排序方式: 共有111条查询结果,搜索用时 15 毫秒
1.
2.
Donné AJ van Gorkom JC Udintsev VS Domier CW Krämer-Flecken A Luhmann NC Schüller FC;TEXTOR Team 《Physical review letters》2005,94(8):085001
Small-scale structures with high poloidal mode numbers (m=10-20) have been observed in the TEXTOR tokamak plasma with pulsed radar reflectometry and an electron cyclotron emission diagnostic, in conjunction with large 2/1 and 1/1 islands. The small islands have a peaked density profile, similar to that of the simultaneously observed large-scale 2/1 islands. This together with the observation that high-frequency density and temperature fluctuations are very pronounced near the X points of the large islands hints to a strongly perturbed magnetic topology around the X points. 相似文献
3.
Liang Y Koslowski HR Kelly FA Tokar MZ Loozen X Bertschinger G Biel W Finken KH Jakubowski MW Krämer-Flecken A Zimmermann O Lehnen M Sergienko G Wolf RC;TEXTOR Team 《Physical review letters》2005,94(10):105003
A significant influence of the dynamic ergodic divertor (DED) on the density limit in TEXTOR has been found. In Ohmic discharges, where without DED detachment normally arises at the density limit, a MARFE (multifaceted asymmetric radiation from the edge) develops when the DED is operated in a static regime. The threshold of the MARFE onset in the neutral beam heated plasmas is increased by applying 1 kHz ac DED at the high-field side. The theoretical predictions based on the parallel energy balance taking poloidal asymmetries into account agree well with the experimental observation. 相似文献
4.
为提高磁体系统安装精度,在 HL-2M 集成大厅建立 63 个基准点构成测量基准网,并利用激光跟
踪仪等高精度测量设备建立每个磁体的局部坐标系,测量特征点的局部坐标;基于测量基准网和公共测量点,采
用最佳拟合得到坐标转换矩阵,以此得到特征点在测量基准网的位置,指导磁体安装。完成安装后的中心柱同支
撑基础的同轴度为∅2.03mm;PF1~PF4 线圈安装标高偏差为±0.5mm,与中心柱的同轴度为∅2.60mm;PF5/6/7/8
线圈与中心柱的同轴度偏差小于∅3.00mm,标高偏差在[−1mm, 1mm]区间内。基于以上方法所得到的线圈安装精
度都满足设计需求。 相似文献
5.
6.
介绍了 HL-2M 装置冷却水系统的组成以及各子系统的循环流程、运行原理和运行参数。 相似文献
7.
为了测量 HL-2M 装置中的电子温度剖面分布,研制了一套扫频电子回旋辐射(SECE)系统。该系统
能够测量装置中心纵场大小在 1.4~2.2T 时的等离子体电子温度。采用扫频外差接收的方式,径向空间分辨达到
2.5cm,时间分辨达到 1ms。接收机前端的准光学系统采用两级金属反射镜的配置,系统能够接收的最小极向光
斑的直径为 1.5cm(波数 kθ<4.2rad·cm-1)。系统的频带范围覆盖 33~110GHz,采用 VCO 作为本振源,双边带混频
输出中频信号。后端首次采用高性能对数检波器解调中频,能直接对-70dBm 的微弱信号进行检测,输入-输出工
作区间的动态范围达到 45dB 以上。在实验期间,成功测量到了等离子体中电子逃逸以及回旋辐射产生的信号。 相似文献
8.
重点介绍了 HL-2M 装置的运行技术和初步的等离子体控制实验结果,包括等离子体放电方案设计、
线圈电流控制、击穿阶段零场匹配和等离子体电流以及位移的控制。为了降低放电运行风险,HL-2M 装置初始放
电采用了简化的放电方案,通过整定 PID 参数实现了线圈电流控制,在击穿阶段获得了 10V 以上的环电压和较大
范围的零场区域,成功实现等离子体击穿。最后,投入了等离子体电流和水平位移反馈控制算法,成功将等离子
体放电脉宽提升至 200ms 以上,且维持 Ip≥100kA 的时间超过了 100ms,上述结果表明 HL-2M 装置运行控制技术
得到了初步的检验。 相似文献
9.
通过数值计算评估了 HL-2M 装置磁测量传感器安装精度的要求,其中磁通环坐标(R, Z)的安装偏差
要求达到±2.0mm 以内,磁探针的(R, Z)偏差要求在±1.0mm 以内、角度偏差在±0.1°以内。定位安装采用高精度激
光跟踪仪和关节测量臂结合,设备定位精度在±0.3mm。根据不同种类的磁测量传感器的定位安装特点,优化设
计了包括磁通环、磁探针阵列、逆磁同心圆等的定位结构,将 HL-2M 磁测量传感器的安装精度控制到在±0.5mm
水平。 相似文献
10.
HL-2M 装置供电系统研制 总被引:2,自引:0,他引:2
为满足 HL-2M 装置的供电需求,须配套建设相应的供电系统。通过仿真计算 HL-2M 装置的总体供 电需求,考虑到 HL-2A 装置现有的供电系统设备,提出了兼顾 HL-2A 和 HL-2M 装置供电需求的总体配置方案。介绍了国内首台 300MVA 立式交流脉冲发电机组、磁体电源、高压电源和电源控制系统的研制情况。 相似文献