稳定图的测定与矩形离子阱质谱性能分析

从理论上讲, 离子阱质谱仪的性能是由阱内电场分布决定的,而电场分布又是由组成离子阱的电极几何结构和离子阱工作电压决定的. 对于矩形离子阱, 即使不考虑其几何结构的偏差, 其阱内的电场分布一般也很复杂. 在矩形离子阱内, 除四极电场外, 还包含多种成分的其他各种高阶场, 它们直接影响离子在阱内的运动轨迹和离子阱质谱的性能. 由于各种电场成分对离子阱内离子运动的影响非常复杂, 还很难从数学上给出精确的解析解, 使得目前从理论上还无法预测高阶场成分对质谱性能的影响. 本工作通过测定不同几何结构的矩形离子阱的稳定图, 从实验上比较了不同场半径, 即不同电场分布条件下的离子阱质谱性能的差别. 实验中, 通过改变离子阱的几何比例结构, 详细测定了不同结构的矩形离子阱的稳定图特征, 并与实验测得的质谱分析结果进行比较. 同时, 我们还详细介绍了矩形离子阱质谱的稳定图的测定方法, 并根据得到的不同情况下的稳定图结构分析了离子阱的质谱性能. 研究结果表明： 可以通过比较试验得到的稳定图结构来判断其离子阱质谱仪的性能如质量分辨能力等. 此外, 实验结果还发现： 对于y方向拉伸结构的矩形离子阱, 其实验绘制得到的是不完整的稳定图. 但根据稳定图边界的特点, 通过采用四极直流电压调制的方法, 可以对y方向拉伸结构的矩形离子阱的性能进行改善, 极大地提高了阱的质量分辨能力.     

气相色谱矩形离子阱质谱联用仪的设计与性能

气相色谱离子阱质谱联用仪(GC-ITMS)广泛地应用于药物分析、环境分析、农药检测和食品分析、有机化学品分析、毒品分析以及医学和生物分析等领域。离子阱质谱作为色谱的检测器,决定了色质联用仪的分析性能,包括检出限、分辨率。离子阱质量分析器从传统的双曲型3D离子阱发展到2D线性离子阱,质量歧视效应得到了极大的改善,灵敏度得到了提高。矩形离子阱作为线性离子阱,结构简单,加工和装配容易,因此应用到GCMS系统中将具有非常大的优势。介绍了矩形离子阱质谱仪的设计方案、仪器整机的性能测试、质量分辨和质量歧视效应分析,与Agilent6890组成GCMS联用仪,对实际样品进行了分析。     

离子阱阵列的理论模拟研究

采用电脑模拟的方法对一种新型的离子阱质量分析器——离子阱阵列进行了电极结构的优化.该离子阱质量分析器为一种多通道质量分析器,可以同时对不同的离子进行储存和质量分析.本实验主要研究了该离子阱质量分析器的性能和电极结构之间的关系.通过对离子运动轨迹的计算分析,可以得到模拟的离子质谱峰.通过对模拟离子质谱峰的分析,可以区分出使得离子阱性能较优的电极结构.在对模拟质谱峰的分析中,峰形和离子弹出效率都作为性能指标被考虑.有部分模拟的数据与实验结果进行了对比.     

阶梯电极离子阱质量分析器的结构与性能

本研究从理论上优化了一种新型结构的线型离子阱质量分析器-阶梯电极离子阱质量分析器,它是由2对阶梯电极与1对端盖电极组成。与传统平板电极矩形离子阱长阶梯电极离子阱相比,具有调节电场分布的优点,同时在几何结构设计上更接近于双曲面电极结构,但比双曲面电极更容易加工。通过改变阶梯电极结构的高度、宽度、场半径比例等几何参数,实现了对离子阱内部电场分布的优化,从而实现离子阱性能的优化。理论模拟研究结果表明,根据几何结构和电场分布优化获得的阶梯电极离子阱质量分析器(X0×Y0=9 mm×5 mm),可以在225 Da/ s 扫速下获得10150的质量分辨率。阶梯电极离子阱结构简单,分辨能力明显高于矩形离子阱。初步的实验结果表明,阶梯电极离子阱具有较好的串级质谱分析性能。     

印刷线路板分压离子阱的离子单向出射性能研究

印刷线路板(Printed-Circuit-Board,PCB)分压离子阱是一种新型质量分析器,其突出优点在于内部电场可通过调节射频分压比进行优化.本实验在PCB分压离子阱离子出射方向的两组离散电极上配置了非对称的射频分压,以引入奇次阶场成分,使得射频电场的场中心(即离子运动中心)发生偏移,从而实现离子单向出射.通过数值计算软件SIMION和AXSIM分析了射频分压比差值与其内部电场分布的关系,并模拟离子运动轨迹,得到离子出射情况和模拟质谱峰.模拟结果表明,当两组离散电极的射频分压比差值为20％时,在合适的AC频率条件下,对于m/z=609 Th的离子,PCB分压离子阱的离子单向出射率可达90％以上,且质量分辨率大于2500.本研究可使PCB分压离子阱在基本不损失质量分辨率和使用单检测器模式下,大幅提高离子检测效率,因而在小型化质谱仪应用中具有显著优势.     

用数字离子阱进行快速质量分析

利用数字离子阱技术进行样品的快速质量分析.在样品离子被引入离子阱的过程中,同时扫描数字射频工作电压的频率和离子共振偶极电压的频率,使得离子在进入离子阱质量分析器后,立即被相应的共振偶极电压所共振激发而逐出离子阱,并被离子探测器测量到.本方法相较于传统离子阱分析过程省去了离子引入、离子冷却和离子清空3个阶段,减少了约3/4的实验分析时间.通过对扫描速度、离子门电压参数的优化,数字束缚射频频率从1000～ 400 kHz线性扫描,扫描速度为2385 Th/s,离子门电压为9V,对利血平(m/z 609),精氨酸(m/z 174)等样品的进行测试,离子信号强度达到最优.结果表明,利用本方法可以获得与离子阱质量分析传统方法相同的质谱结果.     

数字离子阱质谱仪低质量截止值的改进方法

本研究在实验室自制的线形数字离子阱质量分析器上,通过改变数码电源的频率扫描方式,在CID过程中,通过扫描数字束缚方波电源的频率和数字激发方波的频率实现母体解离。例如对于利血平母体离子,当将离子数字束缚方波频率从500 kHz扫描到560 kHz,可以测量到低质荷比的碎片离子,成功实现了串级质谱分析的低质量碎片离子的分析。通过与利血平三重四极质谱串级质谱分析实验结果的比较,发现可以在数字离子阱质谱仪上获得与三重四极质谱相同的串级质谱测量结果。结果表明,本方法可以用于低质量离子的测量,克服了传统离子阱质谱进行串级质谱分析的一个主要难点,显著提高数字离子阱质谱的性能。     

食品中苏丹染料的高效液相色谱-离子阱质谱分析

提出了用高效液相色谱-离子阱质谱联用法同时鉴定和分析食品中四种苏丹染料的方法,色谱柱为Agilent Zorbax XB-C18,采用ESI离子源,离子阱质谱进行二级质谱分析,分析了苏丹染料分子在质谱中的碎裂方式,对碰撞解离电压进行了优化选择。方法检出限为1μg.L-1,线性范围为5~100μg.L-1,回收率在85.5%~97.0%之间。     

离子阱颗粒质谱研究进展

随着质谱技术的不断发展,对超高质量颗粒物质的分析已经成为质谱领域研究的一个重要方向.离子阱颗粒质谱(particle ion trap mass spectrometry)作为用于完整颗粒质量分析的有利工具,拓展了质谱技术在巨大颗粒物质量分析中的应用范围.本文对离子阱颗粒质谱仪器的研究进展及其在各个领域的应用进行了综述,并展望了离子阱颗粒质谱未来的发展趋势.     

半圆弧面线性离子阱性能优化的模拟研究

半圆弧面线性离子阱具有电极结构简单、便于加工和安装精度高等优点。为进一步提升半圆弧面线性离子阱的分析性能,本研究在实验室原有半圆弧面线性离子阱的基础上提出了一种四面开槽的半圆弧面线性离子阱,并对其电极半径与场半径之比r/r0以及离子出射方向上电极的“拉伸”距离进行了优化。模拟结果表明：当r/r0=5：5,离子出射方向上的电极向外“拉伸”0.8~1.2 mm时,离子阱的性能有较大提升,尤其是“拉伸”距离为0.9 mm时所得质量分辨率最高,当扫描速率为409 Da/s时, m/z=609 Da的离子质量分辨率可达到6264( M/△M, FWHM)。作为对比,本研究同时对双曲面线性离子阱的性能进行了仿真优化,结果表明,经过优化后的半圆弧面线性离子阱的性能可与双曲面线性离子阱相媲美。     

Multiplexed MS/MS in a Miniature Rectilinear Ion Trap

A multiplexed method for performing MS/MS on multiple ions simultaneously in a miniature rectilinear ion trap (RIT) mass spectrometer has been developed. This method uses an ion encoding procedure that relies on the mass bias that exists when ions are externally injected into an RIT operated with only a single phase rf applied to one pair of electrodes. The ion injection profile under such conditions ions is Gaussian-like over a wide range of rf amplitudes, or low mass cutoff (LMCO) values, during ion accumulation. We show that this distribution is related to ion m/z and is likely caused by ions having an optimal range of pseudo-potential well depths for efficient trapping. Based on this observation, precursor ion intensity changes between two different injection LMCO values can be predicted, and these ion intensity changes are found to be carried through to their corresponding product ions, enabling multiplexed MS/MS spectra to be deconvoluted.     

Novel linear ion trap mass analyzer composed of four planar electrodes

A novel linear ion trap mass analyzer was developed using just four elongated planar electrodes, mounted in parallel, and employing an RF potential for ion trapping in the radial and axial directions. Mass analysis was achieved using the mass-selective instability scan with ion ejection in the radial direction. The performance of this new device was characterized in comparison with the 6-electrode rectilinear ion trap (RIT) from which it is derived. The 4-electrode trap gives optimum performance in an asymmetric geometry, just like the original optimized 6-electrode RIT. The strong RF fringing fields at the ends of the RF rods account for axial ion trapping without use of extra electrodes or an axial DC voltage. Field calculations and simulations have been carried out to study the trapping potential inside RITs with various configurations. Demonstrated capabilities include analysis of externally injected ions with mass resolution in excess of 1000 and a mass/charge range of 650 Th as well as tandem mass spectrometry capabilities. The geometric simplicity and performance characteristics of the 4-electrode RIT make it particularly attractive in the development of next generation miniaturized mass spectrometers.     

Characterization of a DAPI-RIT-DAPI System for Gas-Phase Ion/Molecule and Ion/Ion Reactions

The discontinuous atmospheric pressure interface (DAPI) has been developed as a facile means for efficiently introducing ions generated at atmospheric pressure to an ion trap in vacuum [e.g., a rectilinear ion trap (RIT)] for mass analysis. Introduction of multiple beams of ions or neutral species through two DAPIs into a single RIT has been previously demonstrated. In this study, a home-built instrument with a DAPI-RIT-DAPI configuration has been characterized for the study of gas-phase ion/molecule and ion/ion reactions. The reaction species, including ions or neutrals, can be introduced from both ends of the RIT through the two DAPIs without complicated ion optics or differential pumping stages. The primary reactant ions were isolated prior to reaction and the product ions were mass analyzed after controlled reaction time period. Ion/molecule reactions involving peptide radical ions and proton-transfer ion/ion reactions have been carried out using this instrument. The gas dynamic effect due to the DAPI operation on internal energy deposition and the reactivity of peptide radical ions has been characterized. The DAPI-RIT-DAPI system also has a unique feature for allowing the ion reactions to be carried out at significantly elevated pressures (in 10^–1 Torr range), which has been found to be helpful to speed up the reactions. The viability and flexibility of the DAPI-RIT-DAPI system for the study of gas-phase ion reactions have been demonstrated.

Theoretical and numerical analysis of the behavior of ions injected into a quadrupole ion trap mass spectrometer

A numerical simulation method has been developed for the analysis of trapping ions injected into an ion trap mass spectrometer. This method was applied to clarify the effects of the following parameters on trapping efficiencies: (1) initial phase of the radio frequency (RF) drive voltage, (2) ion injection energy, and (3) RF peak voltage while injecting ions. The following conclusions were obtained by theoretical and simulation approaches. 1. The second and third dominant oscillations contribute significantly to the trapping mechanism of the injected ions, even for low q values. 2. A formula relating the operating parameters, which gives the maximum trapping efficiency, is derived. 3. Based on the above-mentioned formula, an advanced injection method is proposed, in which the RF peak voltage is decreased while injecting ions. The ability of this method to solve the problem of unequal sensitivity among different ion species is indicated by numerical simulation. Copyright 2000 John Wiley & Sons, Ltd.     

数字化矩形离子阱质谱仪的设计及性能

将数字化离子阱技术和矩形离子阱(RIT)技术相结合,建立了数字化矩形离子阱质谱仪.此技术和装置既具有数字化电源的结构简单、输出稳定和易精确控制等特点,又结合了矩形离子阱的高离子存储效率、结构简单以及加工和装配容易等优点.构建了基于电喷雾(ESI)电离源的数字化矩形离子阱质谱仪系统,并使用Fenfluramine和PPG2000分别对此系统的质量分辨率和质量范围进行了测试.研究结果表明:一个用印刷线路板(PCB)制作的简单矩形离子阱,在200 V(半峰值)的数字束缚电压的驱动下,获得了大于500的质量分辨率和超过2600 Th的质量范围.实验证明,数字化离子阱技术的应用可以显著提高矩形离子阱的性能,特别是质量范围等关键的质谱仪指标.     

Ion/molecule reactions in a miniature RIT mass spectrometer

Ion/molecule reactions were explored in a newly developed miniature mass spectrometer fitted with a rectilinear ion trap (RIT) mass analyzer. The tandem mass spectrometry performance of this instrument is demonstrated using collision induced dissociation (CID) and ion/molecule reactions. The latter includes Eberlin transacetalization reactions and electrophilic additions. Selective detection of the chemical warfare simulant dimethyl methyl phosphonate (DMMP) was achieved through selective Eberlin reactions of its characteristic phosphonium fragment ion CH3OP(+)(O)CH3 (m/z 93), with 1,4-dioxane or 1,3-dioxolane. Efficient adduct formation as a result of electrophilic attack by the phosphonium ion on various nucleophilic reagents, including 1,1,3,3-tetramethyl urea, methanesulfonic acid methyl ester, dimethyl sulfoxide and methyl salicylate, was also observed using the RIT device. The product ions of these reactions were analyzed using CID and the characteristic fragmentation patterns of the ionic addition products were recorded using multiple-stage experiments in the miniature RIT instrument. This study clearly demonstrates that a small, home-built, miniature RIT mass spectrometer can be used to perform analytically useful ion/molecule reactions and also that instruments like this have the potential to provide a portable platform for in situ detection of organophosphorus esters and related compounds with high specificity using tandem mass spectrometry.     

Kinetic energy effects in an ion ensemble subjected to mass-selective isolation and resonance excitation: A simulation study

A simulation study is described of the behaviour of ions confined in a quadrupole ion trap during each of two separate operations of a tandem mass spectrometric experiment. The two operations are those of mass-selective ion isolation and mass-selective resonance excitation to the point of ion ejection from the ion trap. The method of mass-selective ion isolation simulated is that of consecutive ion isolation. Simulation data indicate that the collisional history of the ions prior to the isolation process can greatly influence the degree to which ions survive this process. Simulation data for mass-selective resonance ejection are compared with experimental data obtained with a Finnigan-MAT ion trap mass spectrometer. In each operation, the facility with which ions absorb energy from the field within the ion trap, whether this field is derived from the R.F. drive potential or a supplementary potential, can determine the extent to which ions are retained within the ion trap during the two mass-selective operations described.     

Characterization of an Electron Ionization Source Trap Operating in the Presence of a Magnetic Field Through Computer Simulation

We explore the feasibility of conducting electron ionization (EI) in a radio-frequency (rf) ion source trap for mass spectrometry applications. Electrons are radially injected into a compact linear ion trap in the presence of a magnetic field used essentially to lengthen the path of the electrons in the trap. The device can either be used as a stand-alone mass spectrometer or can be coupled to a mass analyzer. The applied parallel magnetic field and the oscillating rf electric field produced by the trap give rise to a set of coupled Mathieu equations of motion. Via numerical simulations, electron trajectories are studied under varying intensities of the magnetic field in order to determine the conditions that enhance ion production. Likewise, the dynamic behavior of the ions are investigated in the proposed EI source trap and the fast Fourier transform FFT formalism is used to obtain the frequency spectrum from the numerical simulations to study the motional frequencies of the ions which include combinations of the low-frequency secular and the high-frequency micromotion with magnetron and cyclotron frequencies. The dependence of these motional frequencies on the trapping conditions is examined and particularly, the limits of applying a radial magnetic field to the EI ion trap are characterized.

Dual buffer gases for ion manipulation in a miniature ion trap mass spectrometer with a discontinuous atmospheric pressure interface

The discontinuous atmospheric pressure interface (DAPI) has been developed to allow a direct transfer of ions from atmosphere into an ion trap mass spectrometer with minimum pumping capability. Air is introduced into the trap with ions and used as a buffer gas for the ion trap operation. In this study, a method of introducing helium as a second buffer gas was developed for a miniature mass spectrometer using a dual DAPI configuration. The buffer gas effects on the performance of a linear ion trap (LIT) with hyperbolic electrodes were characterized for ion isolation, fragmentation and a mass-selective instability scan. Significant improvement was obtained with helium for resolutions of mass analysis and ion isolation, while moderate advantage was gained with air for collision-induced dissociation. The buffer gas can be switched between air and helium for different steps within a single scan, which allows further optimization of the instrument performance for tandem mass spectrometry.