5,6,11,12-四苯基四苯并掺杂8-羟基喹啉铝薄膜的荧光谱及发光机理

用高荧光染料的5，6，11，12－四苯基四苯并对8－羟基喹啉铝进行掺杂，测量其光致发光和电致发光谱。结果表明：在低掺杂时，主发光体是Alq，掺入的Rubrene作为客发光体只是在Alq带隙中引入了分立能级；随着掺入的Rubrene浓度增加，Rubrene成了主发光体，Alq变成了客发光体，出现了发光体的互换现象。由于Rubrene的吸收光谱与Alq的发射谱重叠较大，在光致发光中存在从Alq向Rubrene的能量传递和电荷转移过程，而电致发光则是由于Rubrene导带中电子浓度远大于注入到Alq导带中电子浓度，造成Rubrene导带电子与价带空穴复合的几率比Alq中的复合几率大得多，其EL主要是Rubrene的发光。     

磷光染料掺杂有机分子发光的能量转移研究

用稳态光谱和时间分辨的超快光谱研究了不同浓度磷光染料PtOEP掺杂有机小分子Alq薄膜的发光特性和能量转移.据PtOEP的吸收光谱与Alq的荧光光谱,用Frster理论估算出Alq:PtOEP掺杂体系的能量转移临界半径及其转移效率.稳态荧光光谱显示,在Alq:PtOEP掺杂薄膜中,随着掺杂浓度的升高,PtOEP的发光强度增强,Alq的发光强度逐渐减弱,两者间的能量转移效率与理论计算结果一致.利用时间分辨光谱研究了Alq:PtOEP掺杂薄膜体系的能量转移动力学过程,观察到Alq:PtOEP掺杂薄膜的荧光寿 关键词： 有机掺杂薄膜 稳态光谱 时间分辨光谱 能量转移     

一种新型结构的黄光有机电致发光器件

用有机荧光染料罗丹明B(Rhodamine B)作为掺杂剂, 采用双量子阱结构制备了一种新型的黄光有机电致发光器件,器件结构及各层厚度为：ITO/CuPc(6 nm)/NPB(20 nm)/Alq₃(3 nm)/Alq₃：Rhodamine B(3 nm)/Alq₃(3 nm)/Alq₃：Rhodamine B(3 nm)/Alq₃(30 nm)/Liq(5 nm)/Al(30 nm)。研究发现Rhodamine B的掺杂浓度对该器件的发光亮度和发光效率有较大影响。当Rhodamine B的掺杂浓度为1.5 wt％时, 得到了最大电流效率1.526 cd·A-1,最大发光亮度1 309 cd·m-2的黄光有机电致发光器件。由器件的电致光谱曲线,可以看到在发光层之间存在着Alq₃向RhB传递能量的过程。由于量子阱的斯托克斯效应与RhB染料分子间的自极化作用,随着掺杂浓度的增加,λ_max出现明显红移。     

8-羟基喹啉铝在多孔铝中的发光研究

利用多孔铝非常高的孔隙率,将8-羟基喹啉铝(Alq3)镶嵌到多孔铝中,得到Alq3/多孔铝镶嵌膜,研究了不同条件下制备的多孔铝镶嵌膜的荧光光谱。实验表明,Alq3在多孔铝中的发光峰位在490 nm左右,比其在固态粉末状态蓝移了许多。Alq3/多孔铝镶嵌膜的发光特性与多孔铝中嵌入Alq3分子的数量及聚集程度有关。当分子数量较多、聚集程度较大时,发光增强,光谱峰位红移,但聚集程度太大时,易发生荧光猝灭现象。数量较多时,由于Alq3分子大多以范德瓦尔斯力结合,聚体较少,所以峰位移动幅度不大。实验中还发现,Alq3因为处在小孔中,光学性质稳定,荧光光谱带宽超过100 nm,比一般染料大得多,这使Alq3/多孔铝镶嵌膜有可能在固体可调谐激光器方面得到新的应用;同时也为探究Alq3/多孔铝镶嵌膜在电致发光器件中的发光特性奠定了基础,为将其进一步推向实用提供了实验依据。     

Dynamics of Förster Energy Transfer in Pyridium Salt-Doped Thin Films

Properties of photoluminescence and Förster energy transfer dynamics based on an organic pyridium salt trans-4-[p-(N-Hydroxyethyl-N-methylamino)Styryl]-N-methylpyridinium iodide (ASPI) and organic small molecule Alq3 in PMMA polymeric thin films are investigated by steady-state and time-resolved fluorescent spectra as well as theoretical calculation. The observation of reduced emission intensity and the fluorescent lifetime of Alq3 is demonstrated, while the ASPI emission gradually increases and is finally dominant in the PL spectra with increasing ASPI doping concentration. Such results show that there exists an efficient Förster energy transfer (FET) from Alq3 to ASPI due to the large spectral overlap between ASPI absorption and Alq3 emission. The difference between the theoretical FET efficiency and the experimental data is caused by the lower mobility of the Alq3 exciton in the MMA matrix.     

Violet-to-red photoluminescence of spiro-TAD organic films doped with different organic dyes

Photoluminescence (PL) and photoluminescence excitation (PLE) spectra of undoped spiro-TAD films and spiro-TAD films doped either by the organic dyes coumarin 7 or DCM as well as by both of these dyes simultaneously were investigated at different dye concentrations. A widened PL spectrum caused by doping was encountered and violet-to-red emission was obtained. It was established that excitation of the dyes is realized most efficiently through spiro-TAD. The overall integral PL intensity of the coumarin 7 doped films increased with dye concentration due to the suppression of nonradiative recombination in the film caused by a transfer of spiro-TAD excitation energy to the dye molecules. Mainly radiative energy transfer from semiconductor to dye molecules occurs in the case of DCM doping. No mutual influence on the luminescence of both dyes in the spiro-TAD film was observed and as a consequence, the PL band intensity of each dye can be adjusted separately.     

基于液体基质材料的有机电致发光器件的制备及性能分析

利用液体基质材料9-(2-ethylhexyl)carbazole(EHCz)掺杂有机染料分子5,6,11,12-tetraphenyl-nathacene(rubrene)制备了具有液体发光层的有机电致发光器件,其结构为:ITO/PEDOT:PSS/EH Cz:rubrene/Cs2CO3/ITO,PEDOT:PSS...     

Evolution of the unoccupied states in alkali metal-doped organic semiconductor

The evolution of the electronic structure, especially the unoccupied states, induced by alkali metal doping has been investigated with photoemission and inverse photoemission spectroscopy for organic semiconductors, such as copper-phthalocyanine (CuPc) and tris(8-hydroxyquinoline) aluminum (Alq). The n-type doping leads to a downward shift for the lowest unoccupied molecular orbital (LUMO) of the organic semiconductors, until the edge of the LUMO reaches the Fermi level. After that, the LUMO intensity decreases monotonically, while a gap state grows in the valence spectra, which gives direct evidence for the origin of the doping-induced gap state in organic molecules. The modification of the LUMO intensity, as well as that of the gap state, suggests the formation of multiply charged anions in heavily doped film.     

微量Mg掺杂ZnO薄膜的光致发光光谱和带隙变化机理研究

利用射频磁控溅射(RF-MS)法在450℃玻璃基底上制备了Mg掺杂量分别为0.81at%,2.43at%和4.05at%的ZnO薄膜,对其微观结构、室温光致发光光谱(PL)、光学和电学性质进行了研究.结果发现,微量Mg掺杂ZnO薄膜晶体具有六方纤锌矿结构并保持高结晶质量;掺杂0.81at%和2.43at%Mg的ZnO薄膜室温PL谱中近带边发射(NBE)峰的短波方向出现了高能发射带与NBE峰同时存在;随着Mg掺杂量增加至4.05at%,这个高能发射带逐步将NBE峰掩盖.推测在Mg掺杂ZnO薄膜中,Mg2+替代Zn2+附近核外电子的能量增大并产生了一个高能级.而未被Mg2+替代的Zn2+周围的核外电子能量状态不变,带间能级依然存在,随着Mg掺杂量的增加处于高能级的电子数目逐步增加并占绝对优势.因此,ZnO薄膜随着Mg掺杂量增加薄膜禁带宽度增大,这是由于Mg掺杂后周围电子能量增大与Burstein-Moss效应共同作用的结果.另外,薄膜在可见光区域的平均透射率均大于85%,随着Mg掺杂量的增加,薄膜禁带宽度增大并在3.36—3.52eV内变化;Mg掺杂量为0.81at%,2.43at%和4.05at%时,薄膜电阻率分别为2.2×10-3,3.4×10-3和8.1×10-3Ω.cm.     

有机多层量子阱结构的光致发光特性的研究

采用多源高真空有机分子束沉积系统(OMBDs),将两种有机小分子材料PBD和Alq₃以交替生长的方式,制备了不同厚度的PBD/Alq₃有机多层量子阱结构(OMQWs), 并利用电化学循环伏安法和光吸收分别测定了PBD和Alq₃的最低空分子轨道(LUMO)和最高占据分子轨道(HOMO)。该结构类似于无机半导体中的Ⅰ型量子阱结构,PBD层作为势垒层,Alq3层作为势阱层和发光层,并进行了小角X射线衍射(XRD)的测量。利用荧光光谱研究了OMQWs光致发光(PL)特性,得到随着阱层厚度的降低,光致发光的峰位将蓝移;同时随垒层厚度的减小,PBD的发光峰逐渐消失。利用量子阱结构可以使PBD的能量有效的传递给Alq₃,从而增强Alq₃的发光。     

2018年5期 电子期刊

研究了不同Mn/Pb量比的Mn掺杂CsPbCl₃（Mn：CsPbCl₃）钙钛矿量子点的发光性质。Mn/Pb的量比增加引起的Mn²⁺发光峰的红移,被认为是来源于高浓度Mn²⁺掺杂下的Mn²⁺-Mn²⁺对。进一步研究了Mn：CsPbCl₃量子点的发光效率与Mn/Pb的量比之间的关系,发现随着量比达到5：1时,其发光效率明显下降。这种发光效率下降是由于Mn掺杂浓度引起的发光猝灭。Mn：CsPbCl₃量子点的变温发光光谱证实,随着温度的升高,Mn离子发光峰蓝移,线宽加宽,但其发光强度明显增加。     

Ir(Fppy)_3掺杂PVK体系发光特性的研究

对蓝色磷光材料Ir(Fppy)3不同浓度掺杂PVK薄膜的光致发光(PL)和电致发光(EL)特性进行了研究。并制备了结构为ITO/PEDOT:PSS/PVK:Ir(Fppy)3/BCP/Alq3/LiF/Al的蓝色磷光有机电致发光器件。实验结果发现,磷光材料掺杂浓度不同,器件发光特性不同。当Ir(Fppy)3掺杂浓度比较低时,EL光谱中可以观察到PVK较弱的发光;当Ir(Fppy)3掺杂浓度较高时,会发生浓度猝灭;当Ir(Fppy)3掺杂浓度比较适中时,EL光谱中观察不到PVK的发光,只有Ir(Fppy)3的发光。通过I-V-L特性的比较,当掺杂浓度为4%时,器件的光电特性最好。     

Energy transfer dynamics between Alq3 and CdTeS/ZnS core shell nanocrystals

The photoluminescence (PL) properties of the guest-host films, using CdTeS/ZnS core shell quantum dots (QDs) as the guest and organic small-molecule material Alq₃ as the host, are studied by steady-state and time-resolved PL spectroscopy. Both the relative intensity and the PL lifetime are intensively dependent on the weight ratio of Alq₃ and CdTeS/ZnS QDs. The detailed analysis provides clear evidence for a Förster energy transfer from Alq₃ host to QDs guest, based on the nonradiative resonant transfer mechanism. The results are relevant to the application of hybrid organic/inorganic systems to OLEDs.     

Property enhancement of transparent conducting zinc oxide thin films—Effect of simultaneous (Sn+F) doping

Undoped and simultaneously (Sn+F) doped ZnO thin films were fabricated using a simplified spray pyrolysis technique and the effects of Sn doping level on their electrical, structural, optical and surface morphological properties were studied. The XRD patterns confirmed the hexagonal wurtzite structure of ZnO. The minimum electrical resistivity of 0.45×10⁻² Ω cm was obtained for ZnO films having Sn+F doping levels of 8+20 at%. All the films exhibited average optical transmittance of 85% in the visible region, suitable for transparent electrode applications. The overall quality of the fabricated films was confirmed from photoluminescence (PL) studies. The PL and surface morphological studies along with the elemental analysis showed the increase of Sn diffusion into the ZnO lattice which was consistent with the concentration of Sn in the starting solution. The results of the analysis of physical properties of simultaneously doped ZnO films proved that these films might be considered as promising candidates for solar cells and other opto-electronic applications.     

Influence of the grain boundary barrier height on the electrical properties of Gallium doped ZnO thin films

The pulsed laser deposition (PLD) technique is used to deposit Gallium doped zinc oxide (GZO) thin films on glass substrates at 250 with different Gallium (Ga) doping concentration of 0, 1.0, 3.0 and 5.0%. The influence of Ga doping concentration on structure, chemical atomic compositions, electrical and optical properties was investigated by XRD, XPS, Hall measurement and UV spectrophotometer, respectively. The relationship between electrical properties and Ga doping concentration was clarified by analyzing the chemical element compositions and the chemical states on the GZO films. It is found that the carrier concentrations and oxygen vacancies in the GZO films increase with increasing Ga doping concentration. The lowest resistivity (3.63 × 10⁻⁴ Ω cm) and barrier height of grain boundaries (14 mV) were obtained with 3% Ga doping. In particular, we suppose the band gap of 5% Ga doping sample larger than that of 3% Ga doping sample is due to the quantum size effect from the amorphous structure rather than Moss-Burstein shift.     

Optical permittivity,thermo-optical and electrical properties of nickel oxide nanostructures with heavy cupper doping

In this research, physical properties of nickel oxide nano-structured layers doped with various amount of Cu atoms (20–60 at.%) is studied using spray pyrolysis method on the glass substrate. The FESEM images show formations of nanostructures of about 20–60 nm and the XRD patterns show layers have a polycrystalline cubic structure nature with (111) as the preferred direction that its intensity reduces as the doping density increases. Analyzing transmittance UV. Vis spectra shows the variations of optical band gap of the samples are due to occurrence of doping atoms and quantum confined effects. Optical permittivity of different doped films have been compared using new numerical method and show the prominent effect of doping percent to real and imaginary parts of electrical permittivity. Also Hall effect results shows that Cu atoms substituted by Ni atoms sites play as acceptor atoms in the crystalline lattice. Finally, thermo-optical properties of the films have been studied using Nd–YAG laser illumination.     

Ir(ppy)3掺杂PVK体系发光特性的研究

对常温下磷光染料Ir(ppy)3掺杂PVK薄膜的光致发光(PL)和电致发光(EL)特性进行了研究。器件结构为ITO/PEDOT:PSS/PVK:Ir(ppy)3/BCP/Alq3/Al。实验发现随磷光材料掺杂浓度的不同,器件的发光性能发生变化。当浓度适宜时,主体材料PVK的发光很弱,主要为Ir(ppy)3的磷光发射。通过L-I-V特性曲线的比较,掺杂浓度为5%的光电性能最好,说明器件在掺杂浓度为5%时效果最佳。     

铕配合物Eu( UVA)3Phen与PVK掺杂体系发光特性的研究

将一种新型稀土铕配合物Eu(UVA)3 Phen作为掺杂剂与基质PVK按不同质量比进行掺杂,对混合薄膜的光致发光(PL)和电致发光(EL)特性进行了研究.实验结果表明,共掺杂体系中存在从PVK到Eu(UVA)3 Phen的F(o)rster能量传递.通过优化主客体材料的配比浓度,当掺杂浓度为4％时,得到了色纯度较好地红...     

Ir(PPY)3掺杂PVK的电致发光机理

近几年来发展起来的电致磷光(electrophosphorescence)是有机发光二极管(OLED)研究的新生长点。对电致磷光发光机理的研究随即得到了人们普遍的关注。比较了不同正向偏压条件下Ir(PPY)₃掺杂聚乙烯基咔唑(PVK)的光致发光(PL)和电致发光(EL)光谱。研究结果显示在电场和注入电流的共同作用下,PL光谱中基质PVK发光的相对强度并没有发生显著的变化。电场或注入载流子不会影响PVK向Ir(PPY)₃的能量传递。磷光掺杂聚合物EL主要是由于载流子在掺杂磷光分子上的直接复合,而不是由基质向磷光掺杂分子的能量传递。     

Optical properties of Si-doped InAs/InP quantum dots

InAs quantum dots (QDs) were grown on InP substrates by low pressure-metalorganic chemical vapor deposition. Disilane (Si₂H₆) was used as an n-type dopant. The positions of Si doping were varied: buffer layer, capping layer, modulation doping, and QD itself. Surface treatment of InP by Si₂H₆ was also performed to see the effect of Si on InAs QD. Photoluminescence (PL) and atomic force microscopy (AFM) were used to characterize optical and structural properties of QDs, respectively. It was found that the PL peak positions varied from 0.73 to 0.88 eV with the position of Si doping. PL peak blue shift in modulation doped sample was explained in terms of state filling effect. It was found that Si doping at QD itself was the most effective way to obtain the strongest integrated PL intensity without degrading the QD size distribution.