双单体固相共聚改性聚丙烯技术及其机理研究

在马来酸酐(MAH)固相接枝改性聚丙烯(PP)的过程中加入合适比例的异氰脲酸三烯丙酯(TAIC)作为共聚单体,可以大大提高MAH在PP上的接枝率,同时可以有效抑制在普通固相接枝过程中PP的严重降解,得到了性能较好的高极性PP.与普通固相接枝法与熔体接枝法对比,双单体固相共聚接枝改性PP是一种得到高极性PP的有效方法.本文同时对双单体在固相接枝反应中的作用机理进行了探讨.     

在超临界CO_2中进行的PP固相接枝改性研究进展

由于性价比高,聚丙烯(PP)成为增长最快的通用塑料,在汽车工业、家用电器和管材方面得到了广泛地应用。然而由于聚丙烯自身的非极性限制了其在某些领域的应用,向聚丙烯主链上接枝极性单体是改善其极性的有效方法。常用的接枝改性方法有:溶液接枝、熔融接枝、等离子体处理、表面可控活性聚合以及超临界CO2状态下接枝等。其中超临界CO2由于溶解单体能力强,对聚合物基体也有很好的溶胀能力,且阻燃性好、无毒以及价格相对低廉,克服了传统接枝方法存在的操作工艺复杂,溶剂不易回收等缺点,得到了广泛研究。本文从超临界CO2协助固相接枝改性机理、接枝单体的选择、影响过程的因素以及超临界CO2协助固相接枝的应用等方面出发,系统阐述了超临界CO2协助PP固相接枝改性近些年来的研究概况。     

不同改性剂对聚丙烯/碳酸钙复合材料性能的影响

以马来酸酐(MAH)、聚丙烯蜡(PPW)为主要原料,采用原位固相接枝改性法制得PP/CaCO3-MAH-PPW复合材料,并与添加相容剂聚丙烯接枝马来酸酐(PP-g-MAH)所制得的PP/PP-g-MAH/CaCO3复合材料进行比较。结果表明,CaCO3良好的分散性及其与PP基体适宜的界面粘接是复合材料具有较好韧性的关键因素。与PP/PP-g-MAH/CaCO3复合材料相比,PP/CaCO3-MAH-PPW复合材料表现出更佳的冲击、弯曲和加工性能,当m(PP)∶m(CaCO3)=100∶20时,材料缺口冲击强度达到最大值,是基体树脂的1.19倍。     

磨盘碾磨聚丙烯粒度分布与接枝率的研究

用分形几何方法研究了磨盘碾磨中聚丙烯 (PP)的粉碎和固相力化学接枝 .用粒度分析仪测定经磨盘碾磨聚丙烯的粒度分布 ,用分形理论处理实验数据 .结果表明 ,PP粒度分布存在无标度区 ,具有线性分形特征 ,磨盘碾磨对PP粒子分形行为有较大影响 ,聚丙烯粒度分布的分维值随碾磨次数的增加而增大 .磨盘碾磨中聚丙烯固相力化学接枝的实验结果表明 ,N 羟甲基丙烯酰胺在聚丙烯表面上的接枝率亦随碾磨次数增加而增加 ,即与聚丙烯粒度分布的分维值相关 .因此 ,可用分数维定量描述聚丙烯粒子在磨盘碾磨中的粉碎规律 ,揭示了N 羟甲基丙烯酰胺在聚丙烯表面固相力化学接枝反应的本质 .     

固相共聚接枝合成功能化聚丙烯及机理研究

通过马来酸酐 (MAH)和乙酸乙烯酯 (VAc)固相共聚接枝聚丙烯 (PP) ,在二者的投料摩尔比接近 1:1时 ,得到了高接枝率的多官能团功能化的PP .反应的机理是两单体摩尔比接近 1:1时容易形成较为稳定的过渡态 ,从而两者的共聚活性大大增加 ,接枝率大大提高 ,同时抑制了接枝产品熔体流动指数的增加 .这种含有多种官能团 (酸酐官能团和酯基官能团 )的极性PP对于拓展PP的应用范围 ,促进PP本身及其共混合金材料的功能化和高性能化有着重要的意义     

马来酸酐接枝聚丙烯的改性方法及其应用

马来酸酐(MAH)是聚丙烯改性中最常用的极性单体,在连续反应中酸酐基呈现很高的活性,反应产物热稳定性良好,可被应用于合金,塑料等材料的生产。随着各种技术的广泛应用,马来酸酐接枝聚丙烯改性方法得到了快速的发展。各种马来酸酐接枝聚丙烯的改性方法有:溶液接枝法、熔融接枝法、固相接枝法和辐射接枝法。文章阐述了马来酸酐接枝聚丙烯改性方法的研究现状及其产物在不同领域的应用。     

球形聚丙烯粒子固相接枝苯乙烯的研究

用负载型高效球形催化剂催化丙烯本体聚合获得了孔隙率较高的球形聚丙烯 (PP)粒子 .研究了苯乙烯在这种球形多孔PP粒子中的接枝聚合反应 ,考察了各种聚合条件对接枝率及接枝效率的影响 ,并用FTIR、DSC、GPC、粘度测定及偏光显微镜 (PLM)等方法表征了接枝聚合产物的结构和形态 .研究表明 ,球形PP粒子固相接枝苯乙烯不仅可达较高接枝率 (最高达 2 4 % )和接枝效率 (最高达 5 6 7% ) ,PS相区尺寸小、分布均匀 ,而且产物为形态规则的球形颗粒 ,有利于防止聚合物结块和粘壁 .但PP接枝PS后分子量有所下降 ,表明PP接枝PS的同时伴随着轻微的降解     

PP熔融接枝改性研究进展

聚丙烯作为一种非极性聚合物,其亲水性、染色性、粘结性及与其它极性聚合物和无机填料的相容性都很差,这大大限制了它的应用。因此,往往采用官能化的方法赋予聚丙烯以极性、反应活性和功能性。通过熔融接枝的方法,在聚丙烯链段上接枝极性单体,可以显著提高聚丙烯的极性,改善表面亲水性及染色性等。本文简要介绍了聚丙烯熔融接枝改性及其影响因素,并按接枝单体分类,综述了熔融接枝聚丙烯的研究进展、性能与应用,展望了其发展趋势。     

聚丙烯与马来酸酐在超临界CO2中的接枝聚合

聚丙烯(PP)以其强度高、耐热性好、密度小、易加工和价廉等特点成为重要的通用塑料。但由于非极性的分子结构,其亲水性、染色性、抗静电性、粘接性和印刷性并不理想,难以与极性聚合物和填料共混、复合。PP通过接枝引入极性基团是最常用的化学改性方法。常用的接枝单体有马来     

原位固相接枝改性碳酸钙/聚丙烯复合材料的制备

用马来酸酐（MAH）在碳酸钙（CaCO3）表面引入双键,通过原位固相接枝法将聚丙烯蜡（PPW）化学键合在CaCO3表面,制得3种接枝率的CaCO3-MAH-PPW。 将这3种改性CaCO3填充聚丙烯（PP）制备复合材料,研究了PP/CaCO3界面作用对复合材料强度的影响。 结果表明,CaCO3表面经PPW接枝改性后在PP中的分散性提高,与PP相容性变好;随着改性CaCO3表面PPW接枝率的提高,CaCO3与PP之间界面作用逐渐增强。 当PPW接枝率为4.48 mg PPW/g CaCO3时,CaCO3与PP之间的界面作用最强,复合材料拉伸强度下降最小,杨氏模量提升最大,当m(PP)∶m(CaCO3)=100∶50时,杨氏模量达0.86 GPa,是纯PP的1.63倍;而PPW化学接枝率为2.49 mg PPW/g CaCO3时,CaCO3与PP之间的界面作用适中,复合材料缺口冲击强度提升最大,且当m(PP)∶m(CaCO3)=100∶10时,缺口冲击强度达3.91 kJ/m2,是纯PP的1.35倍。     

PEROXIDE GRAFTING OF POWDERED POLYPROPYLENE BY BUTYL ACRYLATE

The efficiency of the grafting of powdered polypropylene (PP) by butyl acrylate (BA) initiated by tert.-butylperoxy-2-ethylhex-as a ratio of the grafted and polymerized monomer was relatively high during the whole course of the reaction and it does not decrease under 0.5. The relatively high polymerization rate and also grafting efficiency at the beginning of the reaction is refered to the gel effect - the monomer is absorbed in the amorphous part of the powdered PP. With increasing the content of monomer in the reaction feed, the content of unsoluble cross-linked polymer increased as the consequence of the radical cross-linking of polybutylacrylate chains. The mechanism of grafting of powdered PP by BA is discussed.     

Reactive processing of polymers: Effect of bifunctional and tri-functional comonomers on melt grafting of glycidyl methacrylate onto polypropylene

Two reactive comonomers, divinyl benzene (DVB) and trimethylolpropane triacrylate (TRIS), were evaluated for their role in effecting the melt free radical grafting reaction of the monomer glycidyl methacrylate (GMA) onto polypropylene (PP). The characteristics of the GMA-grafting systems in the presence and absence of DVB or TRIS were examined and compared in terms of the yield of the grafting reaction and the extent of the main side reactions, namely homopolymerisation of GMA (poly-GMA) and polymer degradation, using different chemical compositions of the reactive systems and processing conditions. In the absence of the comonomers, i.e. in a conventional system, high initiator concentrations of peroxides were typically required to achieve the highest possible GMA grafting levels which were found to be generally low. Concomitantly, both poly-GMA and degradation of the polymer by chain scission takes place with increasing initiator amounts. On the other hand, the presence of a small amount of the comonomers, DVB or Tris, in the GMA-grafting system, was shown to bring about a significant increase in the grafting level paralleled by a large reduction in poly-GMA and PP degradation. In the presence of these highly reactive comonomers, the optimum grafting system requires a much lower concentration of the peroxide initiator and, consequently, would lead to the much lower degree of polymer degradation observed in these systems. The differences in the effects of the presence of DVB and that of TRIS in the grafting systems on the rate of the GMA-grafting and homopolymerisation reactions, and the extent of PP degradation (through melt flow changes), were compared and contrasted with a conventional GMA-grafting system.     

接枝共聚的接枝参数表述方法的探讨

介绍了接枝共聚物接枝参数，如单体转化率、接枝率、接枝效率、均聚物含量及接枝频率，概述了对这些参数在进行表述淀粉接枝共聚时出现的种各种表达形式。在此基础上，指出了这些其在表达上出现的混乱现象。     

Model for Kinetics of Vinyl Chloride Polymerization

This paper gives a critical review of recent models for the polymerization of vinyl chloride. In solution and bulk polymerization the effect of eventual degradative chain transfer to monomer, addition of chain transfer agents, and precipitation of polymer is discussed. A model for emulsion polymerization is described which includes particle formation and kinetics of polymerization where especially desorption and reabsorption of radicals in the particles are included.     

等离子体引发聚合

叙述了近下赤等离子体引发聚合反应的研究情况及其在表面改性与合成新型高分子材料等方面的应用。     

Modifications of carbon nanotubes with polymers

The chemical functionalizations of carbon nanotubes (CNTs) could enhance their chemical compatibility and dissolution properties, which enable both a more extensive characterization and subsequent chemical reactivity. The modifications with polymers could not only improve CNTs’ solubility and dispersibility but also the interfacial interaction to polymeric matrices in its composites. The main methods for the modification of CNTs with polymers are noncovalent attachment (polymer wrapping and absorption) and covalent attachment (“grafting to”and “grafting from”). The current states of the literatures in the field are presented in this review.     

甲基丙烯酸甲酯/苯乙烯在硅片表面的RAFT接枝聚合

将3-(2-二硫代苯甲酸基丙酰氧基)丙基二甲基甲氧基硅烷化学键合于硅片表面.以甲基丙烯酸甲酯和苯乙烯为单体,在硅片表面进行可逆加成-断裂链转移(RAFT)接枝聚合.X-射线光电子能谱仪证实聚甲基丙烯酸甲酯(PMMA)、聚苯乙烯(PS)、苯乙烯/甲基丙烯酸甲酯的共聚物(poly(MMA-co-St))都接枝到硅片表面.但3个体系表现出不同的性质,甲基丙烯酸甲酯的RAFT聚合可控性差,分子量比设计分子量大得多,分子量分布指数宽,接枝密度仅为0·03chains/nm2;苯乙烯均聚合的活性/可控性好、分子量分布窄,接枝密度提高到0·21chains/nm2;共聚合体系综合了两个均聚体系的优点,分子量分布较窄,接枝密度最高为0·31chains/nm2,聚合物膜厚随转化率、数均分子量基本呈线性增长.     

Use of reactive polyetherimide to modify epoxy thermosets. I. Synthesis of an amino-grafted polyetherimide

The use of a nonreactive thermoplastic (TP) that is initially miscible and which phase separates during reaction has often been used to improve the toughness of epoxy networks. Most of the time no real improvement in fracture properties is obtained due to poor adhesion between phases. In this work the grafting of amino groups on the backbone of a polyetherimide (PEI) is studied. In order to avoid too high a degree of grafting and crosslinking of PEI, a synthesis in a dispersed medium is considered. Three amines are used: ethylene diamine (EDA), 1-2 aminoethyl-piperazine (AEP) and n-butylamine. The grafting reaction was characterized by FTIR, SEC and NMR. The influence of the drying and washing processes of the powder is shown. The degree of grafting is determined using both titration and nitrogen microanalysis and is in the range 1-5%. The glass transition temperatures of the amino grafted PEI decrease, almost linearly with the degree of grafting.     

POSTGRAFTING OF HYPERBRANCHED DENDRITIC POLYMER FROM TERMINAL AMINO GROUPS OF POLYMER CHAINS GRAFTED ONTO SILICA SURFACE

This paper describes postgrafting of hyperbranched dendritic polyamidoamine initiated from terminal amino groups of polymer chains grafted onto ultrafine silica surface in order to modify the silica surface. Surface grafting of polymer having terminal amino groups as initiator sites was performed by a reaction of terminal diamine-type polyoxyethylene with epoxy groups previously introduced onto the surface by 3-glycidoxypropyltri-methoxysilane treatment. The postgrafting reaction of dendritic polyamidoamine from the terminal amino groups was achieved by repeating the Michael addition of methyl acrylate to amino groups followed by amidation of the resulting ester moieties with ethylenediamine or hexamethylenediamine. Both the amount of amino groups and the percentage of postgrafting of the resulting polyamidoamine increased with an increase in the number of generations: the amino group content increased from 0.40 mmol/g to 2.68 mmol/g, and the percentage of postgrafting reached 61.0% after the 12th generation by using ethylenediamine in amidation. These values, however, were considerably smaller than the theoretical values. This indicates that the postgrafted polyamidoamine was a hyperbranched polymer but not a precise dendrimer. Ethylenediamine as a reactant in amidation was more effective than hexamethylenediamine, and a low content of initial amino groups was also preferred to a large amount of them probably because of steric hindrance in the propagation of hyperbranched dendritic polyamidoamine. The average particle size of hyperbranched dendritic polyamido-amine-postgrafted silica measured by light scattering photometry increased with an increase in the number of generations of the resulting polyamidoamine.     

GRAFTING OF ETHYLENE GLYCOL DIMETHACRYLATE ONTO SILK IN AQUEOUS ALCOHOLIC SOLUTION

The grafting of ethylene glycol dimethacrylate (EGDMA) onto silk in aqueous alcohol systems using potassiumpersulfate (KPS) in the presence of air was investigated. Effects of grafting conditions, such as concentrations of monomer,initiator and formic acid, temperature and time, on the graft yield were determined. The optimum graft conditions were foundto be: T = 80℃, t = 30 min, [KPS] = 1.85% [on the weight ofmonomer (owm)]; [formic acid] = 0.2% (V/V); [EGDMA] =80% [on the weight of fiber (owf)]. The activation energy of grafting at 50-80℃ was found to be 71.31 kJ/mol for EGDMA.Grafting equations were also evaluated. The graft yield value can be regulated by the concentration of monomer. The graftcopolymerization of EGDMA onto silk is effective in improving the crease-proofing of silk fabrics.