MXene-based composite electrodes for efficient electrochemical sensing of glucose by non-enzymatic method

A recently discovered 2D transition titanium metal carbides also called as MXenes (Ti₃C₂T_x)-based nanocomposite was prepared with Cu₂O through wet precipitation technique, and these materials were further developed as the electrode for sensing glucose by chronoamperometry technique. The prepared MXene-Cu₂O (Ti₃C₂T_x-Cu₂O) nanocomposite was characterized by XRD, FTIR, UV–Vis spectroscopy, FE-SEM, EDAX, and Raman spectroscopy. Morphological studies of the composites revealed that the micro-octahedral shape of Cu₂O is distributed on the surface of MXene with size larger than bare Cu₂O. Further, the prepared composite material was fabricated as a sensing probe, and the electrochemical activities were examined by cyclic voltammetric analysis (CV) and chronoamperometric (CA) methods. From the CV and CA investigation, the current response was higher for the composite than the bare material (Cu₂O & MXene) in the presence of glucose. The amperometric investigation of MXene-Cu₂O composite for the detection of glucose shows a broad linear range (0.01–30 mM) with a sensitivity of 11.061/μAmM cm^?2 and a detection limit of 2.83 μM. Further, the fabricated sensor exhibits good selectivity with interfering species like NaCl, fructose, sucrose, urea, ascorbic acid, lactose, short response time, stability, good reproducibility, and compatibility with human serum sample. From the investigation, the prepared MXene-Cu₂O composite is a good candidate for the direct detection of glucose molecules and is also well suitable for clinical diagnosis.     

Development and investigation of the flexible hydrogen sensor based on ZnO-decorated Sb2O3 nanobelts

Hydrogen is regarded as the next-gen fuel for vehicles to avoid the emission of toxic gases, which needs a continuous monitoring of the concentration level. In the design of the H₂ sensor, especially of flexible type, a sensing layer will be blended, which affects the sensing performance of the device. Based on this concern, the present investigation is carried out to understand the effect of the bending angle toward the sensing performance of bare and ZnO (n-type)-decorated Sb₂O₃ (p-type) nanobelt–based sensors for hydrogen gas. The sensing element was prepared by the thermal chemical vapor deposition followed by the drop-casting method. Furthermore, the role of the zinc precursor (molar concentration—1 M–3 M) on the preparation of ZnO-decorated Sb₂O₃ nanobelts was studied. Various techniques were used to confirm the formation of ZnO-decorated nanobelts such as X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), and Fourier transform infrared spectroscopy (FTIR). From these analyses, 1 M concentration of the zinc precursor shows uniform distribution of nanoparticles over the surface of Sb₂O₃ nanobelts. However, agglomeration was observed when the concentration of the zinc precursor increases from 1 M to 3 M. Later, the prepared nanobelts were deposited on the OverHead Projector (OHP) sheet by the doctor blade method for sensing hydrogen gas at 100 °C at a concentration of 1000–3000 ppm. In addition to it, the effect of the substrate bending angle (0°, 45°, 60°, and 90°) was analyzed at a fixed concentration of H₂ gas (1000 ppm). From this study, it is clear that the highest sensing response was achieved for 1 M decorated nanobelts compared with bare as well as other concentrations because of uniform distribution of nanoparticles on the surface of nanobelts. Moreover, the prepared sample demonstrates better sensing performance with the bending of substrates, which suggests that the prepared sensor could be used for flexible electronic devices. The prepared nanobelts show a good H₂ gas–sensing response even with bending of the substrates. The work suggests that the prepared sensor is applicable for flexible electronic devices.