触媒组分对高温高压金刚石大单晶生长及裂纹缺陷的影响

本文利用六面顶压机,在5.6 GPa, 1250—1450℃的高压高温条件下,分别选用FeNiCo和NiMnCo触媒合金开展了金刚石大单晶的生长实验,系统地考察了触媒组分对金刚石单晶裂纹缺陷的影响.首先,通过对两种组分触媒晶体生长实验对比发现,金刚石大单晶裂纹缺陷出现的概率与触媒组分相关联.同NiMnCo触媒相比, FeNiCo触媒生长的金刚石单晶更容易出现生长裂纹.我们认为,这与FeNiCo触媒黏度高、流动性差、碳素输运能力差、生长中晶体比表面积大,进而导致其对生长条件稳定性的要求较高有关.其次,两种触媒极限增重速度和生长时间的关系曲线表明,相同生长时间条件下, NiMnCo触媒生长金刚石单晶的极限增重速度相对较大.再次,扫描电子显微镜测试结果表明,裂纹缺陷的出现与否同晶体表面平整度的高低无必然联系,表面平整度高的金刚石单晶内部也可能存在裂纹缺陷.最后,经对金刚石单晶傅里叶微区红外测试结果进行分析,得出了氮杂质含量的高低与金刚石单晶裂纹缺陷的出现与否无内在关联性的研究结论.     

CrN镀层的微粒磨损性能及其切削行为研究

在Teer UDP 550型闭合场非平衡磁控溅射离子镀设备上制备CrN镀层,以球-盘方法测定的比磨损率和微粒磨损法测定的微粒磨损率评价CrN镀层的耐磨性能,采用高速钢镀层钻头的钻孔数评价镀层的切削性能.结果表明,CrN镀层的微粒磨损率对氮流量(用光谱发射因子OEM值控制)的变化很敏感,而比磨损率却不能反映这种由于氮流量变化带来的镀层结构和性能的变化.在不同偏压条件下所制备的镀层微粒磨损率变化不明显.当微粒磨损率低于某一值时,CrN镀层的钻孔寿命明显提高,而比磨损率则无此规律.     

LYVE-1 在甲状腺乳头状癌的表达和意义

目的 观察淋巴管透明质酸受体1（LYVE-1）的表达和癌周组织中淋巴管的生成情况在甲状腺恶性肿瘤的变化及转 移中的作用。方法 应用免疫组织化学和real-time PCR方法检测45 例甲状腺乳头状癌中央区、癌周边区和正常甲状腺组织中的LYVE-1及其mRNA 表达情况,并计算淋巴管密度（LVD）。结果 甲状腺乳头状癌周边区LVD 高于甲状腺乳头状癌中央区,而正常组织中很少见LYVE-1 阳性的微淋巴管;甲状腺乳头状癌周边区LVD 与淋巴结转移有密切关系（P＜0.05）。结论 LYVE-1是一种特异性较高的淋巴管内皮特异性标志物,对淋巴管生成促进甲状腺乳头状癌的淋巴结转移。     

Syntheses and Crystal Structures of Two Tin(Ⅳ) Complexes with Aminosilane Bearing Ligand

Aminosilane bearing bulky substituents on nitrogen: LH2(L=Me2Si(NDipp-)2 , Dipp=2,6-diisopropylphenyl) was reacted with BuLi in toluene. The resulting bulky chelating dianion Me2Si(NDipp-)2 was used to synthesize the unusual spirocyclic heterotriatomic complex [Me2Si(NDipp)2]2Sn (1) by its reaction with SnCl4 and the bulky heterotriatomic complex Me2Si(NDipp)2SnPh2 (2) with Ph2SnCl2.1 belongs to the monoclinic system, space group P21/n with a=13.193(2), b=20.663(3), c=20.403(3), β=99.954(2)o, V=5478.3(15)3 , C55H85.5N4Si2Sn, Mr=977.64, Z=4, Dc=1.185Mg/m3 , μ(MoKα)=0.547mm-1 , F(000)=2086, S=1.000, the final R=0.0614 and wR=0.1322 for 14446 observed reflections (I2σ(I)) and R=0.0797 and wR=0.1456 for all data. 2 belongs to the triclinic system, space group Pī with a=10.36(15), b=13.204(7), c=14.363(7), α=90.214(10), β=106.182(7), γ=109.854(8)o, V=1764.4(15)3 , C38H50N2SiSn, Mr=681.58, Z=2, Dc=1.283 Mg/m3 , μ(MoKα)=0.785 mm-1 , F(000)=712, S=1.002, the final R=0.0498 and wR=0.0955 for 7533 observed reflections (I2σ(I)) and R=0.0676 and wR=0.1018 for all data. In the structure of 1, the tin atom is located in the spirocyclic center of the two fused four-membered SnN 2 Si rings. The two complexes were characterized by 1H NMR, elemental analysis, and single-crystal X-ray structural analysis.     

Theoretical Study on the Structural and Optoelectronic Properties of the Linear Perfluorooctane Sulfonate （PFOS）

The perfluoroalkyl substances(PFS) have attracted considerable attention in recent years as a persistent global pollutant to be able to bioaccumulate in higher organisms.In this paper,theoretical analysis on electronic structures,optoelectronic properties and absorption spectra properties of the perflurooctane sulfonate(PFOS) in gas phase have been investigated by using the DFT/TD-DFT method.The geometric structures,electrostatic potentials,energy gaps,ionization potentials,electron affinities,frontier molecular orbital,excitation energies and absorption spectra for the ground state of PFOS were calculated.The result indicates that the ability of accepting electron of neutral PFOS is larger than that of anionic PFOS,while the electron excited by UV irradiation from HOMO to LUMO in the anionic PFOS is easier than that in the neutral PFOS.     

Fabrication of an Integrated Pixel with an Organic Light-Emitting Diode Driven by Copper Phthalocyanine Organic Thin Film Transistors

An organic integrated pixel with organic light-emitting diodes （OLEDs） driven by organic thin film transistors （OTFTs） is fabricated by a greatly simplified processing. The OTFTs are based on copper phthalocyanine as the active medium and fabricated on indium-tin-oxide （ITO） glass with top-gate structure, thus an organic integrated pixel is easily made by integrating OLED with OTFT. The OTFTs show field-effect mobility of 0.4cm^2/Vs and on/off ratio of 10^3 order. The OLED is driven well and emits the brightness as large as 2100cd/m^2 at a current density of 14.6 μA /cm^2 at -19.7 V gate voltage. This simple device structure is promising in the future large-area flexible OLED displays.     

我国高等学校分析化学教材建设研究

从教材出版工作者的角度,对我国高等学校分析化学课程改革,特别是分析化学教材建设的发展进行了初步研究。从时间上看,分析化学教材的发展经历了雏形期、发展期和成熟期3个时期。文中重点阐述了不同时期典型分析化学教材的外在表现形式和具体教学内容的特点和变化,并对分析化学教材的建设趋势进行了初步探讨。     

添加纳米固体润滑剂的自润滑陶瓷材料高温摩擦磨损性能研究

采用真空热压烧结工艺制备了一种添加纳米固体润滑剂CaF2的自润滑陶瓷材料,研究其在室温25℃到600℃环境下与40Cr钢销干摩擦时的摩擦磨损性能.结果表明:自润滑陶瓷材料的摩擦系数与磨损率随环境温度的升高而逐渐降低,600℃时摩擦系数降低到0.21,磨损率降低到2.4×10-6 mm3/N·m.常温下自润滑陶瓷材料的磨损机理是磨粒磨损,高温环境同时存在磨粒磨损和粘着磨损.高温环境下摩擦表面纳米CaF2含量的增加和固体润滑膜的形成是摩擦磨损性能改善的主要原因.     

气相色谱-微池电子捕获检测器分析茶叶中杀螟丹的残留

介绍了一种快速、灵敏、可靠的适用于茶叶样品中杀螟丹残留量的气相色谱分析方法。茶叶样品经过0.05 mol/L盐酸溶液提取,液-液分配净化,在碱性条件下用正己烷萃取提取液中的杀螟丹,用毛细管气相色谱法-微池电子捕获检测器（μ-ECD）测定杀螟丹的残留量。结果表明：样品的添加回收率为70.2%~92.0%,相对标准偏差小于10%,方法的检测低限为0.01 mg/kg,符合农药残留分析的要求。     

用重离子实验数据推算质子翻转截面和轨道翻转率

空间单粒子辐射环境主要由重离子和高能质子构成,但在地面利用两种离子评估器件单粒子效应敏感度成本太高,因此利用重离子实验数据推算质子敏感参数成为一个非常活跃的研究课题.利用Barak经验公式,在重离子实验获得器件的σ LET值曲线的基础上,计算了几种典型器件在不同能量下的质子翻转截面以及典型轨道上质子引起的翻转率,并同FOM方法预示的质子翻转率进行了比较,其结果将对卫星电子系统抗辐射加固设计具有重要参考价值. The radiation environments concerned with single event upset mainly consist of heavy ions from cosmic ray and large flux proton from solar events and planetary radiation belts. The most reliable calculation for SEE rate induced by proton and henvy ions are the way to use the experimentally measured data rospectively. But it is too expensive to test devices with both heavy ions and protons. So it is necessary to derive models for predicting proton cross sections and rates from heavy ion test data....