Formation of Supramolecular Nanostructures through in Situ Self-Assembly and Post-Assembly Modification of a Biocatalytically Constructed Dipeptide Hydrazide**

Aqueous self-assembly of short peptides has attracted growing attention for the construction of supramolecular materials for various bioapplications. Herein, we describe how the thermolysin-assisted biocatalytic construction of a dipeptide hydrazide from an N-protected amino acid and an amino acid hydrazide leads to the formation of thermally stable supramolecular hydrogels. In addition, we demonstrate the post-assembly modification of the supramolecular architectures constructed in situ tethering hydrazide groups as a chemical handle by means of fluorescence imaging.     

Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

Crosslinking network of bio‐based bis‐functional epoxides derived from trans‐limonene oxide

The thiol‐ene reaction between trans‐limonene oxide (trans‐LO) and ethane‐1,2‐dithiol in the presence of triethylborane affords a bio‐based bis‐functional epoxide (bis‐trans‐LO). The crosslinking reaction of bis‐trans‐LO with branched polyethyleneimine (BPEI; M_n = 600; BPEI₆₀₀) at a feed ratio of bis‐trans‐LO/BPEI₆₀₀ = 57/43 (wt/wt) yields the corresponding network polymer with T_d10 (10% thermal decomposition temperature) of 304.7 °C in 98% yield. In contrast, negligible amounts of network polymer are obtained by the reaction of bis‐LO (bis‐functional epoxide derived from cis and trans‐LO) and BPEI₆₀₀ regardless of the feed ratio. The mechanical strengths as measured by direct tensile tests of the network polymers derived from bis‐trans‐LO and BPEI_600,1800 (M_n = 600 and 1800) were approximately 16 and 11 times higher than that of bis‐LO and BPEI₁₈₀₀, respectively. The tensile shear strengths of the metal‐to‐metal adhesive bonds induced by bis‐trans‐LO and BPEI_600,1800 were 9.5 and 14.1 MPa, respectively. DMA revealed that the storage modulus of the network polymer derived from bis‐trans‐LO and BPEI₁₈₀₀ in the rubber region was higher than that of the material prepared from bis‐LO and BPEI₁₈₀₀, indicating higher crosslink density of the bis‐trans‐LO/BPEI₁₈₀₀ system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2466–2473     

Extended Open-Chain Polyenides as Versatile Delocalized Anion Ligands for Metal Chain Clusters

Although small cyclic- and open-chain unsaturated hydrocarbon anions such as cyclopentadienide and open-chain pentadienide are used as the strongly electron-donating auxiliary ligands for metal complexes, more extended π-conjugated unsaturated hydrocarbon anions have rarely been used in coordination chemistry, despite their potential ability to serve as the multiply bridging π-ligands for metal clusters. This work reports isolation of metal chain clusters bearing the multi-dentate, open-chain extended unsaturated hydrocarbon anion ligands. The extended open-chain π-conjugated polyenyl ligands could effectively stabilize oxidized palladium chains, including an unprecedented [Pd₄]⁴⁺ chain.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

Multimode optical fiber demultiplexer-star coupler using a single gradient-index-rod lens and a multi-facet grating

An optical fiber multi-function device consisting of a single gradient-index-rod lens and a multi-facet blazed reflection grating is proposed to simultaneously realize functions of wavelength demultiplexing and optical signal distribution in a multimode optical fiber transmission system. We analyzed the demultiplexing characteristics and the tolerance of optical components using the ray trace method. This device can realize not only low loss optical signal distribution but also offers improved demultiplexing characteristics in comparison with the previously proposed demultiplexer-multiposition switch. The following characteristics are expected from the design using commercially available optical components: a working band of 0.64–0.88 μm, channel separation of 34–36 nm, 3 dB bandwidth of 27–28 nm, channel cross-talk of less than - 40 dB and minimum excess insertion loss of 0.9–2.1 dB.     

THE DESIGNS OF HIGH EFFICIENCY LAUNCHER OF QUASI-OPTICAL MODE CONVERTER FOR HIGH POWER GYROTRONS

A high efficiency launcher of quasi-optical (QO) mode converters for high power gyrotrons have been designed and tested. A helical cut launcher radiates the RF power via its straight cut onto the first phase correcting mirror. The launchers have been optimized for the TE_31.8 mode at 170 GHz and TE_22.6 mode at 110 GHz by numerically optimizing a launcher surface. The helical cut of the launcher has been optimized by taking the taper angle into account. Further more, the amplitude of the surface perturbation have been optimized for improved focusing in order to reduce the diffraction losses at the helical cut. Low power measurement shows a good agreement with the design. High efficiency characteristics of the design have also been calculated on the assumption of frequency downshift due to the thermal expansion of the cavity and stepwise frequency tuning by changing the operating mode. Besides, the possibility of high efficiency launcher for higher mode is discussed, and these results give the prospect to high efficiency long pulse gyrotrons.