化学水浴法制备大面积CdS薄膜及其光伏应用

采用化学水浴法制备了大面积CdS多晶薄膜,研究了薄膜的形貌、结构和光学性质,结果表明,大面积CdS多晶薄膜具有良好的均匀性,通过优化CdS多晶薄膜,制成了不同CdS窗口层厚度的CdTe小面积太阳电池,减薄CdS薄膜可有效提高器件的短路电流,改善器件性能.随后,在面积30cm×40cm的衬底上制备了全面积为993.6cm²的CdTe太阳电池组件,其27个集成单元的电学性质较为均匀,太阳电池组件的光电转换效率8.13%. 关键词： 化学水浴法(CBD) CdS薄膜 CdTe太阳电池 CdTe太阳电池组件     

近空间升华法制备CdS多晶薄膜的研究

系统地研究了近空间升华法(CSS)制备CdS薄膜沉积速率的影响因素。发现CdS薄膜的沉积速率随升华源温度的升高而增大,但随衬底温度和沉积气压的上升而下降。对所制备样品的结构、表面形貌和光谱透过率特性进行了测试,结果表明：(1)不同氧分压下沉积的CdS薄膜沿(103)晶向择优生长。CdCl₂氛围下退火后,(103)晶向的优势得到进一步加强;(2)不同氧分压制备的CdS薄膜致密且粒径均匀,晶粒的大小随着衬底温度的升高而增大,但薄膜的粗糙度也随之增大;(3)随着CdS薄膜厚度的减小,可见光中短波段的透过率有所增大,有利于提高太阳电池的短波光谱响应。并将CSS制备的CdS多晶薄膜用于CdTe太阳电池的制作,获得了10.29%的光电转换效率,初步验证了该制作工艺的可行性。     

具有高阻抗本征SnO2过渡层的CdS/CdTe多晶薄膜太阳电池

采用超声喷雾热解法制备了具有高阻抗的本征SnO₂透明导电膜，将其运用在CdS层减薄了的CdS/CdTe多晶薄膜太阳电池中，对减薄后的CdS薄膜进行了XRD,AFM图谱分析，并对电池进行了光、暗I-V，光谱响应和C-V测试.结果表明，在高阻膜上沉积的减薄CdS薄膜(111)取向更明显，但易形成微孔.引入高阻层后，能消除CdS微孔形成的微小漏电通道，有效保护p-n结，改善了电池的并联电阻、填充因子和短波响应，使载流子浓度增加，暗饱和电流密度减小，从而电池性能得到改善，电池转换效率增加了14.4%. 关键词： CdTe电池 过渡层 效率     

氧对于在Ar/O氛围下用近空间升华法制备的CdS薄膜的影响

采用近空间升华法（CSS）在氩/氧气氛中制备了硫化镉（CdS）多晶薄膜.利用XRD,XPS,AFM,UV-VIS光谱和四探针技术等测试和分析手段系统研究了氧对薄膜的成分、结构、光学和电学等性质的影响.结果表明,用近空间升华法制备的CdS薄膜具有六方相结构,膜层致密、均匀,平均晶粒大小约为40 nm,富硫.氧掺入后部分与镉生成氧化镉,并随着氧含量的增加,薄膜的成分有趋于化学计量比的趋势,光学带隙加宽,光暗电导比增加.此外,还利用扫描电镜（SEM）观察了CdS/CdTe断面结合光谱响应（QE）的结果讨论了氧对CdS/CdTe界面互扩散的影响.发现,随着CdS薄膜制备气氛中氧分压的升高,CdS/CdTe界面的互扩散程度降低,有利于提高器件在500—600 nm波长范围内的光谱响应.认为,氧含量的增加不但使CdS薄膜在光伏应用方面的质量得到改善,而且CdTe太阳电池器件中的CdS/CdTe界面也得到了优化. 关键词： CdS多晶薄膜 近空间升华法 窗口层 界面     

具有高阻抗本征SnO2过渡层的CdS/CdTe多晶薄膜太阳电池

采用超声喷雾热解法制备了具有高阻抗的本征SnO2透明导电膜,将其运用在CdS层减薄了的CdS/CdTe多晶薄膜太阳电池中,对减薄后的CdS薄膜进行了XRD,AFM图谱分析,并对电池进行了光、暗I-V,光谱响应和C-V测试.结果表明,在高阻膜上沉积的减薄CdS薄膜(111)取向更明显,但易形成微孔.引入高阻层后,能消除CdS微孔形成的微小漏电通道,有效保护p-n结,改善了电池的并联电阻、填充因子和短波响应,使载流子浓度增加,暗饱和电流密度减小,从而电池性能得到改善,电池转换效率增加了14.4%.     

弱光下锑基太阳电池的光谱响应与性能优化

锑基薄膜太阳电池因其制备方法简单,原材料丰富,光电性能稳定等优点而得到了快速发展。其中锑基吸光层材料(硫化锑、硫硒化锑、硒化锑)具有高吸收系数特点,因而在室内或者水下等弱光条件下具有相当大的应用潜力。通过构造两种衰减光谱以研究新型锑基薄膜太阳电池在弱光下的光电响应。首先通过厚度调节硒化锑太阳电池的吸光能力,发现当吸光层厚度较薄时,电池的光电转换效率存在较大差值;而当吸光层厚度过厚时,电池性能又因载流子复合的增大而降低。在吸光层厚度处于合适的0.4～1.2μm之间时,硒化锑太阳电池在长波衰减光谱和短波衰减光谱下都能获得高于16%的转换效率。然后通过硒含量调节锑基太阳电池的光谱吸收范围,发现长波衰减光谱下,锑基太阳电池的器件性能显著高于标准光谱,并且在20%～40%硒含量下能够获得最佳的转换效率。而在短波衰减光谱下,锑基太阳电池的最佳性能出现在硒含量为60%的情况下。因而在弱光条件下,锑基太阳电池的最佳硒含量需要通过具体的光谱特性确定。最后研究了两种衰减光谱下,硫化锑/硒化锑双结叠层太阳电池的光谱响应特性。发现在短波衰减光谱下,叠层太阳电池效率会随着总厚度的增加而增加。而在长波衰减光谱下,...     

CdTe多晶薄膜沉积制备及其性能

在氩气和氧气混合气氛下,近空间升华法制备了CdTe多晶薄膜。薄膜的结构、性质决定于整个沉积过程。深入研究沉积过程中的热交换、物质输运,有助于获得结构致密具有良好光电性质的CdTe薄膜。分析了近空问沉积的物理机制,测量了近空间沉积装置内的温度分布,讨论了升温过程、气压与薄膜的初期成核的关系。结果表明,不同气压下制备的样品,均有立方相CdTe。此外,还有CdS和SnO2：F衍射峰。CdTe晶粒随气压增加有减小趋势;随气压的增加,透过率呈下降趋势,相应的CdTe吸收边向短波方向移动。采用衬底温度500℃,源温度620℃,在120℃的温差下,沉积时间4min上制备CdTe多晶薄膜,获得转换效率优良的结构为SnO2：F／CdS／CdTe／Au的集成电池。     

图谱分析退火对本征SnO2多晶薄膜性能的影响

提高CdTe太阳电池转换效率的有效途径之一是适当减薄CdS窗口层,减薄了的CdS层会严重影响电池性能,解决方法是在窗口层和透明导电膜之间加一层高阻本征SnO2薄膜。采用反应磁控溅射制备了具有高阻抗的本征SnO2薄膜,并对其进行了后处理,利用XRD,XPS等方法研究了退火前后薄膜的结构,成分及表面化学状态的变化。结果表明:经N2/O2=4:1气氛550℃(0.5h)退火后,样品由非晶态转变为四方相结构的多晶薄膜,具有(110)择优取向;XPS分析表明退火后薄膜的氧含量增加、O(1s)峰向低能方向移动,SnO被氧化成SnO2,使得薄膜的透过率增大,退火后的本征SnO2高阻膜非常适合作为过渡层应用于CdTe太阳电池中。     

CdTe太阳电池前电极SnO2:F/SnO2复合薄膜性能分析

减薄CdS窗口层是提高CdS/CdTe太阳电池转换效率的有效途径之一,减薄窗口层会对器件造成不利的影响,因此在减薄了的窗口层与前电极之间引入过渡层非常必要.利用反应磁控溅射法在前电极SnO₂:F薄膜衬底上制备未掺杂的SnO₂薄膜形成过渡层,并将其在N₂/O₂=4 ∶1,550 ℃环境进行了30 min热处理,利用原子力显微镜、X射线衍射仪、紫外分光光度计对复合薄膜热处理前后的形貌、结构、光学性能进行了表征,同时分析了复     

不同温度下制备的CdTe薄膜对太阳电池光电性能的影响

在不同温度下用近空间升华法（CSS）制备了CdTe多晶薄膜,结合I-V,C-V特性及深能级瞬态谱研究了不同温度制备的CdTe薄膜对CdS/CdTe太阳电池性能的影响.结果表明,制备温度对电池组件的开路电压影响不大,对短路电流和填充因子有影响,CdTe薄膜的深中心对温度和频率的响应基本一致.580℃制备的样品暗饱和电流密度最小,载流子浓度较高,光电特性较好,而且空穴陷阱浓度较低,深中心复合作用较小.在此研究基础上制备出了面积为300 mm×400 mm 关键词： 制备温度 CdTe薄膜 深能级瞬态谱（DLTS） CdS/CdTe太阳电池     

Preparation and characterization of ZnS/CdS bi-layer for CdTe solar cell application

In this work, bilayer ZnS/CdS film was prepared as an improved window layer of CdTe solar cell. TEM was used to observe the cross section of the bilayer structure. The total thickness of ZnS/CdS film was about 60 nm, which could allow more photons to pass through it and contribute to the photocurrent. Optical properties of the bilayers were investigated using UV–vis spectroscopy. Compared with poor transmission of standard CdS film in the short wavelength range of 350–550 nm, the transmission of ZnS/CdS was improved and reached above 50%. The ZnS/CdS was annealed with CdCl₂. X-ray photoelectron spectroscopy (XPS) was used to investigate its chemical properties. A possible diffusion between CdS and ZnS was observed after annealing. The efficiency of standard CdS/CdTe solar cell was 9.53%. The device based on ZnS/CdS window layer had a poor 6% efficiency. With annealing treatment on ZnS/CdS layer, the performance was improved and reached 10.3%. In addition, the homogeneity of solar cell performance was improved using ZnS/CdS window layer. A thin ZnS layer was quite effective to reduce the possible shunt paths and short parts of window layer and consequently contributed to fabrication of a homogeneous CdTe solar cell.     

Short-circuit current improvement in CdTe solar cells by combining a ZnO buffer layer and a solution back contact

Conventional CdTe solar cells have a CdS window layer, in which an absorption loss of photons with more than 2.4 eV occurs through the CdS layer. A thinner CdS layer was applied to enhance light transmission and a ZnO buffer layer with a band gap of 3.3 eV was introduced to suppress shunting through the thinner CdS window layer. A 100-nm thick ZnO layer sputter-deposited at 300 °C had uniform coverage on a transparent conductive oxide (TCO) after a subsequent high-temperature process. The ZnO layer was effective in preventing shunting through the CdS window layer so that the open-circuit voltage and fill factor of the CdTe solar cells were recovered and the short-circuit current was enhanced over that of the conventional CdTe solar cell. In the ZnO/CdS/CdTe configuration, the short-circuit current was further improved throughout the visible wavelength region by replacing the Cu-metal contact with a Cu solution contact. As a result the short-circuit current from 21.7 to 26.1 mA/cm² and the conversion efficiency of the CdTe solar cell increased from 12 to 15% without antireflective coating. Our result indicates that the Cu solution back contact is a critical factor for achieving a higher cell efficiency in addition to ZnO buffer layer.     

碲化镉薄膜太阳能电池电学特性参数分析

用inline方式全部近空间升华方法制备n-CdS/p-CdTe取得了～11%的转换效率(AM1.5). 把其中n-CdS层采用磁控溅射方法取得了～10%的转换效率(AM1.5). 基于其电流密度-电压(J-V)曲线和外量子效率曲线, 分析了其拟合关键参数对于电池性能的影响程度, 并从理论分析上把目前器件性能参数与当今前沿性能参数以及其理论值进行比较, 指出了如何提高电池转换效率(η)的方法: 提高开路电压(V_oc)、短路电流(J_sc)和填充因子(FF). 关键词： 碲化镉电池 电流密度-电压曲线 外量子效率曲线 电学特性     

Performance improvement in CdTe solar cells by modifying the CdS/CdTe interface with a Cd treatment

The performance of n-CdS/p-CdTe solar cells is often degraded under light soaking or thermal stress, even though the technology of CdTe solar cells is close to a commercial level. The Cu diffusion from a Cu back contact to a CdS window layer might degrade the cell's performance. To prevent the Cu diffusion, a very-thin intrinsic CdTe layer was introduced at the n-CdS/p-CdTe interface by depositing a very-thin Cd metal layer on the CdS film and converting the Cd metal into intrinsic CdTe during p-CdTe deposition at high temperature. By the Cd treatment on CdS surface, pinholes or voids were eliminated at the CdS/CdTe and the intermixing of Te and S at the interface was much suppressed. The depletion width was much increased and the intensity of LTPL peak was increased. The analysis suggested that an intrinsic CdTe interlayer was formed and the surface recombination rate was suppressed by the intrinsic interlayer. As a result, the short circuit current of the CdTe solar cell was significantly increased due the increased current gain in the blue wavelength region. The thermal stability of the CdTe solar cell was also greatly improved and the Cu diffusion was retarded by the intrinsic CdTe interlayer at the n-CdS/p-CdTe.     

Recombination-induced voltage-dependent photocurrent collection loss in CdTe thin film solar cell

Recently, the efficiency of CdTe thin film solar cell has been improved by using new type of window layer Mg_xZn_1-xO (MZO). However, it is hard to achieve such a high efficiency as expected. In this report a comparative study is carried out between the MZO/CdTe and CdS/CdTe solar cells to investigate the factors affecting the device performance of MZO/CdTe solar cells. The efficiency loss quantified by voltage-dependent photocurrent collection efficiency (η_C(V')) is 3.89% for MZO/CdTe and 1.53% for CdS/CdTe solar cells. The higher efficiency loss for the MZO/CdTe solar cell is induced by more severe carrier recombination at the MZO/CdTe p—n junction interface and in CdTe bulk region than that for the CdS/CdTe solar cell. Activation energy (E_a) of the reverse saturation current of the MZO/CdTe and CdS/CdTe solar cells are found to be 1.08 eV and 1.36 eV, respectively. These values indicate that for the CdS/CdTe solar cell the carrier recombination is dominated by bulk Shockley—Read—Hall (SRH) recombination and for the MZO/CdTe solar cell the carrier recombination is dominated by the p—n junction interface recombination. It is found that the tunneling-enhanced interface recombination is also involved in carrier recombination in the MZO/CdTe solar cell. This work demonstrates the poor device performance of the MZO/CdTe solar cell is induced by more severe interface and bulk recombination than that of the CdS/CdTe solar cell.     

Cell labeling and cytotoxicity of aqueously synthesized CdTe/CdS/ZnS core–shell–shell quantum dots by a water bath-hydrothermal method

CdTe/CdS/ZnS core–shell–shell quantum dots (QDs) were synthesized in aqueous solution via water-bathing combined hydrothermal method using L-cysteine as a stabilizer. The present method features markedly reduced synthesis time, higher fluorescent intensity and lower cytotoxicity of the QDs. Structural and spectroscopic properties of core–shell–shell QDs are well characterized by absorption and fluorescence spectroscopy, X-ray diffraction, transmission electron microscopy, and fourier transform infrared spectroscopy. Both CdS and ZnS shells were capped on the CdTe core and the fluorescence was greatly enhanced by the ZnS coating. The ternary QDs conjugated with transferrins were successfully employed for the biolabeling and fluorescent imaging of HeLa cells. Cytotoxicity evaluation shows that CdTe/CdS/ZnS was less toxic for cells than CdTe and CdTe/CdS due to the presence of a ZnS coating on surface, which inhibited the release of cadmium ions.     

Short‐circuit current improvement of CuGaSe2 solar cells with a ZnS/(Zn,Mg)O buffer combination

CuGaSe₂ (CGS) thin‐film solar cells were prepared with an in‐line co‐evaporation process and the established buffer combination CdS/i‐ZnO was replaced by ZnS/(Zn,Mg)O. We obtained functional CGS solar cells with a strong gain in the short‐circuit current density as compared to the CdS/i‐ZnO buffer reference cells. The enhanced current density is a result of improved transmission in the wavelength region between 330 nm and 550 nm of the ZnS/(Zn,Mg)O buffer combination as compared to CdS/i‐ZnO. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Facile synthesis of mercaptosuccinic acid-capped CdTe/CdS/ZnS core/double shell quantum dots with improved cell viability on different cancer cells and normal cells

Water-soluble, mercaptosuccinic acid (MSA)-capped CdTe/CdS/ZnS core/double shell quantum dots (QDs) were prepared by successive growth of CdS and ZnS shells on the as-synthesized CdTe/CdS_thin core/shell quantum dots. The formation of core/double shell structured QDs was investigated by ultraviolet-visible (UV–Vis) absorption and photoluminescence (PL) spectroscopy, PL decay studies, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The core/double shell QDs exhibited good photoluminescence quantum yield (PLQY) which is 70% higher than that of the parent core/shell QDs, and they are stable for months. The average particle size of the core/double shell QDs was ～3 nm as calculated from the transmission electron microscope (TEM) images. The cytotoxicity of the QDs was evaluated on a variety of cancer cells such as HeLa, MCF-7, A549, and normal Vero cells by 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) cell viability assay. The results showed that core/double shell QDs were less toxic to the cells when compared to the parent core/shell QDs. MCF-7 cells showed proliferation on incubation with QDs, and this is attributed to the metalloestrogenic activity of cadmium ions released from QDs. The core/double shell CdTe/CdS/ZnS (CSS) QDs were conjugated with transferrin and successfully employed for the biolabeling and fluorescent imaging of HeLa cells. These core/double shell QDs are highly promising fluorescent probe for cancer cell labeling and imaging applications.