Sonochemical conversion of CO2 into hydrocarbons: The Sabatier reaction at ambient conditions

In this study, we investigated an alternative method for the chemical CO₂ reduction reaction in which power ultrasound (488 kHz ultrasonic plate transducer) was applied to CO₂-saturated (up to 3%) pure water, NaCl and synthetic seawater solutions. Under ultrasonic conditions, the converted CO₂ products were found to be mainly CH₄, C₂H₄ and C₂H₆ including large amount of CO which was subsequently converted into CH₄. We have found that introducing molecular H₂ plays a crucial role in the CO₂ conversion process and that increasing hydrogen concentration increased the yields of hydrocarbons. However, it was observed that at higher hydrogen concentrations, the overall conversion decreased since hydrogen, a diatomic gas, is known to decrease cavitational activity in liquids. It was also found that 1.0 M NaCl solutions saturated with 2% CO₂ + 98% H₂ led to maximum hydrocarbon yields (close to 5%) and increasing the salt concentrations further decreased the yield of hydrocarbons due to the combined physical and chemical effects of ultrasound. It was shown that CO₂ present in a synthetic industrial flue gas (86.74% N₂, 13% CO₂, 0.2% O₂ and 600 ppm of CO) could be converted into hydrocarbons through this method by diluting the flue gas with hydrogen. Moreover, it was observed that in addition to pure water, synthetic seawater can also be used as an ultrasonicating media for the sonochemical process where the presence of NaCl improves the yields of hydrocarbons by ca. 40%. We have also shown that by using low frequency high-power ultrasound in the absence of catalysts, it is possible to carry out the conversion process at ambient conditions i.e., at room temperature and pressure. We are postulating that each cavitation bubble formed during ultrasonication act as a “micro-reactor” where the so-called Sabatier reaction -$C{O}_2+4H_2\stackrel{\mathit{Ultrasonication}}{\to }C{H}_4+2H_{2}O$ - takes place upon collapse of the bubble. We are naming this novel approach as the “Islam-Pollet-Hihn process”.     

Preparation of modified MFI (ZSM-5 and silicalite-1) zeolites for potassium extraction from seawater

Modified nanosized MFI (ZSM-5 and silicalite-1) zeolites were successfully synthesized by a hydrothermal method using aluminum isopropoxide and tetraethylorthosilicate as the raw materials. The synthetic zeolites were characterized by X-ray diffraction, energy dispersion spectroscopy, and scanning electron microscopy. The ZSM-5 and silicalite-1 zeolites exhibited ellipse-like and cubic columns, respectively. The K⁺ ion-exchange equilibrium and ion-exchange capacity of the synthetic zeolites in seawater were investigated. The K⁺ ion-exchange of synthetic zeolites was rapid and reached an ion-exchange balance in approximately 20 min. The K⁺ ion-exchange capacity of ZSM-5 and silicalite-1 in seawater was 56.7 and 48.7 mg/g, respectively. The synthetic zeolites have high selectivity toward K⁺, and therefore, they can be used to selectively extract potassium from seawater.     

Dynamically Restructuring NixCryO Electrocatalyst for Stable Oxygen Evolution Reaction in Real Seawater

In the pursuit of long-term stability for oxygen evolution reaction (OER) in seawater, retaining the intrinsic catalytic activity is essential but has remained challenging. Herein, we developed a Ni_xCr_yO electrocatalyst that manifested exceptional OER stability in alkaline condition while improving the activity over time by dynamic self-restructuring. In 1 M KOH, Ni_xCr_yO required overpotentials of only 270 and 320 mV to achieve current densities of 100 and 500 mA cm⁻², respectively, with excellent long-term stability exceeding 475 h at 100 mA cm⁻² and 280 h at 500 mA cm⁻². The combination of electrochemical measurements and in situ studies revealed that leaching and redistribution of Cr during the prolonged electrolysis resulted in increased electrochemically active surface area. This eventually enhanced the catalyst porosity and improved OER activity. Ni_xCr_yO was further applied in real seawater from the Red Sea (without purification, 1 M KOH added), envisaging that the dynamically evolving porosity can offset the adverse active site-blocking effect posed by the seawater impurities. Remarkably, Ni_xCr_yO exhibited stable operation for 2000, 275 and 100 h in seawater at 10, 100 and 500 mA cm⁻², respectively. The proposed catalyst and the mechanistic insights represented a step towards realization of non-noble metal-based direct seawater splitting.     

流动注射法同时测定海水中氨氮和磷酸盐

采用流动注射法同时测定海水中氨氮和磷酸盐的含量。在优化的试验条件下,氨氮和磷酸盐的线性范围分别为0.25 mg·L-1和0.30 mg·L-1以内,检出限(3S/N)分别为0.42μg·L-1和0.56μg·L-1。氨氮和磷酸盐加标回收率分别在85.0%~103%和86.7%~103%之间,测定值的相对标准偏差(n=6)分别在0.43%~5.3%和0~4.1%之间。方法用于分析标准物质,测定结果与分光光度法的结果一致。     

High-precision measurements of seawater Pb isotope compositions by double spike thermal ionization mass spectrometry

A new method for the determination of seawater Pb isotope compositions and concentrations was developed, which combines and optimizes previously published protocols for the separation and isotopic analysis of this element. For isotopic analysis, the procedure involves initial separation of Pb from 1 to 2 L of seawater by co-precipitation with Mg hydroxide and further purification by a two stage anion exchange procedure. The Pb isotope measurements are subsequently carried out by thermal ionization mass spectrometry using a ²⁰⁷Pb–²⁰⁴Pb double spike for correction of instrumental mass fractionation. These methods are associated with a total procedural Pb blank of 28 ± 21 pg (1sd) and typical Pb recoveries of 40–60%. The Pb concentrations are determined by isotope dilution (ID) on 50 mL of seawater, using a simplified version of above methods. Analyses of multiple aliquots of six seawater samples yield a reproducibility of about ±1 to ±10% (1sd) for Pb concentrations of between 7 and 50 pmol/kg, where precision was primarily limited by the uncertainty of the blank correction (12 ± 4 pg; 1sd). For the Pb isotope analyses, typical reproducibilities (±2sd) of 700–1500 ppm and 1000–2000 ppm were achieved for ²⁰⁷Pb/²⁰⁶Pb, ²⁰⁸Pb/²⁰⁶Pb and ²⁰⁶Pb/²⁰⁴Pb, ²⁰⁷Pb/²⁰⁴Pb, ²⁰⁸Pb/²⁰⁴Pb, respectively. These results are superior to literature data that were obtained using plasma source mass spectrometry and they are at least a factor of five more precise for ratios involving the minor ²⁰⁴Pb isotope. Both Pb concentration and isotope data, furthermore, show good agreement with published results for two seawater intercomparison samples of the GEOTRACES program. Finally, the new methods were applied to a seawater depth profile from the eastern South Atlantic. Both Pb contents and isotope compositions display a smooth evolution with depth, and no obvious outliers. Compared to previous Pb isotope data for seawater, the ²⁰⁶Pb/²⁰⁴Pb ratios are well correlated with ²⁰⁷Pb/²⁰⁶Pb, underlining the significant improvement achieved in the measurement of the minor ²⁰⁴Pb isotope.     

微生物发酵诱导多孔材料: 制备方法和应用

微生物发酵作为一种新的制备多孔材料的方式, 将微生物发酵工程与发泡工程有机结合起来, 克服了传统制备方法需要特殊设备、 操作复杂、 后处理繁琐、 化学药品污染和成本昂贵等缺点, 受到了广泛关注.本文基于微生物发酵多孔材料的研究, 围绕多孔材料的定义和多孔水凝胶的分类及制备方式进行总结.针对微生物发酵诱导制备多孔材料的制备方法, 综合评述了该方法在染料吸附、 海水蒸发脱盐、 电磁屏蔽以及制备新型功能性生物材料等方面的应用.最后, 对微生物诱导制备多孔材料的未来发展进行了展望.     

海水电解面临的挑战与机遇：含氯电化学中先进材料研究进展

氢气是一种清洁高效的能源载体,通过海水电解规模化制备氢气能够为应对全球能源挑战提供新的机遇。然而,缺乏高活性、高选择性和高稳定性的理想电极材料是在腐蚀性海水中连续电解过程的一个巨大挑战。为了缓解这一困境,需要从基础理论和实际应用两方面对材料进行深入研究。近年来,人们围绕电极材料的催化活性、选择性和耐腐蚀性进行了大量的探索。本文重点总结了高选择性和强耐腐蚀性材料的设计合成与作用机制。其中详细介绍了多种电极材料(如多金属氧化物、Ni/Fe/Co基复合材料、氧化锰包覆异质结构等)对氧气生成选择性的研究进展;系统论述了各种材料的抗腐蚀工程研究成果,主要讨论了本征抗腐蚀材料、外防护涂层和原位产生抗腐蚀物种三种情况。此外,提出了海水电解过程中存在的挑战和潜在的机遇。先进纳米材料的设计有望为解决海水电解中的氯化学问题提供新思路。     

复合光催化剂CdS-Pt/TiO2制备及可见光光解海水制氢性能

水热法制备了单斜CdS与Pt/TiO2复合的光催化剂.通过X射线衍射、紫外-可见漫反射光谱、荧光光谱、扫描电子显微镜和BET方法对催化剂进行了表征.以可见光光解纯水和海水制氢为探针反应,考察了CdS-Pt/TiO2光催化剂的活性.结果表明:海水中无机盐的存在有利于电子给体捕获光生空穴,提高了电子和空穴的分离效果;海水中单斜CdS可转化为立方和六方混合晶相.最佳条件下,催化剂光解海水制氢活性比纯水提高了33%,而且有较高的稳定性.     

Determination of five booster biocides in seawater by stir bar sorptive extraction–thermal desorption–gas chromatography–mass spectrometry

Stir bar sorptive extraction (SBSE) and thermal desorption (TD)–gas chromatography–mass spectrometry (GC–MS) have been optimized for the determination of five organic booster biocides (Chlorothalonil, Dichlofluanid, Sea-Nine 211, Irgarol 1051 and TCMTB) in seawater samples. The parameters affecting the desorption and absorption steps were investigated using 10 mL seawater samples. The optimised conditions consisted of an addition of 0.2 g mL⁻¹ KCl to the sample, which was extracted with 10 mm length, 0.5 mm film thickness stir bars coated with polydimethylsiloxane (PDMS), and stirred at 900 rpm for 90 min at room temperature (25 °C) in a vial. Desorption was carried out at 280 °C for 5 min under 50 mL min⁻¹ of helium flow in the splitless mode while maintaining a cryotrapping temperature of 20 °C in the programmed-temperature vaporization (PTV) injector of the GC–MS system. Finally, the PTV injector was ramped to a temperature of 280 °C and the analytes were separated in the GC and detected by MS using the selected-ion monitoring (SIM) mode. The detection limits of booster biocides were found to be in the range of 0.005–0.9 μg L⁻¹. The regression coefficients were higher than 0.999 for all analytes. The average recovery was higher than 72% (R.S.D.: 7–15%). All these figures of merit were established running samples in triplicate. This simple, accurate, sensitive and selective analytical method may be used for the determination of trace amounts of booster biocides in water samples from marinas.     

Sulfide determination in hydrothermal seawater samples using a vibrating gold micro-wire electrode in conjunction with stripping chronopotentiometry

A rapid electrochemical stripping chronopotentiometric procedure to determined sulfide in unaltered hydrothermal seawater samples is presented. Sulfide is deposited at −0.25 V (vs Ag/AgCl, KCl 3 M) at a vibrating gold microwire and then stripped through the application of a reductive constant current (typically −2 μA). The hydrodynamic conditions are modulated by vibration allowing a short deposition step, which is shown here to be necessary to minimize H₂S volatilization. The limit of detection (LOD) is 30 nM after a deposition step of 7 s. This LOD is in the same range as the most sensitive cathodic voltammetric technique using a mercury drop electrode and is well below those reported previously for other electrodes capable of being implemented in situ.