两性表面活性剂与阴离子聚丙烯酰胺复配体系的抗盐性

通过单因素实验分析两性表面活性剂浓度、无机盐浓度及pH值对聚丙烯酰胺复配体系黏度的影响规律,应用SPSS软件对均匀实验结果进行非线性回归,得到复配体系黏度与聚合物浓度、两性表面活性剂浓度及无机盐浓度的定量关系式,进而理论分析了各因素对复配体系抗盐性的影响规律.结果表明,当两性表面活性剂的浓度低于临界缔合浓度(CAC)时,复配体系的黏度变化不大;当其浓度高于CAC后,随着浓度的增加,体系黏度急剧增大;当其浓度达到聚合物饱和浓度(PSP),复配体系黏度达到最大值;当再进一步加入表面活性剂时,聚集体间的网状结构将被破坏,从而使体系黏度逐渐降低;无机盐对复配体系的作用具有双重性,低浓度盐将促使体系黏度升高,中高浓度盐则会导致体系黏度降低;不同pH值条件下,复配体系的抗盐能力顺序为碱性(pH=11.4)＞酸性(pH=2.8)＞中性(pH=7).     

两亲无规聚合物的聚集行为及其与非离子表面活性剂的相互作用

以2-丙烯酰胺基-十二烷基磺酸(AMC12S)与2-丙烯酰胺基-2-甲基丙磺酸(AMPS)进行无规共聚,合成了含AMC12S摩尔分数(X)较高(X=0.1,0.3,0.5)的一系列两亲聚合物.采用稳态荧光及动态光散射技术对聚合物在水溶液中的聚集行为及其与三种非离子表面活性剂(HO(CH2CH2O)10C12H25(C12E10)、HO(CH2CH2O)20C12H25(C12E20)和HO(CH2CH2O)40C12H25(C12E40))的相互作用进行了研究,并考察了X对聚集行为的影响以及表面活性剂亲水基团长度对相互作用的影响.随着X的增大,聚合物的临界聚集浓度(CAC)明显减小,X=0.5时聚合物的CAC低达0.0039g·L-1.聚集体的流体力学半径(Rh)都大于26nm,并随着聚合物浓度的升高而增大,说明聚合物分子主要以分子间的聚集方式聚集,形成多分子聚集体.随X的增大,聚集体Rh减小,同时Rh随聚合物浓度升高而增大的幅度减小,说明聚集体结构变得更加紧实.表面活性剂与聚合物之间存在很强的相互作用,在混合溶液中表面活性剂浓度达到临界胶束浓度(CMC)左右时聚合物聚集体开始解离,形成混合聚集体.亲水基团长度增长,表面活性剂对聚合物聚集体的解离能力随之增强.C12E40与X=0.5的聚合物形成的混合聚集体Rh为6.8nm,与C12E40自身形成的聚集体尺寸相当.     

电解质和乙醇对DNA与Gemini表面活性剂相互作用的影响

应用荧光探针和zeta电位方法研究了电解质NaBr、NaCl、KCl和有机溶剂乙醇对DNA与Gemini表面活性剂相互作用的影响. DNA诱导的表面活性剂类胶束在较低浓度即可生成, 这一浓度称为临界聚集浓度(CAC). Gemini表面活性剂比具有相同烷烃链长的单体表面活性剂更易聚集, 对应的CAC较低. 实验结果表明, 盐(NaBr)浓度对DNA/表面活性剂体系的CAC影响不大, 阴、阳离子的种类则对该体系有不同程度的影响. 阴离子(Br-、Cl-)对体系的CAC有显著的影响, 但阳离子(Na+、K+)的差异对CAC影响不大. 极性溶剂乙醇对DNA与表面活性剂相互作用的影响比较复杂. 乙醇浓度较低时有利于表面活性剂的聚集, 使得CAC减小; 而浓度较高时, 则不利于表面活性剂聚集,从而使CAC变大. 乙醇可显著改变DNA/表面活性剂复合物的zeta电位.     

TBAB/KCl对构筑阴离子蠕虫状胶束的影响

采用流变测试技术考察了两种阴离子表面活性剂油酸钠(NaOA)和芥酸钠(NaOEr)在四丁基溴化铵(TBAB)和KCl诱导下构筑蠕虫状胶束的行为.随着KCl浓度增加, NaOA水溶液粘度增加,而加入TBAB使NaOA-KCl样品的粘度持续降低.与之相反, TBAB浓度的增加却使NaOEr-KCl样品的粘度大幅度增强.此外, NaOEr分子比NaOA表现出更强的形成胶束的能力,构成粘弹性蠕虫状胶束所需表面活性剂浓度和盐浓度更少.本文采用TBAB和KCl两种盐协同诱导NaOEr,制备了具有强粘弹性的阴离子蠕虫状胶束,探讨了盐TBAB/KCl对长链阴离子表面活性剂构筑蠕虫状胶束的影响机理.     

类水滑石诱导囊泡的自发形成

报道了一种新的囊泡合成方法——荷电固体纳米颗粒诱导囊泡的自发形成. 研究发现, 将5.0 g/L带结构正电荷的Mg₃Al类水滑石(HTlc)溶胶和0.02 mol/L由两性表面活性剂十二烷基甜菜碱(C₁₂BE)和阴离子表面活性剂双(2-乙基己基)琥珀酸磺酸钠(AOT)组成的溶液(C₁₂BE与AOT物质的量比为3∶2)混合, 当HTlc溶胶与表面活性剂溶液的体积比在1∶9～4∶6范围内, 在HTlc纳米颗粒的诱导下可自发形成囊泡, 并获得稳定的HTlc-囊泡复合分散体系.     

C12-s-C12·2Br和C12En混合水溶液的胶团化行为

季铵盐二聚表面活性剂C12-s-C12@2Br(s=2、3、4、6)和非离子表面活性剂C12E10或C12E23在水溶液中生成混合胶团.其临界胶团总浓度cmcT值介于二元复配体系中各组分的临界胶团浓度和之间.当添加少量非离子型表面活性剂(在水溶液中的摩尔分数α2=0.1)时,混合胶团中C12E10或C12E23的摩尔分数均已超过0.35;随着溶液中非离子型表面活性剂含量的增大,混合胶团中逐渐以C12E10或C12E23成分为主.     

C_(12)-s-C_(12)·2Br和C_(12)E_n混合水溶液的胶团化行为

季铵盐二聚表面活性剂C12-s-C12·2Br(s=2、3、4、6)和非离子表面活性剂C12E10或C12E23在水溶液中生成混合胶团.其临界胶团总浓度cmcT值介于二元复配体系中各组分的临界胶团浓度cmc01和cmc02之间.当添加少量非离子型表面活性剂(在水溶液中的摩尔分数α2=0.1)时,混合胶团中C12E10或C12E23的摩尔分数均已超过0.35;随着溶液中非离子型表面活性剂含量的增大,混合胶团中逐渐以C12E10或C12E23成分为主.     

正负离子表面活性剂与两性表面活性剂的相互作用

本文研究正负离子表面活性剂与两性表面活性剂混合水溶液的表面性质, 以及两性表面活性剂对正负离子裘面活性剂溶解度的影响。结果表明: (1) 两性表面活性剂的加溶作用,有助于正负离子表面活性剂的溶解; (2) 加入两性表面活性剂的量适当, 混合溶液基本保持原正负离子表面活性剂的表面活性; (3) 正负离子表面活性剂与两性表面活性剂在表面层和胶团中分子间的相互作用比正负离子表面活性剂与非离子表面活性剂分子间的相互作用稍强HC-FC正负; 离子表面活性剂与两性表面活性剂混合体系在表面层中有可能形成双分子或多分子层结构。     

十二烷基甜菜碱/十二烷基硫酸钠复配体系的表面活性

研究了两性表面活性剂十二烷基甜菜碱（C12BE）和阴离子型表面活性剂十二烷基硫酸钠（SDS）复配体系的形成胶束能力,降低表面张力效率,降低表面张力能力三种增效作用.发现C12BE和SDS摩尔比为6 :4时增效作用最显著.并考察了盐、醇对复配体系表面活性的影响,结果表明,加盐能导致表面活性的提高,加醇的机理比较复杂,乙醇对复配体系表面活性影响不大,而正丁醇影响则比较显著.     

表面活性剂对共轭聚合物荧光性质及电荷转移的影响

探讨了表面活性剂存在下, 水溶性阴离子共轭聚合物聚[5-甲氧基-2-(3-磺酰化丙氧基)-1,4-苯撑乙烯](简写为MPS-PPV)的微环境变化对荧光性质及电荷转移的影响. 结果表明, 阳离子表面活性剂及非离子表面活性剂使MPS-PPV荧光增强, 阴离子表面活性剂使其荧光先增强后减弱; 在MPS-PPV/表面活性剂体系中加入电子接受体Pd^2＋, 发现非离子表面活性剂体系的荧光猝灭效率提高, 阴离子及阳离子表面活性剂体系荧光猝灭效率下降. 此研究对研制基于阴离子共聚物的新型生物化学传感器具有一定的指导意义.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.