一种平行栅碳纳米管阵列阴极的场发射特性研究

建立一种平行栅碳纳米管阵列阴极,利用悬浮球模型和镜像电荷法进行计算,给出碳纳米管顶端表面电场与电场增强因子的解析式. 在此基础上,进一步分析器件各类参数以及接触电阻对阴极电子发射性能的影响. 分析表明,碳纳米管间距大约为2倍碳纳米管高度时阵列阴极的分布密度最佳,靠边缘部位的碳纳米管发射电子能力比其中心部位的大;除碳纳米管的长径比之外,栅极宽度和栅极间距也对电场增强因子有一定作用;接触电阻的存在大幅度降低碳纳米管顶端表面电场与发射电流,而接触电阻高于800 kΩ时,器件对阳极驱动电压的要求更高. 关键词： 平行栅碳纳米管阵列 悬浮球 场增强因子 接触电阻     

Effect of optical phonons scattering on electronic current in metallic carbon nanotubes

The effect of optical phonons scattering on electronic current has been studied in metallic carbon nanotubes. The current has been calculated self-consistently by total voltage equation and the heat transport equation. The total voltage equation consists of three terms, optical phonons collision term, acoustic phonon scattering term, and contact resistance one. Including LO, A₁, and E₁(2) phonons in collision term, we can reproduce the experimental I-V curves displaying negative differential conductance. Furthermore, one conclusion is made that the more optical phonons are scattered by electron, the lower current is in metallic carbon nanotubes. By comparing the current under different conditions, we can make another conclusion that there should be nonequilibrium optical phonons under high bias in spite of whether the metallic nanotube is suspended or not. This result agrees well with the others [M. Lazzeri, F. Mauri, Phys. Rev. B 73 (2006) 165419]. Based on these results, we do not only explain the experiment, but also propose to design a heat-controlling electronic transistor with metallic carbon nanotubes as its channel, in which the electronic current can be controlled by optical phonons.     

Optimization of the parameters of a carbon nanotube-based field-emission cathode

A procedure for optimizing a field-emission cathode based on carbon nanotubes (CNTs) is developed. An array of identical equidistant vertical CNTs is considered. The optimization procedure takes into account the effect of screening of an electric field by neighboring nanotubes by solving a Laplace equation and the thermal instability of nanotubes, which limits the emission current density of a nanotube, by solving a heat conduction equation. The relation between the emission current and the applied voltage is described by the Fowler-Nordheim relationship containing the CNT tip temperature as a parameter. Upon optimization, the optimum distance between CNTs that ensures the maximum emission current density is calculated. The calculation results demonstrate that this parameter depends substantially on both the applied voltage and the nanotube geometry. These dependences are weakly sensitive to the choice of the transport coefficients (thermal conductivity, electrical conductivity) of nanotubes.     

碳纳米管网络导电特征的导电型原子力显微镜研究

利用导电型原子力显微镜对大范围碳纳米管（CNT）网络的导电性能进行成像观察.研究发现：在几十微米的成像范围内,每根CNT本身的电阻远小于CNT之间的接触电阻,以致于在电压偏置的网络中不同的CNT呈现电位不同的等位体;CNT的导电性能虽不因与其他CNT的交叠接触而改变,但是如果缠绕成束,则半导体性CNT趋于呈现金属性CNT的导电特征. 关键词： 导电型原子力显微镜 碳纳米管网络 碳管纳米电导     

Four-point resistance of individual single-wall carbon nanotubes

We have studied the resistance of single-wall carbon nanotubes measured in a four-point configuration with noninvasive voltage electrodes. The voltage drop is detected using multiwalled carbon nanotubes while the current is injected through nanofabricated Au electrodes. The resistance at room temperature is shown to be linear with the length as expected for a classical resistor. This changes at cryogenic temperature; the four-point resistance then depends on the resistance at the Au-tube interfaces and can even become negative due to quantum-interference effects.     

Modification of the structure and percolation of current in an array of single-walled carbon nanotubes

Percolation and electrical instability processes in an array of single-walled carbon nanotubes have been studied experimentally. The experiment is based on comparison between the dynamics of nanosecond percolation under the active and passive actions of the electric field in coils/granules of single-walled carbon nanotubes. Regularities of the mechanism based on the similarity laws for nanocoils are revealed.     

A flexible paper transistor made with aligned single-walled carbon nanotube bonded cellulose composite

We report a flexible paper transistor made with single-walled carbon nanotubes covalently bonded cellulose (SCBC) composite without any additional semiconducting layer. Single-walled carbon nanotubes are covalently grafted to cellulose fibrils in a regenerated cellulose film to form the SCBC composite followed by a mechanical stretching process. The SCBC transistor shows a remarkable current–voltage characteristic depending on the stretching ratio. We found that the alignment of covalently bonded carbon nanotube plays a role that governs the electrical channel behavior of the SCBC composite.     

碳湿敏膜的非线性感湿特性和导电机理

采用羟乙基纤维素（HEC）和导电炭黑并添加山梨醇增湿剂制备碳湿敏膜,研究了膜在偏离结露区的非线性感湿特性和导电机理.扫描电镜观测到,膜中炭黑粒子形成网链状的空间导电结构;2%炭黑含量使膜的导电通路处于渗流区,膜电阻在80%RH附近对湿度有较强的非线性特性.分析I-V曲线认为,是导电网链中炭黑粒子的间距使膜电阻对湿度变化和测量电压的变化都非常敏感,非线性感湿特性与导电机理密切相关.复阻抗谱表明,碳湿敏样品在33%RH时只出现与炭黑体电阻有关的半圆弧,在80%RH时出现与炭黑粒界电 关键词： 碳湿敏膜 逾渗阈值 I-V特性')" href="#">I-V特性 复阻抗谱     

Intrinsic memory characteristic of polycrystalline ZnTe film originating from Mott variable range hopping conduction

The resistive switching characteristics of Au/ZnTe/ITO structure with polycrystalline ZnTe film as resistive switching layer is investigated. Macroscopically, 100 bipolar switching cycles under the direct current (dc) voltages were carried out and the conduction states can retain for several hours. Microscopically, reading and writing operations can be achieved on ZnTe film with Au top electrode replaced by conductive Atomic Force Microscopy (c-AFM) tip. The I–V characteristic in low resistance state (LRS) is linear in the whole range of voltage. The I–V characteristic in high resistance state (HRS) is linear in the low voltage while it obeys Schottky emission in the high voltage, and Schottky barrier height is symmetric in the positive and negative voltage. During linear I–V characteristic voltage range, the electrons transport between adjacent point defects via Mott variable range hopping. The higher hopping distance and higher activation energy in HRS contribute to the higher resistance value in HRS compared with LRS. Impedance spectroscopy in HRS and LRS both behave as a semicircle, which accords with the semiconductor-like characteristic of conductive point defects. Photoluminescence (PL) spectroscopy indicates the decisive role of deep level defects in conduction. This study confirms the intrinsic resistive switching characteristic of ZnTe film and provides a new choice for intrinsic non-oxides material in nonvolatile memory application.     

Effect of Carbon on the Electrical Properties of Copper Oxide-Based Bulk Composites

The effect of carbon filler on the electrical resistance and the thermopower of copper oxide-based composites produced by ceramic technology by hot pressing has been studied. It is found that the dependences of the electrical resistivity on the filler concentration are characteristic by S-like curves that are typical of percolation systems; in this case, the resistivity decreases more substantially as the carbon content increases as compared to the decrease in thermopower value, which is accompanied by the existence of the maximum of the factor of thermoelectric power near the percolation threshold. The studies of the temperature dependences of the resistivity and the thermopower at low temperatures show that, in the range 240–300 K, the predominant mechanism of the electrotransfer of all the composites under study is the hopping mechanism. At temperatures lower than 240 K, the composites with a nanocrystalline CuO matrix have a hopping conductivity with a variable hopping distance over localized states of the matrix near the Fermi level, which is related to the conductivity over intergrain CuO boundaries. A schematic model of the band structure of nanocrystalline CuO with carbon filler is proposed on the base of the analysis of the found experimental regularities of the electrotransfer.     

Simple and accurate model for voltage-dependent resistance of metallic carbon nanotube interconnects: An ab initio study

In this work, development of a voltage dependent resistance model for metallic carbon nanotubes is aimed. Firstly, the resistance of metallic carbon nanotube interconnects are obtained from ab initio simulations and then the voltage dependence of the resistance is modeled through regression. Self-consistent non-equilibrium Green's function formalism combined with density functional theory is used for calculating the voltage dependent resistance of metallic carbon nanotubes. It is shown that voltage dependent resistances of carbon nanotubes can be accurately modeled as a polynomial function which enables rapid integration of carbon nanotube interconnect models into electronic design automation tools.     

Electrode surface treatment and electrochemical impedance spectroscopy study on carbon/carbon supercapacitors

Power improvement in supercapacitors is mainly related to lowering the internal impedance. The real part of the impedance at a given frequency is called ESR (equivalent series resistance). Several contributions are included in the ESR: the electrolyte resistance (including the separator), the active material resistance (with both ionic and electronic parts) and the active material/current collector interface resistance. The first two contributions have been intensively described and studied by many authors. The first part of this paper is focused on the use of surface treatments as a way to decrease the active material/current collector impedance. Al current collector foils have been treated following a two-step procedure: electrochemical etching and sol-gel coating by a highly-covering, conducting carbonaceous material. It aims to increase the Al foil/active material surface contact leading to lower resistance. In a second part, carbon-carbon supercapacitor impedance is discussed in term of complex capacitance and complex power from electrochemical impedance spectroscopy data. This representation permits extraction of a relaxation time constant that provides important information on supercapacitor behaviour. The influence of carbon nanotubes addition on electrochemical performance of carbon/carbon supercapacitors has also been studied by electrochemical impedance spectroscopy. PACS 82.45.Yz; 81.16.-c     

基于扫描电子显微镜的碳纳米管拾取操作方法研究

碳纳米管场效应管是未来纳米器件的发展方向,而制造纳米器件的前提是拾取碳纳米管,基于扫描电子显微镜(SEM)的微纳机器人操作系统能够实现碳纳米管拾取操作.本文建立拾取操作中碳纳米管与原子力显微镜(AFM)探针间范德瓦耳斯力力学模型,不同接触状态下范德瓦耳斯力越大越有利于拾取碳纳米管.在SEM视觉反馈图像中建立相对坐标系,首先提出倾角变值方法检测碳纳米管与AFM探针的接触状态,然后运用动态差值方法识别碳纳米管与AFM探针空间位姿并校正碳纳米管位姿,最后自下而上拾取碳纳米管.实验结果表明:拟合直线倾角变值较大时碳纳米管与AFM探针发生接触,动态差值变化为零时碳纳米管与AFM探针为空间线接触,在完全线接触模型下选择合适的接触角度、接触长度和拾取速度能够成功拾取碳纳米管.     

Nonmonotonic behavior of resistance in a superconductor-Luttinger liquid junction

Transport through a superconductor-Luttinger liquid junction is considered. When the interaction in the Luttinger liquid is repulsive, the resistance of the junction with a sufficiently clean interface shows nonmonotonic temperature or voltage dependence due to the competition between the superconductivity and the repulsive interaction. The result is discussed in connection with recent experiments on single-wall carbon nanotubes in contact with superconducting leads.     

Description of the degree of reinforcement of polymer/carbon nanotube nanocomposites in the framework of percolation models

A radically new percolation model for describing the extremal dependence of the degree of reinforcement of polymer/carbon nanotube nanocomposites on the nanofiller content has been proposed. It has been shown that, for this nanofiller, the percolation threshold almost coincides with the aggregation threshold on the concentration scale. From the structural point of view, the extremum of this dependence is caused by the change in the type of the reinforcing component (from interphase regions to the skeleton of carbon nanotubes). From the mathematical point of view, the behavior of the degree of reinforcement is described by the general percolation relationship with replacement of the critical exponents near the percolation threshold. Neither the functionalization of the nanofiller nor the preliminary ultrasound treatment qualitatively change the dependence under study.     

Melt mixing of polycarbonate/multi-wall carbon nanotube composites

—Composites of polycarbonate (PC) with multi-wall carbon nanotubes (MWNT) of different concentrations are prepared by diluting a PC based masterbatch containing 15 wt% MWNT using melt mixing in a DACA-Micro Compounder (4 g scale). Electrical resistivity measurements indicate that the percolation of MWNT is reached between 1 and 1.5 wt%. In addition, melt rheology was applied as another sensitive method to detect the percolation of the nanotubes. Atomic Force Microscopy and visual observations of the composite dispersions in a PC-solvent were used to characterise the state of MWNT dispersion. Differential Scanning Calorimetry and Dynamic Mechanical Analysis were applied to detect changes in the glass transition temperature of PC as a result of processing and of MWNT interactions with the PC matrix including the state of dispersion. In addition, DMA confirmed the reinforcement effect of the nanotubes. The results show that the nanotube incorporation also influences the processing behaviour. Due to the enhancement in melt viscosity by adding nanotubes and the enhanced shear forces, the molecular weight of the PC in the composites is reduced as compared to PC extruded under the same conditions. This effect leads to changes in the glass transition temperature and modulus which counteracts the effects originating from the nanotube-polymer interaction.     

Influence of contact resistance on the percolation interval in disordered metal-insulator macrosystems

The dependence of the resistivity of a paraffin-conductor macrosystem on the conducting phase concentration has been experimentally studied. A model of conduction in systems with different contact resistances in terms of the percolation theory is suggested, and an indirect characteristic of contact resistance is introduced.     

Electric field induced by vortex transport in percolation superconductors

The influence of fractal normal phase clusters on the electric field induced by the flow and creep of the magnetic flux in percolation superconductors has been considered. The current–voltage characteristics of such superconductors with allowance for the influence of the fractal dimension of cluster boundaries and the pinning barrier height have been obtained. The vortex dynamics in percolation superconductors with a fractal cluster structure in a viscous flow of the magnetic flux, the Anderson–Kim creep, and the collective flux creep has been analyzed. It has been discovered that the fractality of normal phase clusters reduces the electric field arising in the initial stage of the resistive transition.     

Superconductivity in ropes of single-walled carbon nanotubes

We report measurements on ropes of single-walled carbon nanotubes (SWNT) in low-resistance contact to nonsuperconducting (normal) metallic pads, at low voltage and at temperatures down to 70 mK. In one sample, we find a 2 orders of magnitude resistance drop below 0.55 K, which is destroyed by a magnetic field of the order of 1 T, or by a dc current greater than 2.5 microA. These features strongly suggest the existence of superconductivity in ropes of SWNT.