-xLa_0.1O₂与Al₂O₃的质量比为1:1. 考察了该系列催化剂对柴油车排放碳烟的催化燃烧性能, 并用低温N2吸附-脱附、X射线衍射(XRD)、X射线光电子能谱(XPS)、氢气程序升温还原(H₂-TPR)和氧气程序升温脱附(O₂-TPD)等手段对催化剂进行了表征. 研究结果表明该系列催化剂均形成了具有立方萤石结构的固溶体. 当x=0.2时, Ce³⁺离子在催化剂表面有一定的富集, 此时催化剂具有最大的β氧脱附峰和最好的表面还原性能, 同时具有良好的催化碳烟氧化活性, 碳烟在该催化剂的起燃温度为360 °C, 具有较好的应用前景.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体, 制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1, 0.75, 0.5, 0.25, 0). 应用Brunauer-Emmet-Teller (BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征, 并系统研究了催化剂在饮食油烟催化燃烧中的催化活性. BET结果表明催化剂的比表面积随Ce/Zr摩尔比的减小而减小. XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上. H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好. 催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧, 降低了反应温度. 随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化, 催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2>Pt/γ-Al2O3/Ce0.25Zr0.75O2>Pt/γ-Al2O3/Ce0.75Zr0.25O2>Pt/γ-Al2O3/CeO2>Pt/γ-Al2O3/ZrO2.     

Catalytic Combustion of Methane over MnOx／ZrO2-Al2O3 Catalysts

MnOx/Al2O3 and MnOx/ZrO2-Al2O3 catalysts were prepared by incipient wetness impregnation of Mn(CH3COO)2 on the corresponding supports, followed by the characterization using X-ray diffraction (XRD). temperature programmed reduction (TPR) and BET surface area techniques. The result shows the BET surface area of ZrO2-Al2O3 is lower than that of Al2O3 due to the loading of ZrO2.However tile resulted MnOx/ZrO2-Al2O3 catalyst exhibits higher activity for methane combustion than MnOx/Al2O3, because the addition of ZrO2 onto Al2O3 is beneficial for the dispersion of Mn species and the improvement of the lattice oxygen activity in MnOx. subsequently the activation of methane during combustion. The optimum loading of Zr in MnOx/ZrO2-Al2O3 is in the range of 5%-10% correlated with the calcination temperatures of catalyst supports.     

Effect of Mg/Al atom ratio of support on catalytic performance of Co-Mo/MgO-Al2O3 catalyst for water gas shift reaction

Co-Mo-based catalysts supported on mixed oxide supports MgO-Al2O3 with different Mg/Al atom ratios for water gas shift reaction were studied by means of TPR, Raman, XPS and ESR. It was found that the octahedral Mo species in oxidized Co-Mo/MgO(x)-Al2O3 catalyst and the contents of Mo5+, Mo4+, S2- and S2-2 species in the functioning catalysts increased with increasing the Mg/Al atom ratio of the support under the studied experimental conditions. This is favorable for the formation of the active Co-Mo-S phase of the catalysts. Catalytic performance testing results showed that the catalysts Co-Mo/MgO-Al2O3 with the Mg/Al atom ratio of the support in the range of 0.475-0.525 exhibited optimal catalytic activity for the reaction.     

掺杂助剂Ce和Zr的Ni/Al2O3催化剂的X光电子能谱分析

以Na2CO3为沉淀剂,在pH 9.0的沉淀条件下,采用并流沉淀法制备了Ni/Al2O3、Ni/CeO2-Al2O3、Ni/ZrO2-Al2O3和Ni/ZrO2-CeO2-Al2O34种催化剂,催化剂中Ni负载量(质量分数)为10%。采用XPS表征手段及常压固定床反应器对催化剂进行活性评价,考察了助剂Ce和Zr及二者的协同作用对Ni基催化剂表面物种结合能的影响以及对甲烷自热重整制氢反应性能的影响。结果表明,助剂Ce和Zr的添加及二者的协同作用对Ni基催化剂表面各物种的结合能均有一定的影响,结合评价结果可知,Ce和Zr二者的协同作用对Ni基催化剂的催化性能提高最大。     

CuxCo1-x/Al2O3/堇青石整体式催化剂的制备及其催化甲苯燃烧性能

以堇青石蜂窝陶瓷为基底,A12O3浆料为过渡胶体,Cu和Co为催化活性组分,制备了一系列CuxCo1-x/Al2O3/堇青石(x=0～1)整体式催化剂.采用X射线衍射、X射线光电子能谱、扫描电镜和程序升温还原等手段对催化剂进行了表征.以甲苯为模型化合物.在微型固定床反应器上评价了催化剂的催化性能.结果表明,当Cu含量较...     

Effect of Transition Metals (Cu, Co and Fe) on the Autothermal Reforming of Methane over Ni/Ce0.2Zr0.1Al0.7Oδ Catalyst

The transition metals (Cu, Co, and Fe) were applied to modify Ni/Ce0.2Zr0.1Al0.7Oδ catalyst.The effects of transition metals on the catalytic properties of Ni/Ce0.2Zr0.1Al0.7Oδ autothermal reforming of methane were investigated. The Ni-supported catalysts were characterized by XRD, TPR and XPS.Tests in autothermal reforming of methane to hydrogen showed that the addition of transition metals (Cu and Co) significantly increased the activity of catalyst under the conditions of lower reaction temperature,and Ni/Cu0.05Ce0.2Zr0.1Al0.65Oδ was found to have the highest conversion of CH4 among all catalysts in the operation temperatures ranging from 923 K to 1023 K. TPR, XRD and XPS measurements indicated that the cubic phases of CexZr1-xO2 solid solution were formed in the preparation process of catalysts.Strong interaction was found to exist between NiO and CexZr1-xO2 solid solution. The addition of Cu improved the dispersion of NiO, inhibited the formation of NiAl2O4, and thus significantly promoted the activity of the catalyst Ni/Cu0.05Ce0.2Zr0.1Al0.65Oδ.     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

＂Intelligent＂ reforming catalysts： Trace noble metal-doped Ni/Mg（A1）O derived from hydrotalcites

Trace amounts of noble metal-doped Ni/Mg(Al)O catalysts were prepared starting from Mg-Al hydrotalcites (HTs) and tested in daily start-up and shut-down (DSS) operation of steam reforming (SR) of methane or partial oxidation (PO) of propane. Although Ni/Mg(Al)O catalysts prepared from Mg(Ni)-Al HT exhibited high and stable activity in stationary SR, PO and dry reforming of methane and propane, the Ni/Mg(Al)O catalysts were drastically deactivated due to Ni oxidation by steam as purge gas when they were applied in DSS SR ofmethane. Such deactivation was effectively suppressed by doping trace amounts of noble metal on the catalysts by using a “memory effect” of HTs. Moreover, the noble metal-doped Ni/Mg(Al)O catalysts exhibited “intelligent” catalytic behaviors, i.e., self-activation and self-regenerative activity, leading to high and sustainable activity during DSS operation. Pt was the most effective among noble metals tested. The self-activation occurred by the reduction of Ni2+ in Mg(Ni,Al)O periclase to Ni0 assisted by hydrogen spillover from Pt (or Pt-Ni alloy). The self-regenerative activity was accomplished by self-redispersion of active Ni0 particles due to a reversible reductionoxidation movement of Ni between the outside and the inside of the Mg(Al)O periclase crystal; surface Ni0 was oxidized to Ni2+ by steam and incorporated into Mg(Ni2+,Al)O periclase, whereas the Ni2+ in the periclase was reduced to Ni0 by the hydrogen spillover and appeared as the fine Ni0 particles on the catalyst surface. Further a “green” preparation of the Pt/Ni/[Mg3.5Al]O catalysts was accomplished starting from commercial Mg3.5-Al HT by calcination, followed by sequential impregnation of Ni and Pt.     

Additive effects of alkaline-earth metals and nickel on the performance of Co/γ-Al_2O_3 in methane catalytic partial oxidation

Nano-sized γ-alumina (γ-Al2O3) was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel (Ni) with different contents were loaded on the γ-Al2O3 support. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction (XRD) and thermogravimetry analysis (TGA). The activity and selectivity of the catalysts in catalytic partial oxidation (CPO) of methane have been compared with Co/γ-Al2O3, and it is found that the catalytic activity, selectivity, and stability are enhanced by the addition of alkaline-earth metals and nickel. The optimal loadings of strontium (Sr) and Ni were 6 and 4 wt%, respectively. This finding will be helpful in designing the trimetallic Co-Ni-Sr/γ-Al2O3 catalysts with high performance in CPO of methane.     

PROMOTING EFFECT OF RARE EARTH OXIDES ON Ni/Re_xO_y-Al_2O_3 CATALYST FOR PARTIAL OXIDATION OF METHANE TO SYNTHESIS GAS

IntroductionSynthesisgas(HZ CO)isproducedfrommethanemoshybysteamrefonningwhichsuffersfromlimitationssuchasveryhighenergyrequirements,complicatedequipmentandinstallations,highHZ/COproductratioandpoorselectivityforcarbonmonoxide.Recently,manyresearchershave…     

制备方法对 LaMn0.8Mg0.2O3 钙钛矿型氧化物催化甲烷燃烧反应性能的影响

 分别采用甘氨酸硝酸盐法、溶胶凝胶法、共沉淀法、燃烧法以及水热法制备了钙钛矿型 LaMn0.8Mg0.2O3 复合氧化物, 用 X 射线衍射、红外光谱、H2 程序升温还原和低温 N2 吸附对其进行了表征, 并考察了其对甲烷燃烧的催化活性. 结果表明, 制备方法和焙烧温度对 LaMn0.8Mg0.2O3 钙钛矿型催化剂的结构、晶粒大小和不同类型的氧物种影响很大. 以甘氨酸硝酸盐法制备的钙钛矿型催化剂经 700 °C 焙烧后表现出最高的催化活性, T50 (甲烷转化率达到 50% 时的温度) 仅为 440 °C. 这归结于它较小的晶粒尺寸 (12.4 nm) 和较大的比表面积 (18.6 m2/g), 以及催化剂表面富集的 Mn4+, 从而使表面氧物种更容易移动和/或更具有反应活性.     

Solution combustion synthesis of Co oxide-based catalysts for phenol degradation in aqueous solution

Solution combustion using urea as a fuel was employed to synthesise Co oxide and Al(2)O(3)-, SiO(2)- and TiO(2)-supported Co oxide catalysts. The catalysts were characterised using several techniques such as N(2) adsorption/desorption, XRD, FTIR, UV-vis diffuse reflectance and SEM-EDX, and their catalytic activity was evaluated in phenol degradation in aqueous solution with sulphate radicals. Solution combustion is a simple and effective method in preparation of supported Co catalysts. Co(3)O(4) was the major Co crystal phase in the samples prepared via the combustion synthesis. Bulk Co(3)O(4) particles were not effective in reaction, but supported Co oxides showed higher activity than unsupported Co oxide. The supports influenced Co dispersion and catalytic activity. Co/TiO(2) exhibited the highest activity, but it deactivated much faster than other two supported catalysts. Co/SiO(2) showed a comparable activity to Co/Al(2)O(3) and the best stability among the three Al(2)O(3)-, SiO(2)- and TiO(2)-supported Co catalysts.     

CO氧化反应中H2O对MOx和Au/MOx催化性能的影响

过渡金属氧化物［1,2］及负载型贵金属催化剂［3～13］是催化氧化消除CO的有效催化剂,一直是研究的热点. 虽然对MOx和Au/MOx上CO的氧化性能研究得较多,但大多是在无水条件下进行的;涉及催化剂抗水性能的报道较少［3,9,10］,且仅限于对催化剂活性的研究. Haruta等［3］对Au/Fe2O3,Au/Co3O4和Au/TiO 2等体系开展了一些工作, 认为水对CO氧化活性有促进作用. 本文重点考察了水对MOx(M=Al,Ca,Co,Cr,Cu,Fe,La,Mn,Ni和Zn)催化剂上CO氧化活性的影响,以及水对Au/MOx 催化剂活性及稳定性的影响.     

Methane Dry Reforming over Alumina Supported Co Catalysts

A series of Co/γ-Al2O3 catalysts were prepared with the impregnation .method and characterized by means of the BET specific surface area, X-ray diffraction (XRD), thermogravimetric analysis (TGA) and Laser Raman spectroscopy. The Co/γ-Al2O3 catalysts were activated by using H2, 20%CH4/H2 or CH4, re-spectively. There was no obvious difference between the activities of the Co/γ-Al2O3 catalyst activated by us-ing the different activation methods for methane dry reforming. The catalytic properties of the Co/γ-Al2O3 catalysts with different Co loadings were also investigated. The optimized Co loading for the Co/γ-Al2O3 cata-lyst pretreated with 20% CH4/H2 is around 12% (mass fraction).     

助剂对Cu-Mn复合氧化物整体式催化剂催化低浓度甲烷燃烧反应性能的影响

以堇青石蜂窝陶瓷(COR)为载体,采用浸渍法制备了Cu-Mn-O/A12O3/COR,Cu-Mn-Ce-O/Al2O3/COR,Cu-Mn-Zr-O/Al2O3/COR,Cu-Mn-La-O/A12O3/COR和Cu-Mn-Ce-Zr-O/Al2O3/COR5种Cu-Mn复合氧化物整体式催化剂,用于低浓度甲烷催化燃烧反...