A simple,rapid and sensitive method based on modified multiwalled carbon nanotube for preconcentration and determination of lead ions in aqueous media in natural pHs

In this study, multiwalled carbon nanotube (MWCNT) was modified by the pyridine group using a silane agent and characterized by infrared spectroscopy (IR), thermal analysis (TG/DTA), and elemental analysis (CHN) and scanning electron microscopy (SEM). The application of this sorbent was investigated in determination of lead ions in aqueous samples, using flame atomic absorption spectrometry (FAAS). Through this study, different parameters such as pH and sample flow rate on adsorption process and eluent concentration, volume and flow rate were optimized. The limit of detection (LOD), the relative standard deviation and the recovery of the method were 2 ng mL^?1, 1.3% and 99.7%, respectively. Two standard reference materials (NIST 1571 and NIST 1572) were used to verify accuracy of this method. Finally, the sorbent was successfully applied for extraction and determination of low levels of Pb(II) ions in aqueous samples.     

Elongation improvement in nano bainite steel obtained from plastically deformed primary austenite

ABSTRACT

Ausforming is being widely used to overcome the kinetics barrier in nanostructured bainitic steels and to enhance its practical industrial applications. It would also affect the microstructural characteristics and consequently the resultant mechanical performance. This article aims to investigate the tensile behaviour of nano bainite obtained from plastically deformed primary austenite at three different heat treatment stages. 10% of ausforming has been implemented and nanostructured bainite obtained after austempering at 300°C for 2, 4 and 6?h in salt bath furnaces. Results indicated that ausforming could successfully increase the volume fraction of bainite within the microstructure and refine the bainite packets sizes. Moreover, it has been demonstrated that higher mechanical stability of retained austenite and therefore more effective TRIP effect could be attained during the tensile test which consequently resulted in elongation improvement without deteriorating the strength properties. This claimed to be beneficial for materials performance during practical applications.     

Preparation of an efficient catalyst through injection of CuI on modified poly (styrene-co-maleic anhydride) and theoretical investigation of the structural and electronic properties of catalyst

A novel polymer supported [poly (styrene-co-maleic imide) (SMI)]Cu(I) nano-particles was prepared via in situ reaction of 4-amino-5-methyl-4H-1,2,4-triazole-3-thione with [poly (styrene-co-maleic anhydride)] (SMA) along with immobilization of CuI. These nano-particles were fully characterized by using scanning electron microscopy (SEM), energy dispersive spectroscopy analysis, Xray (EDAX), inductively coupled plasma (ICP) analysis, ¹H NMR and FT-IR techniques. Moreover, the structural and electronic features of metal–ligand interactions in the complex model of polymer-supported copper nanocatalyst were assessed using density functional theory calculations. The catalytic activity of these supported Cu(I) nonoparticles was examined in one of the classiest name reaction so–called “click reaction” which is coined K. B Sharpless for the regioselective synthesis of 1,2,3-triazole derivatives using a multicomponent reaction (MCR) involving benzyl halides, sodium azide and terminal alkynes in water as a green solvent. This heterogeneous catalyst showed excellent catalytic activity and was separated by simple filtration and was used at least in five consecutive runs without a significant decrease in its activity.     

Development of soot formation sub-model for Scania DC-9 diesel engine in the steady-state condition

Journal of Thermal Analysis and Calorimetry - The purpose of the present study is to provide a sub-model for the formation and oxidation of soot based on chemical kinetics for the DC-9 Scania...     

A microextraction procedure based on a task‐specific ionic liquid for the separation and preconcentration of lead ions from red lipstick and pine leaves

First, the extraction and preconcentration of ultratrace amounts of lead(II) ions was performed using microliter volumes of a task‐specific ionic liquid. The remarkable properties of ionic liquids were added to the advantages of microextraction procedure. The ionic liquid used was trioctylmethylammonium thiosalicylate, which formed a lead thiolate complex due to the chelating effect of the ortho‐positioned carboxylate relative to thiol functionality. So, trioctylmethylammonium thiosalicylate played the roles of both chelating agent and extraction solvent simultaneously. Hence, there is no need to use a ligand. The main parameters affecting the efficiency of the method were investigated and optimized. Under optimized conditions, this approach showed a linear range of 2.0–24.0 ng/mL with a detection limit of 0.0010 ng/mL. The proposed method was applied to the extraction and preconcentration of lead from red lipstick and pine leaves samples prior to electrothermal atomic absorption spectroscopic determination.     

Synthesis of new dyes containing double tetrazole groups for sensitization of TiO<Subscript>2</Subscript> nanoparticles in dye-sensitized solar cells

Di(1H-tetrazol-5-yl)methane is employed as a new electron acceptor group in the synthesis of two metal-free organic dyes containing triphenylamine donor group. Dye-sensitized nanocrystalline TiO₂ solar cell (DSSC) applying these novel dyes is constructed for consideration of their photovoltaic properties. The electronic properties of the dyes are also considered with the aid of theoretical calculations. The DSSC constructed from 4-(2,2-di(1H-tetrazol-5-yl)vinyl)-N,N-diphenylaniline (T1) shows a short-circuit photocurrent density of 13.38 mA cm^?2, an open circuit voltage of 578 mV, and a fill factor of 0.54, with a resulted solar energy-to-electricity conversion efficiency of 4.18% under simulated 1 sun irradiation (100 mW cm^?2). This result reveals that the dye with the di(1H-tetrazol-5-yl)methane anchoring group injects more electrons to the conduction band of TiO₂ in comparison with its analogs with single tetrazole ring in their anchoring group. It is found that in spite of a red-shift of the absorption spectrum resulted from the lengthening of the molecule, the dye with two di(1H-tetrazol-5-yl)methane groups gives lower performance than the dye with a single electron acceptor.     

Magnetically nano core–shell Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@Cu(OH)<Subscript>x</Subscript>: a highly efficient and reusable catalyst for rapid and green reduction of nitro compounds

Magnetically separable nano core–shell Fe₃O₄@Cu(OH)_x with 22 % Cu content was prepared by the addition of sodium hydroxide to a mixture of CuCl₂·2H₂O and nano Fe₃O₄ in water. Characterization of the impregnated copper hydroxide was carried out by X-ray fluorescence (XRF), X-ray diffraction (XRD) atomic absorption spectroscopy (AAS), scanning electron microscopy (SEM), value stream mapping (VSM) and Brunauer–Emmett–Teller (BET) analysis. The core–shell nanocatalyst exhibited the excellent catalytic activity toward reduction of various nitro compounds to the corresponding amines with NaBH₄. All reactions were carried out in H₂O (55–60 °C) within 3–15 min to afford amines in high to excellent yields. Reusability of core–shell Cu(OH)_x catalyst was examined 9 times without significant loss of its catalytic activity.     

Preparation of conductive,flexible and transparent films by in situ deposition of polypyrrole nanoparticles on polyethylene terephthalate

In this study polypyrrole (PPy) nanoparticles were deposited as a thin film on the modified surface of polyethyleneterephthalate (PET) by in situ chemical polymerization in the presence of sodium dodecylsulfate (SDS), sodium dodecylbenzenesulfonate (DBSNa) and mixture of them as the surfactant. The surface of PET was modified by KOH before deposition and was investigated for conductivity and adhesion of PPy nanoparticles to PET. Resulting conductive flexible films were characterized by UV–Vis spectroscopy, fieldemission scanning electron microscopy, contact angle measurements and four-point-probe technique for conductivity. Direct morphological observation (FESEM) and electrical measurements indicated that the morphology, conductivity and the nature of deposited PPy films depend on surfactant, surface modification of PET and monomer concentration. In optimized process condition, uniform conductive films of PPy were obtained with good adhesion to PET.     

Asymptotic Behavior of Quasi-Autonomous Expansive Type Evolution Systems in a Hilbert Space

We introduce the notion of almost expansive sequences and curves and study their ergodic and asymptotic properties in a Hilbert space H. We apply our results to study the asymptotic behavior of solutions to the quasi-autonomous expansive type evolution system (du/dt)(t) + f(t) ∈ Au(t) on [0, ∞).