一种新型高灵敏度光学微环湿度传感器

提出了以聚酰亚胺（PI）为感湿材料的三耦合点单微环新型湿度传感器。外界湿度变化使得聚酰亚胺SOI微环谐振特性发生变化,最终通过谐振波长的漂移量确定湿度值。讨论了不同部位感湿时系统的传感特性,并且选择了最佳湿敏元件。数值模拟结果表明：与传统的单微环传感器相比,新型传感器具有较高灵敏度和测量范围,Through端口的自由频谱范围可提高3倍。三耦合点单微环谐振器整体结构可作为最佳湿敏元件,该传感器在10%RH~80%RH相对湿度范围内,灵敏度可达到0.98 nm/%RH,该结构为制备高灵敏度可集成微型湿度传感器件提供了一定的理论依据。     

硼掺杂对四面体非晶碳膜电导性能的影响

以单质硼和高纯石墨的混合粉末压制成型的靶材作为靶源,采用过滤阴极真空电弧技术制备不同硼含量的掺硼四面体非晶碳膜.分别采用四探针法、阻抗分析仪和电化学界面对薄膜的变温电导率、I-V特性和C-V特性进行了测试和研究.实验结果表明,当B含量由0增加至6.04 at%时,薄膜的室温电导率先逐渐增大而后逐渐减小,相应薄膜的电导激活能先逐渐减小而后逐渐增大,并在2.13 at%时分别出现最大和最小值1.42×10^-7S/cm和0.1eV.此外,掺硼四面体非晶碳/n型硅异质结的I-V曲线表现出典型的整流特性,表明p-n结二极管已经形成,且结两端的掺杂能级在空间上连续统一. 关键词： 四面体非晶碳 电导率 I-V曲线')" href="#">I-V曲线 C-V曲线')" href="#">C-V曲线     

ZnO压敏陶瓷电导研究的新方法

在-180?℃—100?℃温度范围内研究了ZnO-Bi₂O₃二元、ZnO-Bi₂O₃-MnO三元以及商用ZnO压敏陶瓷的I-V特性.研究发现：二元试样电导由散射电导串联构成;三元试样电导由热电子发射电导混联构成;商用试样电导由热电子发射电导和隧道效应电导并联构成.对整个电流范围内的电导拟合表明：通过同一温度下电导分量同电流的关系,可以计算出该部分电导对应的非线性指数.在商用试样中,隧道电流产生的非线性指数为33,与实测值接近;该隧穿分量在小电流区也存在,且在低温下表现地更为明显. 关键词： ZnO压敏陶瓷 I-V特性')" href="#">I-V特性 导电机理     

点接触金属/Pr$lt;sub$gt;0.7$lt;/sub$gt;Ca$lt;sub$gt;0.3$lt;/sub$gt;MnO$lt;sub$gt;3$lt;/sub$gt;/Pt结构稳定的低电流电阻开关特性

利用自主开发的导电原子力显微镜控制Pt,W探针构成点接触金属/Pr_0.7Ca_0.3MnO₃（PCMO）/Pt三明治结构,对其电流-电压（I-V）及脉冲诱导电阻开关（EPIR）特性进行了研究.研究发现,在10 nA限流下两种电极对应结构的I-V都表现出相当稳定的双极性电阻开关特性,以及大于100的电阻开关比.进一步测试发现,点接触W/PCMO/Pt器件具有在10 nA限流下稳定的EPIR特性以及100 pA限流下重复的双极性电阻开关特性.此电流比已报道的电流低3个数量级,表明此结构在低功耗存储器件方面的潜在应用.通过对比样品不同位置、不同限流、不同接触面积点接触Pt/PCMO/Pt的I-V回滞特性,把点接触器件在低电流下稳定、显著的电阻开关效应归结于小的器件面积导致强的局域电场加强了O离子迁移效应. 关键词： 脉冲诱导电阻开关 电场下氧离子迁移 电阻开关     

复合型导电硅橡胶的电阻温度特性研究

研究了复合型导电硅橡胶的电阻温度特性,分析了升温过程中导电硅橡胶电阻特性的详细变化过程.研究了导电粒子含量对导电硅橡胶电阻温度特性的影响,测量了在不同热处理温度下电阻率的变化及加力时电阻的弛豫时间.分析了热处理对电阻特性影响的机理. 关键词：     

多壁碳纳米管膜湿敏特性的研究

研究了多壁碳纳米管(MWNTs)薄膜的湿敏特性，实验所用的多壁碳纳米管是用热灯丝化学气相沉积法(CVD)合成的.分别对未修饰和修饰的多壁碳纳米管膜温度和湿度特性进行研究后发现，修饰的多壁碳纳米管对温度和湿度非常敏感，且对湿度的响应时间和恢复时间短，重复性好.而未修饰的多壁碳纳米管对温度和湿度不太敏感.对修饰多壁碳纳米管的湿敏特性进行了理论分析，给出了其理论表示式. 关键词： 多壁碳纳米管 化学修饰 湿敏特性 物理吸附     

光纤SPR湿敏传感器及其共振光谱特性研究

提出并研制了基于光纤SPR传感探针的新型湿敏传感器。首先研究了光纤SPR传感探针对环境湿度变化的敏感特性,在此基础上提出在光纤SPR传感探针表面增覆不同厚度且具有水分子吸附功能的PVA薄膜来实现环境相对湿度的监测。研究结果表明,增覆双层PVA薄膜的光纤SPR传感探针在高湿区具有较好监测效果,其共振强度对应的相对湿度测量灵敏度达到1.59%/%RH,较光纤SPR探针呈现显著提高。而增覆单层PVA薄膜的光纤SPR传感探针在高湿区共振波长对应的相对湿度监测灵敏度达到2.411nm/%RH。此外所提出的新型光纤SPR湿敏探针在PVA薄膜失效后经过特殊工艺处理仍可重复镀膜使用。     

电阻型高分子湿敏元件的光辐射改性研究

电阻型高分子湿敏元件在氦氖激光、太阳光、紫外光辐照一定的时间后，用在不同湿度下测量辐照前后的电阻值来分析元件性能的变化，在较长的时间内跟踪测量来观察其长期稳定性。结果表明，湿敏元件在氦氖激光照射一定时间后，其感湿特征量的线性和长期稳定性匀变好。     

ZnO纳米线场效应管的制备及I-V特性研究

采用静电探针和原子力探针技术,将化学气相沉积工艺制备的,长度为30—200 μm,直径80—750 nm的单根半导体ZnO纳米线搭接在Au,Zn,Al不同功函的金属隔离沟道两端,构建出了最基本的ZnO纳米线绝缘栅场效应管. 研究了沟道类型、纳米线直径、退火温度和外加栅压对ZnO纳米线场效应管I-V特性的影响. 利用半导体与金属材料的肖特基接触、欧姆接触的产生机理及电子输运理论,对结果进行了分析和讨论. 关键词： ZnO纳米线 场效应管 I-V特性')" href="#">I-V特性     

硅衬底的SrTiO3淀积膜的湿敏特性与机理研究

对无定形多孔SrTiO₃膜电导率随相对湿度的变化进行了理论模型分析.该模型也适用于其他多孔半导体陶瓷材料.实验样品用氩离子束镀膜技术在SiO₂/Si衬底上淀积SrTiO₃膜并制成平面型电阻结构.结果表明，在室温下，当相对湿度从12%变化至53%时，电流缓慢下降；而当相对湿度从53%变化至92%时，电流又显著上升，即在高湿度条件下具有良好的湿敏特性.电流及其在高湿条件下的上升率随测试频率而增大.吸附响应时间明显长于脱附时间. 关键词：     

Graphene oxide thin film coated quartz crystal microbalance for humidity detection

In this paper, we demonstrated that chemically derived graphene oxide (GO) thin film as a humidity sensitive coating deposited on quartz crystal microbalances (QCMs) for humidity detection. By exposing GO thin film coated QCMs to various relative humidity (RH) environments at room temperature, the humidity sensing characteristics of the QCMs such as sensitivity and linearity, response and recovery, humidity hysteresis were investigated. The experiment results show that GO thin film coated QCMs exhibit an excellent humidity sensing performance. Moreover, the possible humidity sensing mechanism of GO thin film coated QCMs was also investigated by monitoring the crystal's motional resistance change. It is suggested that the frequency response of the QCMs is dependent on water molecules adsorbed/desorbed masses on GO thin film in the low RH range, and on both water molecules adsorbed/desorbed masses on GO thin film and variations in interlayer expansion stress of GO thin film derived from swelling effect in the high RH range.     

Electrical switching in metallic carbon nanotubes

We present first-principles calculations of quantum transport which show that the resistance of metallic carbon nanotubes can be changed dramatically with homogeneous transverse electric fields if the nanotubes have impurities or defects. The change of the resistance is predicted to range over more than 2 orders of magnitude with experimentally attainable electric fields. This novel property has its origin that backscattering of conduction electrons by impurities or defects in the nanotubes is strongly dependent on the strength and/or direction of the applied electric fields. We expect this property to open a path to new device applications of metallic carbon nanotubes.     

接触电阻对碳纳米管场发射的影响

基于改进的悬浮球模型,计算了碳纳米管和衬底间的接触电阻存在时碳纳米管顶端的局域电场, 并结合Fowler-Nordheim (F-N)场发射规律研究了接触电阻对碳纳米管场发射的影响.研究表明,接触电阻的存在,在高电场区域接触电阻抑制了碳纳米管的电子场发射,导致在高电场区域出现电流饱和及FN直线偏折现象.其原因可归结为接触电阻使得在碳纳米管顶端的局域电场相对于没有接触电阻时相对地减少. 关键词： 碳纳米管 场发射 接触电阻 电流饱和     

Synthesis,characterization and mechanical properties of nylon–silver composite nanofibers prepared by electrospinning

Silver (Ag) nanoparticles (∼3 nm) were synthesized using silver nitrate as the starting precursor, ethylene glycol as solvent and poly (N-vinylpyrrolidone) (PVP) introduced as a capping agent. These nano-Ag particles were reinforced in nylon matrix by electrospinning of nylon-6/Ag solution in 2,2,2-trifluoroethanol and composite nanofibrous membranes were synthesized. The effects of solution concentration and relative humidity (RH) on the resultant fibrous membranes were studied. Scanning electron microscopy and Transmission electron microscopy was used to study the size and morphology of the fibers. It was observed that concentration and RH could be used to modulate the fiber diameter. Tensile test was used to evaluate the mechanical property of these electrospun composite membranes. The composite membranes showed higher strength (approx. 2–3 times increase in strength) compare to as synthesized nylon fibers.     

对碳纳米管阵列的场发射电场增强因子以及最佳阵列密度的研究

研究了外电场、碳纳米管自身线度、尤其管的阵列密度对碳纳米管的场发射性能的影响,从理论上深入探索碳纳米管阵列的电场增强因子并提出改善其场发射电子性能的有效途径.研究结果表明,碳纳米管阵列的电场增强因子的数量级一般为102—103,并对任何长径比的碳纳米管阵列,都对应着一个最佳阵列密度,当碳纳米管阵列密度取此最佳密度值时,其电场增强因子明显提高.这里的理论研究对弄清碳纳米管的场发射机理及实验合成高发射性能的碳纳米管阵列有一定的意义 关键词： 碳纳米管阵列 最佳阵列密度 电场增强因子 长径比     

Investigation of Carbon Black Network in Natural Rubber with Different Bound Rubber Contents

A new method was applied to modify the surface activity of virginal carbon black (VCB). LA‐57, one kind of hindered amine light stabilizer, was adsorbed onto the carbon black surface through a strong shear force induced by the screws of a HAAKE internal mixer. The modified carbon black (MCB) was characterized by FT‐IR and thermogravimetric analysis (TGA). The bound rubber content of the natural rubber (NR) compounded with MCB and VCB varied with the fraction of LA‐57 on the MCB surface. The nonlinear effect at small strains, generally referred as the Payne effect, was investigated in the rubber compounds based on the different bound rubber contents. The NR compound containing the lowest bound rubber content had an obvious Payne effect. Based on the bound rubber content, the types of filler network varied from direct contact mode to the joint rubber shell mechanism.     

Carbon-coated Non-magnetic Iron Oxide Particles for the Substrate of Multi-layered Magnetic Recording Media

Non-magnetic particles with finer size (less than 200 nm), higher dispersibility, higher blackness and lower electrical resistance are required to produce better multi-layered magnetic tape media which have non-magnetic substrate using non-magnetic sub-layer materials. A special method to prepare acicular hematite particles, whose cross-sectional diameter is about 150 nm, coated with carbon black using a surface modification agent is reported in this paper. Transmission electron microscopy photographs of carbon-coated hematite particles indicate that all of the carbon black is firmly bound to the surface in a distinct layer. The thickness of carbon-coating layer was about 1 to 2 nm if 15% by weight of carbon black is coated onto the particle surface.Non-magnetic substrates for multi-layered magnetic recording media prepared using the carbon-coated particles exhibit improvements in both light transparency and electrical resistance. A decrease in transparency of about 30% as well as a reduction in the electrical resistance of about 1.5 orders of magnitude relative to conventionally prepared substrates was achieved. The surface smoothness and the viscosity were also improved because the dispersibility of these particles in non-magnetic lacquer became better than that of the physical mixture of uncoated hematite particles and carbon black.     

工业SO2及碳黑颗粒紫外成像遥感监测技术

为了准确有效监测工业烟囱排放,基于SO2及碳黑颗粒物的光学特性,设计并研制出一套双通道紫外成像遥感监测系统.该成像系统的两个光谱通道的中心波长分别定于310 nm和330 nm,利用两个通道的光学厚度之差反演SO2浓度图像,颗粒物浓度图像由330 nm通道获取,根据浓度图像结合光流法获取烟羽运动速度,进而计算得出SO2和碳黑颗粒物的排放速率.结果表明,该工业烟囱的SO2及碳黑颗粒物排放速率分别为72.48±3.16 kg/h和6.33±1.18 kg/h.实验采用紫外相机同时对工业烟囱排放的SO2及碳黑颗粒物进行监测,实验表明双通道紫外成像遥感监测兼具高时间分辨率与高空间分辨率,测量结果准确直观,在工业废气污染、船舶尾气污染以及火山喷发污染排放遥感监测中具有非常明显的技术优势及巨大的应用前景.     

Electric Field Analysis of Space Charge Injection from a Conductive Nano-Filler Electrode

A simulation on the electric field distribution near the electrode is proposed to explain the reason for using nanosized carbon black mixed with ethylene vinyl acetate, as the electrode could lead to more charge injection into the polymer than using a deposited metal electrode. The electrode is simplified to a layer of conductive semi-spheres with fixed size and constant electric potential. By using the finite element method, it is found that both the size of the semi-spheres and the distance between adjacent semi-spheres could dramatically influence the electric field near the surface of the spheres; these are considered to be the two decisive factors for the charge injecting rate at electrodes of various materials.     

Electric Black Holes in a Model of Nonlinear Electrodynamics

The electric counterpart of the magnetic black hole solution found in nonlinear electrodynamics (NED) is presented. The electric field emerges regular and confined whereas the spacetime which satisfies all the energy conditions is singular. Our result is in conformation with a theorem proved before about the existence of regular electric black holes. The thermal properties of the black hole including the first law, Smarr's formula, and the thermal stability are investigated. This provides a chance to compare the electric and magnetic types of black holes in a particular model of NED.