Zn、Mn助剂对CuFe合成低碳醇催化剂的影响

研究了锌、锰助剂对CuFe合成低碳醇催化剂结构及性能的影响. 低温N2吸附、X射线衍射(XRD)和H2-程序升温还原(H2-TPR)结果表明, 锌的添加导致催化剂比表面下降, 不利于活性相的分散; 而锰则促进铜铁的分散, 增加了铜铁的接触面积, 有利于二者之间的相互作用. CO吸附的漫反射红外光谱(DRIFT)表明, 锌增强了铁对CO的吸附能力, 这种效应与ZnFe2O4的形成有直接关系; 而锰助剂由于稀释效应, 减弱了铁对CO吸附能力和链增长能力. 催化剂的反应性能测试表明, 与CuFe催化剂相比, CuZnFe催化剂的活性大幅度提高, 但C2+醇选择性下降; CuFeMn催化剂的活性却有所下降, C2+醇选择性也降低, 但总醇的选择性提高. 双助剂修饰的催化剂表现出明显的协同效应, 改变了催化剂的织构, 降低了Cu的还原温度, 修饰了Fe的还原性能. 更重要的是, Zn和Mn的添加显著增强了CO在催化剂表面的吸附量. 催化剂催化性能总体上优于CuZnFe和CuFeMn催化剂.     

锰助剂对F-T合成Co/Al2O3催化剂反应性能的影响

采用程序升温和原位红外技术对锰改性Co/Al2O3催化剂进行了表征，并与CO加氢反应活性和选择性进行关联.结果表明，添加适量锰能够增加反应活性，提高烃选择性，抑制甲烷及低碳烃的生成. XRD和FT IR结果表明锰助剂的添加能够促进活性相的分散，促进桥式CO吸附位数的增加. H2 TPD表明锰的加入可增加低温吸附氢量，但吸附氢量随锰含量的增加而减少.钴基催化剂的费托合成反应性能可以用锰添加导致的CO吸附态物种的变化来解释.     

过渡金属氧化物掺杂对铜锰氧化物催化CO氧化性能的影响

以乙酸铜和乙酸锰为铜锰前驱体,以NH4HCO3为沉淀剂,相应金属硝酸盐为掺杂剂,采用共沉淀法制备了不同过渡金属氧化物掺杂的铜锰氧化物催化剂.采用N2物理吸附、X射线衍射,氢气-程序升温还原和原位红外漫反射光谱等方法对催化剂进行了表征,考察了系列催化剂上CO反应性能.结果表明,掺杂过渡金属氧化物可以调变催化剂对CO的吸附能力,进而影响催化剂性能.     

FeMn、FeMnNa和FeMnK催化剂上合成气制低碳烯烃的比较(英文)

研究了钠、钾助剂对FeMn合成低碳烯烃催化剂结构及性能的影响.低温N2吸附、X射线光电子能谱(XPS)、X射线衍射(XRD)、H2程序升温还原(H2-TPR)、CO/CO2程序升温脱附(CO/CO2-TPD)、M?ssbauer谱和CO+H2反应的研究结果表明,增加Mn助剂含量促进了活性相的分散和低碳烯烃的生成,而过多锰助剂在催化剂表面的富集则降低了费托合成反应的CO转化率;钾助剂和钠助剂的加入均抑制了催化剂的还原并且促进了CO2和CO的吸附.比较还原后(H2/CO摩尔比为20)和反应后(H2/CO摩尔比为3.5)催化剂的体相结构可以发现,在FeMn、FeMnNa和FeMnK催化剂中,由于钾助剂的碱性和CO吸附能力较强,因此体相中FeCx的含量相对较高;而活性测试结果表明,FeMnNa催化剂拥有最好的CO转化率(96.2%)和低碳烯烃选择性(30.5%,摩尔分数).     

过渡金属氧化物掺杂对铜锰氧化物催化CO氧化性能的影响

以乙酸铜和乙酸锰为铜锰前驱体,以NH₄HCO₃为沉淀剂,相应金属硝酸盐为掺杂剂,采用共沉淀法制备了不同过渡金属氧化物掺杂的铜锰氧化物催化剂.?采用N₂物理吸附、X射线衍射,氢气-程序升温还原和原位红外漫反射光谱等方法对催化剂进行了表征,考察了系列催化剂上CO反应性能.?结果表明,掺杂过渡金属氧化物可以调变催化剂对CO的吸附能力,进而影响催化剂性能.     

Effects of Li Promoter on the Performance of Co/AC Catalysts for CO Hydrogenation to Mixed Linear a-Alcohols

采用CO加氢反应、X射线衍射、程序升温还原和CO程序升温脱附等技术研究了Li助剂对活性炭负载的Co催化剂(Co/AC)上CO加氢反应性能的影响.结果表明,Li的添加抑制了气态烃的生成,提高了C5+和直链混合伯醇的选择性,但催化剂活性下降.这可能源于Li的加入抑制了Co2+物种的还原,降低了反应速控步骤—强吸附CO的解离能力.另外,Li也促进了Co2C物种的生成,使得产物中混合醇的比例增加.     

FeMn、FeMnNa和FeMnK催化剂上合成气制低碳烯烃的比较

研究了钠、钾助剂对FeMn 合成低碳烯烃催化剂结构及性能的影响. 低温N₂吸附、X射线光电子能谱（XPS）、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、CO/CO₂程序升温脱附（CO/CO₂-TPD）、Mössbauer 谱和CO+H₂反应的研究结果表明,增加Mn助剂含量促进了活性相的分散和低碳烯烃的生成,而过多锰助剂在催化剂表面的富集则降低了费托合成反应的CO转化率;钾助剂和钠助剂的加入均抑制了催化剂的还原并且促进了CO₂和CO的吸附. 比较还原后（H₂/CO摩尔比为20）和反应后（H₂/CO摩尔比为3.5）催化剂的体相结构可以发现,在FeMn、FeMnNa和FeMnK催化剂中,由于钾助剂的碱性和CO吸附能力较强,因此体相中FeC_x的含量相对较高;而活性测试结果表明,FeMnNa催化剂拥有最好的CO转化率（96.2%）和低碳烯烃选择性（30.5%,摩尔分数）.     

钴基费-托合成催化剂上CO、H2的吸附行为

采用程序升温脱附及FT IR技术考察了CO、H2在钴基催化剂上的吸附行为.H2 TPD表明,Co/SiO2催化剂有两类脱附氢,引入锆助剂后,低温脱附氢量明显增加,高温吸附氢量下降.CO TPD及吸附态CO的红外光谱表明锆助剂使CO在钴催化剂上的吸附强度减弱,但其吸附量增大.钴基催化剂的费 托合成反应性能可以用吸附态物种的变化来解释.     

钴基费-托合成催化剂上CO、H_2的吸附行为

采用程序升温脱附及FT-IR技术考察了CO、H2在钴基催化剂上的吸附行为.H2-TPD表明,Co/SiO2催化剂有两类脱附氢,引入锆助剂后,低温脱附氢量明显增加,高温吸附氢量下降.CO-TPD及吸附态CO的红外光谱表明锆助剂使CO在钴催化剂上的吸附强度减弱,但其吸附量增大.钴基催化剂的费-托合成反应性能可以用吸附态物种的变化来解释.     

锰和镧改性Cu/ZrO2合成甲醇催化剂的结构及催化性能

 考察了锰和镧助剂对Cu/ZrO2催化剂上CO加氢合成甲醇反应性能的影响,并通过BET,XRD,TPR,H2-TPD和CO-TPD等手段对催化剂的结构及吸附-脱附性能进行了研究. 结果表明,锰和镧两种助剂均能有效地提高催化剂的活性,同时引入两种助剂时可使催化剂的活性进一步提高,表现出较强的协同效应. 一方面,锰的加入可使催化剂各组分的相互作用增强,特别是铜锰复合物的形成可有效地促进活性组分的分散,防止催化剂的烧结; 另一方面,镧助剂的引入进一步增强了铜锆在界面的相互作用,稳定了催化剂的活性中心,有利于吸附物种在两者之间发生溢流.     

Influence of promoter on catalytic properties of Cu-Mn-Fe/ZrO2 catalysts for alcohols synthesis

The addition of iron and manganese has a strong effect on the Cu/ZrO₂ catalyst performance for alcohols synthesis. The structures of catalysts have been investigated using X-ray adsorption spectroscopy and diffuse reflectance FTIR spectroscopy of absorbed CO. It is found that the Cu-Fe species and the interaction between them play an important role in converting the activity center for methanol synthesis to the center for higher alcohols synthesis.This revised version was published online in December 2005 with corrections to the Cover Date.     

改良铜钴催化剂体系上由合成气制混合醇的研究

在铜钴基催化剂体系上，由合成气制备混合醇的反应在６．０ＭＰａ的条件下进行．双活性组分体系中铜和钴是以强相互作用状态而共存的，分子探针实验表明，铜和钴的并存对于确保醇的碳链增长是重要的，助剂ＭｏＯ_ｘ的加入显著提高了Ｌａ_２Ｚｒ_２Ｏ_７担载的铜钴基催化剂Ｃｏ／ＣｕＬＺ的活性和选择性，其作用主要表现为通过氢的可逆溢流效应而改善了体系的氢化性能，和增大了ＣＯ的插入反应能力。在改良催化剂体系上，获得了５３％的醇选择性和１４７ｇ／Ｋｇｃａｔ／ｈ的混合醇产率，内含３３％的高级醇。     

Structure and Properties of Sol—Gel Derived CuNiMnZrO2 Catalysts for CO Hydrogenation

Two CuNiMnZrO2 catalysts (crystallized or non-crystallized) were prepared by co-hydrolyzing zirconium n-propoxide with Cu(NO3)2, Mn(NO3)2 and Ni(NO3)2 in an ethanol solution in the presence of diglycol. The physical and chemical properties of the catalysts were characterized using BET, XRD,TEM, XPS and CO-DRIFT techniques. It was found that the non-crystallizied CuNiMnZrO2 catalyst demonstrated highly dispersed active phases and high activity for CO adsorption, which resulted in good performance for synthesis of higher alcohols in CO hydrogenation compared to crystallized CuNiMnZrO2.     

含Y或La助剂的CuO／ZrO2合成甲醇催化剂的性能和结构研究

通过ＣｕＯ／ＺｒＯ２及含Ｙ或Ｌａ助剂的ＣｕＯ／ＺｒＯ２催化剂对ＯＣ／Ｈ２合成甲醇性能的研究，发现稀土助剂能有效地提高该催化剂的活性。ＸＲＤ结果说明，ＣｕＯ｜ＺｒＯ２中加入Ｙ或Ｌａ助剂可使氧化铜处于较高的分散状态。ＴＰＲ结果揭示ＣｕＯ／ＺｒＯ２催化剂中存在着在室温就很容易被氧人的铜，它在催化剂中含量的增加导致催化剂活性的提高，是关切的活性组份。助剂的加入使这种易被氧化的铜含量增加。ＸＰＳ表面分析结果     

催化剂中Cu含量对CVD法制备碳纳米管的影响

本文以溶胶-凝胶法制备了以铜为助剂的Ni/MgO催化剂，X-射线衍射(XRD)表明，经400 ℃氢气处理，催化剂中只有部分镍被还原，原因是NiO和MgO间存在强相互作用，形成固溶体。XRD和程序升温还原(TPR)表明，加入铜促进了镍的还原。CO化学吸附得出，随着催化剂中铜含量的增加，还原后催化剂表面镍原子数目增多，因此，催化剂的活性和反应寿命增加，C₂H₄裂解生成碳纳米管(CNT)的产率随之增加；但是，铜含量过高会引起催化剂表面镍颗粒增大，导致产物中纳米碳纤维（CNF）量增多，CNT量减少。对于约50% Ni/MgO催化剂，铜的最佳含量为4%～6%，此时得到的CNT产率最高，达36 g·g^-1，质量较好(纯度高、管径均匀、石墨化程度高)。     

层状复合氧化物La~4BaCu~5~-~xMn~xO~1~2的表征及在催化消除NO中活性的研究

采用柠檬酸配合法合成了结构呈层状ABO~3的La~4BaCu~5O~1~2复合氧化物, 并以它为基体合成了一系列Mn取代Cu的样品(La~4BaCu~5~-~xMn~xO~1~2, x=1-5)并利用XRD, IR进行了结构表征, 结果表明其均为5层的ABO~3结构。利用H~2-TPR考查了掺杂Mn以后样品的氧化还原性能的变化, 发现由于Mn的掺杂使Cu明显的容易还原。还考查了样品对NO+CO反应的催化活性, 结果表明反应的活性中心是Cu离子,但加入适量的Mn离子可以使活性提高。     

Effect of Cu promoter on Ni-based SBA-15 catalysts for partial oxidation of methane to syngas

A series of Ni/SBA-15 catalysts with 5wt% to 15wt% Ni content as well as a series of 12.5%Ni/Cu/SBA-15 catalysts with 1% to 10% copper content were prepared by the impregnation method. The catalytic performance for partial oxidation of methane was investigated in a continuous flow microreactor under atmospheric pressure. The textural and chemical properties of the catalysts were characterized by XRD, TEM, BET and H2-TPR techniques. The results indicated that the catalysts modified with Cu promoter showed better performance than those without modification. For the 12.5%Ni/2.5%/Cu/SBA-15 catalyst, at 850 ◦C the conversion of CH4 reached 97.9% and the selectivity of CO and H2 reached 98.0% and 96.0%, respectively. In XRD patterns of the Ni/Cu/SBA-15 catalyst with 7.5 to 10% Cu contents there were CuO characteristic peaks beside NiO characteristic peaks. The mesoporous structure of SBA-15 was retained in all of the catalysts. TPR analysis of the catalysts revealed that a strong interaction between Ni, Cu promoter and SBA-15 support may be existed. This interaction enhanced significantly the redox properties of the catalysts resulting in the higher catalytic activity.     

The remarkable enhancement of CO-pretreated CuO-Mn2O3/γ-Al2O3 supported catalyst for the reduction of NO with CO: the formation of surface synergetic oxygen vacancy

NO reduction by CO was investigated over CuO/γ-Al2O3, Mn2O3/γ-Al2O3, and CuOMn2O3/γ-Al2O3 model catalysts before and after CO pretreatment at 300 °C. The CO-pretreated CuO-Mn2O3/γ-Al2O3 catalyst exhibited higher catalytic activity than did the other catalysts. Based on X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV/Vis diffuse reflectance spectroscopy (DRS), Raman, and H2-temperature-programmed reduction (TPR) results, as well as our previous studies, the possible interaction model between dispersed copper and manganese oxide species as well as γ-Al2O3 surface has been proposed. In this model, Cu and Mn ions occupied the octahedral vacant sites of γ-Al2O3, with the capping oxygen on top of the metal ions to keep the charge conservation. For the fresh CuO/γ-Al2O3 and Mn2O3/γ-Al2O3 catalysts, the -Cu-O-Cu- and -Mn-O-Mn- species were formed on the surface of γ-Al2O3, respectively; but for the fresh CuO-Mn2O3/γ-Al2O3 catalyst, -Cu-O-Mn- species existed on the surface of -Al2O3. After CO pretreatment, -Cu-□-Cu- and -Mn-□-Mn- (□ represents surface oxygen vacancy (SOV)) species would be formed in CO-pretreated CuO/γ-Al2O3 and CO-pretreated Mn2O3/γ-Al2O3 catalysts, respectively; whereas -Cu-□-Mn- species existed in CO-pretreated CuO-Mn2O3/γ-Al2O3. Herein, a new concept, surface synergetic oxygen vacancy (SSOV), which describes the oxygen vacancy formed between the individual Mn and Cu ions, is proposed for CO-pretreated CuO-Mn2O3/γ-Al2O3 catalyst. In addition, the role of SSOV has also been approached by NO temperature-programmed desorption (TPD) and in situ FTIR experiments. The FTIR results of competitive adsorption between NO and CO on all the CO-pretreated CuO/γ-Al2O3, Mn2O3/γ-Al2O3, and CuO-Mn2O3/γ-Al2O3 samples demonstrated that NO molecules mainly were adsorbed on Mn2+ and CO mainly on Cu+ sites. The current study suggests that the properties of the SSOVs in CO-pretreated CuO-Mn2O3/γ-Al2O3 catalyst were significantly different to SOVs formed in CO-pretreated CuO/γ-Al2O3 and Mn2O3/γ-Al2O3 catalysts, and the SSOVs played an important role in NO reduction by CO.     

载体对浸渍型Cu/Mn/Mg/K甲醇裂解催化剂的影响

载体对浸渍型Cu/Mn/Mg/K甲醇裂解催化剂的影响;