FeCoCrCuNi高熵合金裂纹及孔洞结构力学与微观构象演化机理的分子动力学模拟研究

本文采用分子动力学方法研究了FeCoCrCuNi高熵合金裂纹及孔洞模型结构在不同轴向拉伸应变速率下的力学与微观结构演化机理. 结果表明：应变速率越高FeCoCrCuNi裂纹结构对应更高的过冲应变和过冲应力，其主要原因是高拉伸速率会导致高强度的BCC结构及孪晶结构的生成，而BCC结构及孪晶结构的产生进而会抑制应力的下降，通过应力-应变曲线，可知FeCoCrCuNi裂纹模型在轴向应力作用下表现为塑性形变. 对于不同尺寸的孔洞FeCoCrCuNi裂纹模型的应力模拟与结构分析，可以得出：孔洞尺寸越大, FeCoCrCuNi裂纹结构对应的过冲应变和过冲应力越小，其主要原因是大尺寸的孔洞造成孔洞之间产生裂纹的，进而会影响这个材料的屈服应变和屈服强度.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

New di‐ and triorganotin(IV) carboxylates derived from a Schiff base: synthesis,characterization and in vitro antimicrobial activities

A new carboxylic acid, 2‐{[5‐(2‐nitrophenyl)furan‐2‐yl]methyleneamino}benzoic acid (HOBZ), has been produced by reacting 5‐(2‐nitrophenyl)furfural with 2‐aminobenzoic acid. Reactions of NaOBZ with organotin chlorides led to formation of [Me₃Sn(OBZ)] ( 1 ), [Bu₃Sn(OBZ)] ( 2 ), [Me₂Sn(OBZ)₂] ( 3 ) and [Bu₂Sn(OBZ)₂] ( 4 ). Complexes 1 , 2 , 3 , 4 have been characterized using elemental analyses and infrared, ¹H NMR, ¹³C NMR, ¹¹⁹Sn NMR and ¹¹⁹Sn Mössbauer spectroscopies. In the solid state, the OBZ ligands might coordinate to tin in an anisobidentate fashion via the carboxylate group. The in vitro antimicrobial activity of all compounds has been screened against the following fungi: Aspergillus niger, A. flavus, A. parasiticus, Penicillium citrinum, Candida dubliniensis, C. lusitaniae, C. albicans, C. tropicalis, C. parapsilosis and C. glabrata; and against the following bacteria: Staphylococcus aureus, Listeria monocytogenes, Bacillus cereus, Streptococcus sanguinis, Escherichia coli, Citrobacter frendii, Salmonella typhimurium and Pseudomonas aeruginosa. Complexes 2 and 4 exhibited higher biocide activity in comparison to 1 and 3 and to the control drugs nystatin and miconazole nitrate for the yeasts, and chloramphenicol and ampicillin for the bacteria. The biological activity of 2 was superior to that of 4 . In addition, the toxicity of HOBZ, NaOBz and 1 , 2 , 3 , 4 were determined using Chlorella vulgaris, revealing low toxicity of the complexes at MIC₅₀ concentrations. We also performed cell viability studies, using XTT assay, displaying no change in the mitochondrial function after 2–4 h of exposure of the microorganism to the complexes at MIC₅₀ concentrations. The butyl‐containing complexes 2 and 4 display greater lipophilicities than do the methyl analogues 1 and 3 , thereby endowing 2 and 4 with superior abilities to cross the microbe cell membrane, the possible mechanism of action. Copyright © 2015 John Wiley & Sons, Ltd.     

Characterization of new Pt(IV)–thiazole complexes: Analytical,spectral, molecular modeling and molecular docking studies and applications in two opposing pathways

New thiazole derivatives were synthesized and fully characterized, then coordinated with PtCl₄ salt. Also, the newly synthesized Pt(IV) complexes were investigated analytically (elemental and thermogravimetric analyses), spectrally (infrared, UV–visible, mass, ¹H NMR, ¹³C NMR, X‐ray diffraction) as well as theoretically (kinetics, modeling and docking). The data extracted led to the establishment of the best chemical and structural forms. Octahedral geometry was the only formula proposed for all complexes, which is favorable for d⁶ systems. The molecular ion peaks from mass spectral analysis coincide with all analytical data, confirming the molecular formula proposed. X‐ray diffraction (XRD) and scanning electron microscopy (SEM) allowed discrimination of features between crystalline particles and other amorphous morphology. By applying Gaussian09 as well as HyperChem 8.2 programs, the best structural forms were obtained, as well as computed significant parameters. Computed parameters such as softness, hardness, surface area and reactivity led us towards application in two opposing pathways: tumor inhibition and oxidation activation. The catalytic oxidation for CO was conducted over PtO₂, which was yielded from calcination of the most reactive complex. The success of catalytic role for synthesized PtO₂ was due to its particulate size and surface morphology, which were estimated from XRD patterns and SEM images, respectively. The antitumor activity was tested versus HCT‐116 and HepG‐2 cell lines. Mild toxicity was recorded for two of the derivatives and their corresponding complexes. This degree of toxicity is more favorable in most cases, due to exclusion of serious side effects, which is coherently attached with known antitumor drugs.     

水力劈裂问题的态型近场动力学建模

将态型近场动力学理论引入水力劈裂问题的模拟。构建了能反映岩土类材料准脆性断裂特征的态型近场动力学本构模型,并在物质点间相互作用力模型中加入等效水压力项,以实现在新生裂纹面上跟踪施加水压力。同时,考虑裂纹面间的接触,引入物质点间的短程排斥力作用,并设计了相应的接触算法。通过自编程序将模型和算法应用于含初始裂纹、不含初始裂纹以及含坝基软弱结构面的混凝土重力坝在高水头作用下的水力劈裂过程模拟,并与扩展有限元等模拟结果对比,验证了本文模型和算法的可行性和准确性。     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

Organotin(IV) complexes of NSAID,ibuprofen, X-ray structure of Ph3Sn(IBF), binding and cleavage interaction with DNA and in vitro cytotoxic studies of several organotin complexes of drugs

This study encompasses the synthesis and characterization of organotin(IV) derivatives of non-steroidal anti-inflammatory drug ibuprofen (IBF), viz. [(Me₃Sn)(IBF)] ( 1 ), [(Bu₃Sn)(IBF)] ( 2 ), [Ph₃Sn(IBF)] ( 3 ), {[Me₂Sn(IBF)]₂O}₂ ( 4 ) and [Bu₂Sn(IBF)₂] ( 5 ). The crystal structure of complex 3 , [Ph₃Sn(IBF)], indicates a highly distorted tetrahedral (td) geometry with anisobidentate mode of coordination of the carboxylate group with tin atom, and a similar structure has been proposed for other two triorganotin(IV) derivatives. Moreover, the DFT (density functional theory) calculation and other studies have verified a dimer distannoxane type of structure for complex 4 , {[Me₂Sn(IBF)]₂O}₂. Complex 5 has been found to exhibit a highly distorted octahedral geometry around the tin atom. To investigate the DNA binding profile of the synthesized complexes, viscosity measurement, UV–vis and fluorescence titrations were performed, which revealed an intercalative type of binding with DNA for IBF and complex 5 and external binding in case of the complexes 1 and 2 ; complexes 3 and 4 could not be studied owing to their insufficient solubility in tris buffer. Plasmid DNA fragmentation studies of IBF and complexes 1 , 2 and 5 indicate that they cleaved the pBR322 plasmid potentially. Further, the drugs IBF {2-[4-(2-methylpropyl)phenyl]propanoic acid}, MESNA (sodium 2-mercaptoethane-sulfonate), warfarin [2H-1-benzopyran-2-one,4-hydroxy-3-(3-oxo-1-phenylbutyl)], sulindac (2-{5-fluoro-1-[(4-methanesulfinylphenyl) methylidene]-2-methyl-1H-inden-3-yl}acetic acid) and their corresponding organotin(IV) complexes 1–19 (complexes 6–19 were synthesized/reported previously) were screened in vitro for cytotoxicity against human cancer cell lines viz. DU145 (prostate cancer), HCT-15 (colon adenocarcinoma), Caco-2 (colorectal adenocarcinoma), MCF-7 (mammary cancer), LNCaP (androgen-sensitive prostate adenocarcinoma) and HeLa (cervical cancer), through MTT reduction assay and the cause of cell death was investigated through acridine orange/ethidium bromide staining of cells and DNA fragmentation assay. The probable structure–cytotoxicity relationship is also discussed. The major role of apoptosis along with small necrosis was also validated by flow cytometry assay using annexin V–fluorescein isothiocyanate and propidium iodide analysis.     

一种经验型疲劳小裂纹扩展模型

金属材料疲劳寿命由裂纹萌生和裂纹扩展寿命两部分组成，其中对于萌生寿命中的小裂纹分析是精确描述裂纹萌生寿命的关键．而小裂纹在扩展过程中由于尺寸相对较小，导致传统线弹性断裂力学预测方法失效，需要对其进行改进，考虑裂纹尖端塑性区引起的残余压应力对小裂纹扩展速度的影响．本文针对此问题进行了初步分析，通过对塑性区引起的残余应力的量化，结合小裂纹门槛值特性，提出了一种经验型修正的小裂纹扩展模型，用于定量预测裂纹的萌生寿命．使用铝合金6082-T6缺口试样进行了疲劳实验，并与理论结果进行了对比，验证了所提模型的有效性．     

Oxotitanium(IV) complexes of some bis‐unsymmetric Schiff bases: Synthesis,structural elucidation and biomedical applications

A number of oxotitanium(IV) complexes of the type TiOL with bis‐unsymmetric dibasic tetradentate Schiff base (LH₂) containing ONNO donor atoms have been synthesized. Mono‐Schiff base (OPD‐HNP) was prepared by the condensation of 1:3 molar ratio of 2‐hydroxy‐1‐naphthaldehyde (HNP) with o‐phenylenediamine (OPD). Dibasic unsymmetric tetradentate diamine Schiff bases were prepared by the reaction of OPD‐HNP with 2‐hydroxyacetophenone, 2‐hydroxypropeophenone, benzoylacetone, acetylacetone and ethylacetoacetate. Further, titanylacetylacetonate was reacted with these ligands to obtain their metal complexes. On the basis of analytical and physiochemical data, the formation of complexes as TiOL was suggested having square pyramidal geometry. Quantum mechanical approach also confirmed this geometry. The assessment of the synthesized ligands and their complexes showed that some behave as good inhibitors of mycelial growth against selected phytopathogic fungi but weak inhibitors against some selected bacteria. A few of them also showed antioxidant properties.