LaB_6 Work Function and Structural Stability under High Pressure

The work functions of the(110) and(100) surfaces of LaB_6 are determined from ambient pressure to 39.1 GPa.The work function of the(110) surface slowly decreases but that of the(100) surface remains at a relatively constant value. To determine the reason for this difference, the electron density distribution(EDD) is determined from high-pressure single-crystal x-ray diffraction data by the maximum entropy method. The EDD results show that the chemical bond properties in LaB_6 play a key role. The structural stability of LaB6 under high pressure is also investigated by single-crystal x-ray diffraction. In this study, no structural or electronic phase transition is observed from ambient pressure to 39.1 GPa.     

适用于非常规工作环境中热释电型激光能量计的研制

现有的激光能量计传感器灵敏度系数都与其所处环境温度有关,在-50℃～70℃的温度范围内,灵敏度偏差较大,直接影响测量结果。为了达到消除环境温度的影响,采取在不同环境温度下对热释型能量计的灵敏度进行校准的研究方法。该校准方法与普通激光能量计的校准方法的不同之处在于对热释电型能量计进行校准时,温度由室温扩展到-50℃～70℃的温度范围。利用环境试验箱,每隔10℃固定一个温度点,进行激光能量的测量实验,得到各个温度点所对应的灵敏度修正系数,再借助最小二乘法建立起各个温度点上能量计灵敏度系数同环境温度的函数关系,从而实现了-50℃～70℃的温度范围内激光能量的准确计量。研制能直接工作于非常规工作环境下的热释电型激光能量计,对解决激光能量测量的外场需求有一定现实意义。     

一种气压传感器新型标定补偿方法（英）

通常气压传感器的标定补偿方法复杂耗时,开发了一种新的方法去简化气压传感器的标定补偿。首先,设计恒温结构,并通过PID算法自动调节,使气压传感器的核心敏感元件工作于某一个固定温度（此温度稍高于气压传感器需要工作的最高温度点）;其次,把气压传感器在与这个固定温度点相等的环境温度下进行标定;最后,完成标定后不管环境温度如何变化,气压传感器敏感元件始终工作在一个恒定的温度,因此气压传感器的标定与补偿可以得到简化。经测试,气压传感器在一定的环境温度范围内实现恒温工作,标定后可以以较高的精度测量气压,实验结果表明经过标定补偿后的气压传感器可以在实际中应用。     

The effect of ocean wave on the vertical spatial correlation of ocean ambient noise

The effect of the correlation function of noise sources derived from the ocean wave spectrum on the vertical spatial correlation of ocean ambient noise is investigated. The spatial correlation models of ocean ambient noise usually assume that the surface noise sources are uncorrelated. This assumption can be used to explain some physical phenomena, but it is not consistent with the real situation. Considering the relation between the ocean wave motion and the ambient noise generated by wind, the spectrum of ocean wave is introduced to calculate the vertical correlation of ocean ambient noise as the correlation function of noise sources by using the Kuperman-Ingenito(K/I) noise model. The comparison of the simulations and the experimental data shows that the simulations of vertical correlation of ambient noise have some differences with the experimental data by assuming the noise sources are uncorrelated and the simulations of vertical correlation of ambient noise have a good agreement with the experimental data by using the correlation function of noise sources derived from the ocean wave spectrum under the situation of high wind speed.     

海面波浪对海洋环境噪声垂直空间相关性的影响

研究了由海浪谱导得的噪声源的相关函数对海洋环境噪声垂直空间相关性的影响。常用的海洋环境噪声空间相关性模型一般假设海面噪声源是非相关的,这种假设可以解释一些物理现象,但是与真实情况并不符合。考虑到风成噪声与海浪运动的相关性,引入海浪谱,得到噪声源的相关函数,利用Kuperman-Ingenito (K/I)噪声模型,计算海洋环境噪声的垂直相关性。通过仿真结果与实验数据对比可以看出,在高风速下,假设噪声源不相关时计算得到的噪声场垂直相关性与实验结果相差较大,而利用由海浪谱导得的噪声源的相关函数计算得到的噪声场的垂直相关性与实验结果符合较好。      

利用海浪噪声自相关实现散射体无源探测

提出了一种利用海浪噪声自相关实现散射体无源探测的新方法.将各接收器记录噪声信号的自相关减去所有接收器记录噪声信号自相关的平均值,得到散射信号的到达结构,然后结合基尔霍夫移位算法实现对散射体的探测.与利用背景噪声互相关提取格林函数从而实现散射体探测的方法不同,自相关无需考虑各个接收器之间的大量数据传输及时间同步问题,这为相距较远的多接收器和移动平台目标探测提供了极大的方便.将所提出的方法应用于实验数据中,最终探测结果与实际测量结果相比差别不大,验证了方法的有效性.     

基于接触势差法的表面功函数测试装置

利用接触势差法自行设计开发了一种新型的表面功函数测试装置。基本原理是参考电极与样品之间形成电容,计算流过参考电极与样品之间的电流,通过确定电流的零点来获得功函数。此测量仪器由函数发生、功率放大、振荡器等多个功能模块组成。能在空气环境中快速测量半导体、金属、金属氧化物薄膜的表面功函数。我们运用此装置成功地对有机电致发光的阳极氧化铟锡(ITO)薄膜、p型硅片的功函数进行了测量,得到了样品经过UV-Ozone处理前后功函数随时间变化的曲线,为器件的优化提供了依据。     

Characteristics of DC discharge in a wire-cylinder configuration at high ambient temperatures

In the present work, the characteristics of direct-current (DC) discharge in a wire-cylinder configuration at an ambient temperature range of 350–850 °C were studied by analyzing photographs of the discharging process and the corresponding V–I characteristics, with the aim of facilitating the application of plasma technology in the fields of energy and the environment. The influences of the ambient temperature, the inter-electrode gap, the gas medium and the cathode material on the DC discharge were investigated. The corona-onset threshold voltage (COTV) and the spark-breakdown threshold voltage (SBTV) decrease as the ambient temperature increases, and the SBTV decreases more rapidly. Increasing the inter-electrode gap enlarges the difference between the SBTV and the COTV. After spark breakdown, in an air atmosphere, glow discharge is more likely to take place under conditions of high ambient temperatures or small inter-electrode gaps. The values of the SBTV in different atmospheres have the following relation: air ≈ O₂ > CO₂. At an ambient temperature range of 350–850 °C and in an atmosphere of N₂, glow discharge and arc discharge occur successively as the output voltage of the power supply is increased, while in an atmosphere of O₂ and CO₂, only corona and arc discharge are successively observed. In an air atmosphere, when the inter-electrode gap is 29 mm, corona, glow and arc discharge occur successively with increasing output voltage when the ambient temperature is 850 °C, while only corona and arc discharge appear when the temperature is 350–750 °C. When the inter-electrode gap is 5 mm in an air atmosphere, corona, glow and arc discharge occur successively in an ambient temperature range of 350–850 °C. The cathode material has a minor influence on the COTV and a more significant influence on the SBTV. In a device using a cathode with a low work function, the SBTV is low, and the power to maintain arc discharge is small.     

Role of ambient gas in heating of metal samples by femtosecond pulses of laser radiation

In this work we consider an experimentally observed effect of significant increasing of the residual heat in metal targets at their irradiation with femtosecond laser pulses in an ambient gas in respect to the vacuum conditions. Numerical modelling of heating of a platinum target by femtosecond laser pulses in argon under normal conditions has been performed taking into account gas breakdown in the focussing region of the laser beam in front of the target. The applied model is based on a combination of a thermal model describing heating and phase transitions in irradiated samples and a hydrodynamic model to describe motion of the ambient gas perturbed by laser irradiation as a result of multiphoton ionization. The hot ambient gas is shown to heat efficiently the irradiated sample. The hydrodynamic processes in the ambient gas play an important role in heating. This work was financially supported by the Russian Foundation for Basic Research (Project 08-01-00264-a) and the INTAS/SB RAS Program (Project 06-1000013-8949).     

Residual gas properties in a field emission device with ZnO emitters

In this paper, a vacuum system is employed to compare the emission stabilities of the same ZnO cathode in a sealed field emission （FE） device and under ultrahigh vacuum （UHV） conditions. It is observed that the emission current is more stable under the UHV level than in the device. When all conditions except the ambient gases are kept unchanged, the emission current degradation is mainly caused by the residual gases in the sealed device. The quadrupole mass spectrometer （QMS） equipped on the vacuum system is used to investigate the residual gas components. Based on the obtained QMS data, the following conclusions can be drawn： the residual gases in ZnO-FE devices are H2, CH4, CO, Ar, and CO2. These residual gases can change the work function at the surface through adsorption or ion bombardment, thereby degrading the emission current of the cathode.     

利用海洋环境噪声直接提取海底反射系数

提出了一种利用海洋环境噪声直接(非迭代)提取海底反射系数的方法,基于海洋环境噪声垂直相关函数与方向密度函数的相似性,结合海洋环境噪声射线理论,由两个垂直排列的水听器实现海底反射系数的被动获取.方法适应性的仿真分析说明较高海况下且近场无航船干扰的海洋环境噪声数据有利于方法的实现;对于两层海底,海洋环境噪声垂直相干函数经高...     

Arrival-time structure of the time-averaged ambient noise cross-correlation function in an oceanic waveguide

Coherent deterministic arrival times can be extracted from the derivative of the time-averaged ambient noise cross-correlation function between two receivers. These coherent arrival times are related to those of the time-domain Green's function between these two receivers and have been observed experimentally in various environments and frequency range of interest (e.g., in ultrasonics, seismology, or underwater acoustics). This nonintuitive result can be demonstrated based on a simple time-domain image formulation of the noise cross-correlation function, for a uniform distribution of noise sources in a Pekeris waveguide. This image formulation determines the influence of the noise-source distribution (in range and depth) as well as the dependence on the receiver bandwidth for the arrival-time structure of the derivative of the cross-correlation function. These results are compared with previously derived formulations of the ambient noise cross-correlation function. Practical implications of these results for sea experiments are also discussed.     

利用环境噪声互相关实现散射体无源成像

最近研究表明利用环境噪声的互相关可以恢复两点之间的时域格林函数(声脉冲响应),这一原理在文献中被称为格林函数恢复。基于此原理,通过对多个传声器所接收的环境噪声进行互相关处理,获取与散射体相关联的散射波的到达时延信息,结合最小二乘反演算法和改进克希霍夫移位算法,分别获得道路交通噪声场中石柱以及海浪噪声场中塑料桶的空间位置,且其估计结果与实际测量相一致。实验结果表明将环境噪声作为探测信号进行散射体无源成像是可行的。这为设计室内无源声监测系统以及通过海洋环境噪声实现对水中静默目标成像提供了新思路和有益参考。      

Application of time reversal to passive acoustic remote sensing of the ocean

This paper investigates a novel approach to processing records of ambient noise in the ocean that are measured concurrently in spatially separated locations. The approach is a synthesis of two well-known phase-coherent signal processing techniques. At the first stage of processing, an approximation to the transient acoustic Green function is found by the method of noise interferometry. At the second stage, the approximate Green function is time reversed and back propagated from the location of one of the receivers, thereby producing a focus in the vicinity of the other receiver. Unlike the earlier work, measurements at just two points (rather than vertical array measurements) are used when the sound-propagation range is large compared to the ocean depth. The requirement for optimal focusing of the back-propagated field is shown to lead to extraction of estimates of the unknown physical parameters of the waveguide and, hence, to passive acoustic remote sensing of the ocean.     

Reliability of single aliquot regenerative protocol (SAR) for dose estimation in quartz at different burial temperatures: A simulation study

The single aliquot regenerative protocol (SAR) is a well-established technique for estimating naturally acquired radiation doses in quartz. This simulation work examines the reliability of SAR protocol for samples which experienced different ambient temperatures in nature in the range of −10 to 40 °C. The contribution of various experimental variables used in SAR protocols to the accuracy and precision of the method is simulated for different ambient temperatures. Specifically the effects of paleo-dose, test dose, pre-heating temperature and cut-heat temperature on the accuracy of equivalent dose (ED) estimation are simulated by using random combinations of the concentrations of traps and centers using a previously published comprehensive quartz model. The findings suggest that the ambient temperature has a significant bearing on the reliability of natural dose estimation using SAR protocol, especially for ambient temperatures above 0 °C. The main source of these inaccuracies seems to be thermal sensitization of the quartz samples caused by the well-known thermal transfer of holes between luminescence centers in quartz. The simulations suggest that most of this inaccuracy in the dose estimation can be removed by delivering the laboratory doses in pulses (pulsed irradiation procedures).     

单边噪声源环境下的格林函数提取

对单边噪声源环境下空间中存在散射体时的格林函数到达时间结构提取展开了实验性研究。通过对位于沙滩上的传声器上记录的海浪噪声进行互相关处理,成功提取出两传声器间的格林函数到达时间结构。到达时间结构中观察到伪散射路径,并且伪散射路径在幅值上远高于散射路径。针对上述现象给出了理论及仿真解释:当传声器对受噪声源单边照射时,广义光学定理失效,伪散射路径将会出现;同时,由于伪散射路径由所有方向噪声源贡献,散射路径仅有稳相点附近声源贡献,因此伪散射路径在幅值上可能高于散射路径。结果表明,在单边噪声源环境下,基于互相关技术可以提取伪散射路径。伪散射路径的短时稳定提取可以为散射体无源成像提供更多信息,在海洋声学、地震学等领域具有潜在应用价值。      

Effect of temperature on the electron field emission from aligned carbon nanofibers and multiwalled carbon nanotubes

Effect of temperature and aspect ratio on the field emission properties of vertically aligned carbon nanofiber and multiwalled carbon nanotube thin films were studied in detail. Carbon nanofibers and multiwalled carbon nanotube have been synthesized on Si substrates via direct current plasma enhanced chemical vapor deposition technique. Surface morphologies of the films have been studied by a scanning electron microscope, transmission electron microscope and an atomic force microscope. It is found that the threshold field and the emission current density are dependent on the ambient temperature as well as on the aspect ratio of the carbon nanostructure. The threshold field for carbon nanofibers was found to decrease from 5.1 to 2.6 V/μm when the temperature was raised from 300 to 650 K, whereas for MWCNTs it was found to decrease from 4.0 to 1.4 V/μm. This dependence was due to the change in work function of the nanofibers and nanotubes with temperature. The field enhancement factor, current density and the dependence of the effective work function with temperature and with aspect ratio were calculated and we have tried to explain the emission mechanism.     

Spatial correlation in the ambient core noise field of a turbofan engine

An acoustic transfer function relating combustion noise and turbine exit noise in the presence of enclosed ambient core noise is investigated using a dynamic system model and an acoustic system model for the particular turbofan engine studied and for a range of operating conditions. Measurements of cross-spectra magnitude and phase between the combustor and turbine exit and auto-spectra at the turbine exit and combustor are used to show the presence of indirect and direct combustion noise over the frequency range of 0-400 Hz. The procedure used evaluates the ratio of direct to indirect combustion noise. The procedure used also evaluates the post-combustion residence time in the combustor which is a factor in the formation of thermal NO(x) and soot in this region. These measurements are masked by the ambient core noise sound field in this frequency range which is observable since the transducers are situated within an acoustic wavelength of one another. An ambient core noise field model based on one and two dimensional spatial correlation functions is used to replicate the spatially correlated response of the pair of transducers. The spatial correlation function increases measured attenuation due to destructive interference and masks the true attenuation of the turbine.     

Prototypical single-molecule chemical-field-effect transistor with nanometer-sized gates

A prototypical single-molecule chemical-field-effect transistor is presented, in which the current through a hybrid-molecular diode is modified by nanometer-sized charge transfer complexes covalently linked to a molecule in an STM junction. The effect is attributed to an interface dipole which shifts the substrate work function by approximately 120 meV. It is induced by the complexes from electron acceptors covalently bound to the molecule in the gap and electron donors coming from the ambient fluid. This proof of principle is regarded as a major step towards monomolecular electronic devices.