ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

LB膜诱导Ba(NO3)2晶体取向生长

In this work, Ba(NO₃)₂ crystals with single crystal face were induced by using the the method of bio-mimetic mineralization and double LB films of behenic acid (BA) as the template. The crystals were characterized by Scanning Electron Microscope (SEM) and X-Ray Diffraction (XRD). The crystals were observed in regular square shape with uniform size about 5～8 μm by SEM, and they were found by XRD to grow along the (111) plane. From these experiments, we can conclude that the good selection of the (111) crystal face of Ba(NO₃)₂ is due to the electrostatic interactions , the match between this crystal face and the definite lattice structure of the LB films.     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

La2(CO3)3纳米线的微乳液法制备与表征

La₂(CO₃)₃ nanowires were prepared in the nonionic surfactant microemulsion(Triton X-100/cyclohexane/water)system. Transmission electron microscopy (TEM) and selected area electronic diffraction (SAED) were used to characterize the shape and size of the products. The results showed that the pH value and concentration of mother solution, temperature and aging time all could affect the morphology and size of the La₂(CO₃)₃ nanowires. The lengths of the nanowires were more than 10 μm and the diameters were in the range of 30～200 nm.     

Eu0.5RE0.5Fe0.5Mn0.5O3的57Fe Msosbauer谱研究

利用固相反应合成了Eu0.5RE0.5Fe0.5Mn0.5O3(RE=La,Pr,Nd,Sm,Eu,Gd,Tb,Dy,Ho,Er,Tm,Yb,Y)等化合物。测量了其XRD谱及57FeMssbauer谱。实验发现,随着RE原子序数的增加,样品的晶胞体积减小,Fe在化合物中处于Fe3+的高自旋状态,57Fe的四极裂矩与样品的畸变参数D成线性关系。     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

Li2CO3、NiO和电解MnO2合成高容量LiNi0.5Mn1.5O4及其表征

Well-developed crystalline LiNi_0.5Mn_1.5O₄ was prepared by solid-state reaction using Li₂CO₃, NiO and electrolytic MnO₂ at high heating and cooling rate. X-ray diffraction (XRD) patterns and scanning electron microscopic (SEM) images showed that LiNi_0.5Mn_1.5O₄ synthesized at 900 ℃ and 950 ℃ had cubic spinel structure with clearly defined shape. LiNi_0.5Mn_1.5O₄ spinel phase decomposed at 1 000 ℃ accompanying with structural and morphological degradation. TG measurement revealed that the weight loss during heating process could be mostly gained in cooling process, and the upward tendency of weight loss during heating process decreased, while that of irreversible weight loss rapidly increased with the increase of temperature. LiNi_0.5Mn_1.5O₄ powders prepared at 900 ℃ for 12 h delivered the maximum discharge capacity of 134 mAh·g^-1 with good cyclic performance at 2/7 C. In addition, by adjusting the calcination time at 900 ℃, the capacity and cycling performance of LiNi_0.5Mn_1.5O₄ were further enhanced.     

(ZrO2)1-x(Yb2O3)x纳米晶的水热法合成及其烧结体的电性能

(ZrO₂)_1-x(Yb₂O₃)_x (x=0.07, 0.09, 0.11) nanocrystallites were hydrothermally prepared in basic media by using co-precipitated Zr(OH)₄ and Yb(OH)₃ as precursor. The nanocrystallites have small particle sizes of 5.8~7.5 nm, narrow size distribution, less agglomeration and high sinterability. The oxide-ionic conduction properties of the prepared ceramics were investigated by means of AC impedance spectroscope, oxygen concentration cell at 600~1 000 ℃. The results show that the ceramic with x=0.09 is superior to the ceramics with x=0.07 and 0.11 in oxide-ionic conduction.     

球形Gd2O3∶Eu纳米发光材料的制备

Spherical nanometer Gd₂O₃∶Eu luminescent materials were prepared by homogeneous precipitation method, and the properties were studied also. TG, FTIR and XRD analysis showed that the precursor was carbonate, the cubic Gd₂O₃was obtained after calcination. TEM photographs indicated that the samples were spherical and well dispersed with nanometer and submicrometer size of 200～300 nm which is the nanoparticles’ aggregate. The mechanics of agglomerating growth is also discussed. ED photograph showed that the particle was crystalline. The PL analysis exhibited that CTB band of nanometer Gd₂O₃∶Eu was of 17 nm red shift to bulk materials, and the emission peak was broadened due to the surface and interface effect of nanocrystals.     

纳米钙钛矿型LaFe1-xNixO3(x=0~1.0)的制备及其在紫外光激发下的电化学性能

本文采用溶胶-凝胶法制备了LaFe1-xNixO3(x=0,0.2,0.4,0.6,0.8,1.0)纳米晶粉末,利用XRD、TEM和电化学测试方法对LaFe1-xNixO3材料的相结构、形貌、成分组成和其在碱液中的充放电性能以及电化学动力学性能等方面进行了表征和分析,同时对电极受紫外光激发前后的电化学行为进行了对比研究。XRD和TEM分析表明,用硝酸盐作为原材料和溶胶-凝胶方法可制备出单一相结构的纳米晶钙钛矿型LaFe1-xNixO3复合氧化物,随Ni替代量x的增大,LaFe1-xNixO3的相结构由正交结构向菱面体结构转变,其分子体积和晶粒尺寸呈现减小的趋势。电化学研究结果表明,紫外光激发前,LaFe1-xNixO3电极的放电容量随x的增加而逐渐增大;光激发后,电极的放电容量和交换电流Io与未激发前相比显著提高,当x=0.4时其放电容量具有最大值483.1mAh·g-1,Io值由光激发前的3.54～11.58 mA·g-1大幅增加至激发后的8.37～40.11 mA·g-1。     

锰源对燃烧法制备5V级正极材料LiNi0.5Mn1.5O4的影响

以硝酸锰和醋酸锰,采用蔗糖燃烧法制备锂离子电池正极材料LiNi0.5Mn1.5O4通过XRD、SEM、粒径分布测试、循环伏安、恒流充放电测试以及交流阻抗等方法,研究了醋酸锰和硝酸锰对产物的结构、形貌、粒径及电化学性能的影响。XRD测试结果表明样品的结构都为立方尖晶石型,属于Fd3m空间群。不同的锰源对材料的粒径及粒径分布有很大的影响。以醋酸锰为原料制得的材料的粒径较小并且分布更均匀,有利于锂离子的脱出和嵌入从而提高电化学性能。以醋酸锰为锰源制得的LiNi0.5Mn1.5O4在3.6~5.2 V的充放电电压范围内的电化学性能更好,1C(1C=140.0 mA.g-1)倍率的首次放电容量为144.5 mAh.g-1,循环100周后容量保持率为96%,在3C,5C,10C以及20C的放电容量分别为136.3,132.0,124.7以及96.6 mAh.g-1。     

Mn1-x(Li,Ti)xCo2O4尖晶石型复合氧化物的制备、表征与催化性能

用柠檬酸配位燃烧法合成了Mn_1-x(Li,Ti)_xCo₂O₄系列尖晶石型复合氧化物催化剂，使用FTIR和XRD方法对催化剂结构进行表征，通过程序升温氧化反应(TPO)技术对这些催化剂在模拟柴油机尾气条件下进行同时消除NO_x和柴油碳黑反应的活性评价。结果表明，掺杂Li或Ti后的Mn_1-x(Li,Ti)_xCo₂O₄系列催化剂仍然保持了完整的尖晶石型复合氧化物结构，这些催化剂对同时消除柴油机尾气中的碳黑颗粒和NO_x具有良好的催化性能，其中Li或Ti的掺杂量为x=0.05较佳，结合碳黑燃烧与NO_x还原总的催化效果，Mn_0.95Li_0.05Co₂O₄具有最好的催化活性。     

尖晶石型LiMn2-xInxO4(x=0，0.01，0.02，0.05)的合成及电化学性能研究

以醋酸锰、氢氧化锂和三氧化二铟为原料,以柠檬酸为配位剂,采用溶胶-凝胶法制备了掺杂In的尖晶石LiMn2-xInxO4(x=0,0.01,0.02,0.05),采用XRD、SEM对目标材料进行了结构和形貌表征,采用恒流充放电、循环伏安(CV)以及交流阻抗(EIS)谱测试对材料进行了电化学性能表征,考察了不同In掺杂量对材料性能的影响。结果表明,当In掺杂量为1%时,LiMn1.99In0.01O4样品具有纯的尖晶石锰酸锂结构,在0.5C和3.4～4.35 V电压范围条件下,LiMn1.99In0.01O4的初始放电容量为119.9 mAh.g-1,经过1C 30次,2C 30次,再0.5C 5次循环后,其放电容量保持率为84.9%,显示了良好的电化学性能。掺杂1%的In的样品比未掺杂的样品具有更优的高温循环稳定性能。     

正极材料Li_(0.99)Nb_(0.01)Fe_(1-x)Mg_xPO_4/C的制备及电化学性能的研究

采用两步固相反应合成了锂、铁双位掺杂的锂离子电池正极材料Li0.99Nb0.01Fe1-xMgxPO4/C(x=0,0.01,0.02,0.03,0.04)。通过X射线衍射(XRD)、扫描电镜(SEM)以及恒电流充放电测试,研究了复合材料的晶体结构、形貌以及电化学性能。实验结果表明,制备的Li0.99Nb0.01Fe1-xMgxPO4/C(x=0,0.01,0.02,0.03,0.04)为纯相,掺杂适量的Nb5+、Mg2+离子可减小材料的晶粒尺寸,当Nb离子掺杂量为1mol%、Mg离子掺杂量为3mol%时,Li0.99Nb0.01Fe0.97Mg0.03PO4/C的电化学性能最佳。室温下,0.2C、1C、2C、4C(1C=170mA·g-1)倍率充放电其首次放电比容量分别为153.7、149.7、144.6、126.4mAh·g-1,即使在8C倍率下放电其放电比容量也有92.2mAh·g-1,并表现出良好的循环性能。     

溶胶-凝胶法合成Li1-xNaxMn2O4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na⁺离子掺杂的Li_1-xNa_xMn₂O₄(x=0,0.01,0.03,0.05)。X射线衍射图表明Na⁺取代Li⁺进入Li_1-xNa_x Mn₂O₄晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_0.97Na_0.03Mn₂O₄在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn₂O₄从51.2%提升到84.1%。循环伏安测试表明Na⁺离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li_0.97Na_0.03Mn₂O₄仍有79.0 mAh·g^-1的放电容量,高于未掺杂样品的52.1 mAh·g^-1。Na⁺离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn₂O₄的电化学性能,是一种可行的改性方法。     

La、Ce、Yb掺杂对LiNi0.5Mn1.5O4高电压正极材料性能的影响

采用低温燃烧法制备出不同稀土元素掺杂的高电压镍锰酸锂(LiNi_(0.5)Mn_(1.5)O_4)正极材料,探究了不同掺杂比例(物质的量分数0.5%、1%、2%)和不同掺杂稀土元素(La、Ce、Yb)对样品性能的影响,并通过X射线衍射、拉曼光谱、电子顺磁共振和恒电流间歇滴定等技术探究了其影响机理。从X射线衍射图可以看出,稀土掺杂可以抑制Li_xNi_(1-x)O杂质相的产生;电感耦合等离子谱结果表明,掺杂进入的稀土元素与设计比例基本相符;从拉曼光谱图可以看出,稀土元素可以使样品的有序相增多,其中Ce掺杂样品的有序相最多;结合电子顺磁共振波谱氧空位测试,发现Ce掺杂诱导了样品中有序相比例增加,从而使样品的稳定性提高;经恒电流间歇滴定技术测试发现,Ce掺杂镍锰酸锂样品的扩散系数比未掺杂样品高了约15倍;在不同掺杂比例上,1%掺杂量时样品性能最佳。在3种最佳掺杂量的稀土元素样品中,Ce掺杂的样品性能最优,首次放电比容量可以达到133.3mAh·g~(-1),比未掺杂样品放电比容量高且首次效率提高了 18%,在1C下循环200次后,容量保持率为102%,比未掺杂样品提高了 8%。     

溶胶-凝胶法合成Li_(1-x)Na_xMn_2O_4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na+离子掺杂的Li_(1-x)Na_xMn_2O_4(x=0,0.01,0.03,0.05)。X射线衍射图表明Na+取代Li+进入Li_(1-x)Na_xMn_2O_4晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_(0.97)Na_(0.03)Mn_2O_4在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn_2O_4从51.2%提升到84.1%。循环伏安测试表明Na+离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li0.97Na0.03Mn2O4仍有79.0 m Ah·g-1的放电容量,高于未掺杂样品的52.1 m Ah·g~(-1)。Na+离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn_2O_4的电化学性能,是一种可行的改性方法。     

锂离子电池正极材料LiV3-xAlxO8的水热合成与性能

采用水热法制备了Al掺杂的锂二次电池正极材料LiV3-xAlxO8,并用X射线衍射和扫描电镜对材料的晶体结构和形貌进行了表征.以50 mA·g-1进行恒流充放电测试,结果表明Al掺杂能够明显改善材料的电化学性能.在掺杂改性的LiV3-xAlxO8材料中,LiV2.93Al0.07O8的初始容量最高,达到325 mAh·g-1.当掺杂量为x=0.04时,材料的循环性能最佳.LiV2.96Al0.04O8经20次循环后仍保持179 mAh·g-1的比容量,且充放电效率始终维持在98%左右.     

Ni-Mn共掺杂高电压钴酸锂锂离子电池正极材料

以金属硫酸盐为原料,NaOH和NH₃·H₂O为沉淀剂,用共沉淀法合成了Co_0.9Ni_0.05Mn_0.05(OH)前驱体,再进行配锂并通过高温固相法合成了Ni-Mn共掺杂高电压钴酸锂锂离子电池正极材料Li(Co_0.9Ni_0.05Mn_0.05)O₂。用X射线衍射(XRD)、扫描电镜(SEM)、 循环伏安(C-V)、交流阻抗(EIS)和充放电测试研究样品的晶体结构、形貌和电化学性能。结果表明Ni-Mn共掺杂正极材料Li(Co_0.9Ni_0.05Mn_0.05)O₂有优秀的电化学性能:在3.0~4.4 V和3.0~4.5 V区间,0.5C倍率下首次放电比容量分别为162 mAh·g^-1和187 mAh·g^-1,循环100次后容量保持率分别为94%和94%。