表面活性剂对部分水解聚丙烯酰胺溶液抗盐性的影响

通过实验研究了阴离子表面活性剂(SDS)、非离子表面活性剂(OP-10)、两性表面活性剂(C12BE)浓度及KCl浓度对部分水解聚丙烯酰胺(阴离子型,HPAM)水溶液黏度的影响规律,进而分析各因素对聚合物溶液抗盐性的影响。实验结果表明:当表面活性剂浓度低于临界缔合浓度CAC时,聚合物溶液黏度变化不大;高于CAC后,随着表面活性剂浓度增大,聚合物溶液黏度急剧增加;当表面活性剂浓度达到聚合物饱和浓度PSP时,聚合物溶液黏度达到最大值;再加入阴离子和两性表面活性剂,将导致黏度降低,而加入非离子表面活性剂不再改变聚合物溶液的黏度,无机盐KCl对聚合物溶液有双重作用,低浓度KCl促进聚合物溶液黏度升高,高浓度KCl则导致聚合物溶液黏度急剧降低后趋于稳定,在相同KCl浓度下,三种表面活性剂的抗盐能力表现为:SDSOP-10C12BE。     

烷基糖苷-十二烷基甜菜碱复配性能及无机盐的影响

考察了非离子型表面活性剂烷基糖苷(APG)和两性表面活性剂十二烷基甜菜碱(BS-12)之间的复配性能,测定了不同摩尔比的APG和BS-12复配体系的表面张力、泡沫和乳化性能,并且研究了无机盐对复配体系表面活性的影响。结果表明,与单独任一表面活性剂体系相比,APG和BS-12复配体系具有较好的表面活性,呈现明显的协同增效作用;在摩尔比为3∶7时,复配体系的表面活性最高、起泡性能最好、形成的泡沫和乳状液最稳定,协同增效作用最显著。此外,无机盐的加入提高了复配体系的表面活性,当NaCl浓度为0.03mol/L时,表面张力和临界胶束浓度最小,表面活性最高;而对于无机盐,其离子价态越高,提高表面活性程度越明显;相比之下,阳离子提高复配体系表面活性的能力大于阴离子。     

评价表面活性剂溶液泡沫性能的方法—真球气泡法北大核心CSCD

通过真球气泡法测定了不同价数和浓度的无机盐体系下十二烷基硫酸钠(SDS)表面活性剂溶液的表面张力和表面扩展黏度;通过Ross-Miles法测定了相应同一溶液的发泡力和泡沫稳定性;结果表明:SDS溶液的表面张力值随着各种无机盐浓度的增加而减小至不变,此时的无机盐浓度作为相对浓度100%来考察时,发现临界胶束浓度(CMC)值与添加盐的种类无关,只随无机盐的相对浓度的增加而减少;即CMC值随着无机盐的相对浓度的增加从不含无机盐时的8.3 mmol/L均收敛至最小值3.0 mmol/L;表面张力值和对应的发泡力值呈负线性关系,由此推断表面张力值可以评价发泡力;表面扩展黏度值和对应的泡沫稳定性值呈正线性关系,由此推断表面扩展黏度可以评价泡沫稳定性;无机盐种类对SDS表面活性剂发泡力和泡沫稳定性的影响力随阳离子价数(Na^(+)、Cu^(2+)、Fe^(3+))增加而增加。     

电解质和乙醇对DNA与Gemini表面活性剂相互作用的影响

应用荧光探针和zeta电位方法研究了电解质NaBr、NaCl、KCl和有机溶剂乙醇对DNA与Gemini表面活性剂相互作用的影响. DNA诱导的表面活性剂类胶束在较低浓度即可生成, 这一浓度称为临界聚集浓度(CAC). Gemini表面活性剂比具有相同烷烃链长的单体表面活性剂更易聚集, 对应的CAC较低. 实验结果表明, 盐(NaBr)浓度对DNA/表面活性剂体系的CAC影响不大, 阴、阳离子的种类则对该体系有不同程度的影响. 阴离子(Br-、Cl-)对体系的CAC有显著的影响, 但阳离子(Na+、K+)的差异对CAC影响不大. 极性溶剂乙醇对DNA与表面活性剂相互作用的影响比较复杂. 乙醇浓度较低时有利于表面活性剂的聚集, 使得CAC减小; 而浓度较高时, 则不利于表面活性剂聚集,从而使CAC变大. 乙醇可显著改变DNA/表面活性剂复合物的zeta电位.     

烷基糖苷-十二烷基甜菜碱复配性能及无机盐的影响

本文考察了非离子型表面活性剂烷基糖苷（APG）和两性表面活性剂十二烷基甜菜碱（BS-12）之间的复配性能,测定了不同摩尔比的APG和BS-12复配体系的表面张力、泡沫和乳化性能,并且研究了无机盐对复配体系表面活性的影响情况。研究结果表明,APG和BS-12复配体系与单独任一表面活性剂体系相比具有较好的表面活性,两者具有明显的协同增效作用,且在摩尔比为3:7时,复配体系的表面活性最高、起泡性能最好、形成的泡沫和乳状液最稳定,协同增效作用最显著。此外,无机盐的加入提高了复配体系的表面活性,当NaCl浓度为0.0     

疏水缔合聚丙烯酰胺与双子表面活性剂的自组装

通过荧光光谱、动/静态激光光散射研究了疏水缔合聚丙烯酰胺(HAPAM)自组装行为及双子表面活性剂(双十四酸乙二酯双磺酸盐(DMES-14))对其的影响.实验结果表明:聚合物HAPAM在溶液中能够通过自组装形成疏水微区,表现出芘的发射光谱中第一振动峰(373nm)与第三振动峰(383nm)的荧光强度之比(I1/I3)值随聚合物浓度的增大而下降,当聚合物HAPAM浓度(CP)达到一定值后,I1/I3值不再变化;当加入表面活性剂时,HAPAM能够与双子表面活性剂在溶液中形成混合胶束,在聚合物浓度一定时,I1/I3值随表面活性剂浓度(CS)的增大急速下降,当表面活性剂浓度达到30mg·L-1时,I1/I3值趋于恒定;当表面活性剂浓度一定时,聚合物/表面活性剂二元体系中聚集体的聚集数随HAPAM浓度的增大出现先下降再增加的过程;一定量的双子表面活性剂对HAPAM分子间的缔合起促进作用,过量的双子表面活性剂对HAPAM分子间的缔合起抑制作用,使HAPAM的表观重均分子量(Mw,a)、均方根回转半径()和流体力学半径()随表面活性剂浓度增加先增大后减小,而HAPAM的/比值则随表面活性剂浓度增大出现一定程度的上升,表明HAPAM分子链段变得相对舒展.     

表面活性剂对海藻酸钠稀水溶液剪切粘度的影响

通过粘度法考察了不同pH值时, 阴离子聚电解质海藻酸钠(NaAlg)与阴离子表面活性剂十二烷基硫酸钠(SDS)、阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)、非离子表面活性剂辛基酚聚氧乙烯醚(TritonX-100)以及它们的复配体系的相互作用. 研究表明, 在酸性条件下, SDS和TritonX-100与NaAlg之间主要是疏水作用, 随着表面活性剂浓度的增加, 体系粘度下降直到基本不变, CTAB与NaAlg主要发生静电作用和疏水作用, 体系粘度随CTAB浓度的增加呈现先上升后下降的趋势. 在实验条件下, TritonX-100浓度为0.05 mmol·L-1时, SDS的加入, 使得NaAlg/TritonX-100体系的零剪切粘度下降, 而CTAB的加入, 在pH=3.0和5.0时, NaAlg/TritonX-100体系的零剪切粘度出现上升, 在pH=6.4时, 该体系零剪切粘度下降.     

无机盐对辛基酚聚氧乙烯醚乙基磺酸钠临界胶束浓度的影响研究

在(25±0.2)℃的实验温度下,通过用表面张力法确定了辛基酚聚氧乙烯醚(10)乙基磺酸钠(OPS)在无机盐氯化物(LiCl,NaCl,KCl,MgCl2,CaCl2,BaCl2,AlCl3,FeCl3和SmCl3)水溶液中的临界胶束浓度(cmc)值,根据cmc值的变化得出无机盐反离子对非离子-阴离子型表面活性剂OPS的cmc值影响规律.实验数据分析表明,虽然非离子-阴离子型表面活性剂OPS分子中增加了一个非离子氧乙烯单元的亲水性基团,但其cmc值和无机盐反离子浓度[M]之间具有与离子型表面活性剂相似的线性关系:lgcmc=-4.242-(0.2980-0.0102Z/r)lg[M]([M]1mol/L),其中Z和r分别为反离子的价态和范德华原子半径的平均值.无机盐对OPS的cmc的影响具有离子型表面活性剂的性质,不具有非离子型或两性表面活性剂的性质.该关系式亦说明了水溶液中非离子-阴离子型表面活性剂OPS的cmc值与无机盐反离子的浓度、价态和范德华原子半径的平均值有关,反离子对胶束的结合度的大小取决于反离子的价态与范德华原子半径平均值的比值.最后就无机盐反离子对OPS的cmc影响机理进行了简要分析.     

新型磺基甜菜碱/聚丙烯酰胺体系表面及界面性能

采用自制的新型磺基甜菜碱两性表面活性剂与相对分子质量2500万的聚丙烯酰胺进行复配,考察了不同温度和矿化度条件下,聚合物对复配溶液表面、界面性能的影响。 采用滴体积法测定了溶液的表面张力,结果表明,加入聚合物使溶液的临界胶束浓度增大,且复配溶液的表面张力大于单独表面活性剂溶液的表面张力。 当聚合物浓度一定,增大溶液矿化度时,体系表面张力增大。 用旋滴型界面张力仪测定了溶液的界面张力,结果表明,增大聚合物浓度,油水界面张力增大,增大溶液矿化度,油水界面张力有所升高。 聚合物质量浓度为1.5 g/L,表面活性剂质量浓度为0.3 g/L时,可使胜利油田孤岛原油和孤东原油的油水界面张力达到超低数量级（10-3 mN/m）。 用分水时间法测定了溶液的乳化性能,结果表明,聚合物浓度增大,分水时间延长,并考察了75、85和95 ℃条件下体系的乳化性能,温度越高,分水时间越短。     

醇-可聚合表面活性剂混合胶束法合成微嵌段缔合聚合物及其流变性

低碳醇与可聚合表面活性剂(surfmer)可以形成混合胶束, 本文通过稳态荧光猝灭法(SSFQ)测定了该混合胶束中可聚合表面活性剂的聚集数, 并通过绝热聚合和后水解工艺合成出不同微嵌段长度的较高分子量(M_w)缔合聚合物聚(丙烯酰胺-丙烯酸钠-十六烷基二甲基烯丙基氯化铵)[P(AM-NaAA-C₁₆DMAAC)]. 聚合物结构经傅里叶变换-红外(FT-IR)光谱和核磁共振碳谱(¹³C NMR)表征证实, 并通过流变性实验研究了微嵌段长度对增粘性能、抗盐性能、粘弹性能的影响规律. 实验结果表明: 该方法可以有效调节缔合聚合物中微嵌段的长度, 随着微嵌段长度增加, 临界缔合浓度(CAC)逐渐降低, 增粘性能、粘弹性能先逐步增加后逐步降低, 并且发现其对聚合物的性能的影响规律中存在最佳嵌段长度.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.