单面柱局域共振声子晶体低频带隙特性分析及结构改进研究

基于有限元法对单面柱局域共振声子晶体进行带隙特性分析,研究了结构参数对该类型声子晶体的影响。结果表明:随着散射体高度的增加,单面柱声子晶体的第一完全带隙的起始频率逐渐降低,带宽逐渐增大;随着基板厚度的增大,单面柱声子晶体的起始频率逐渐升高,截止频率先增大后减小。并且在经典单面柱声子晶体的基础上,组合了两种新型的三组元单面柱声子晶体结构:嵌入式单面柱声子晶体(以下简称结构Ⅰ)和粘接式单面柱声子晶体(以下简称结构Ⅱ)。通过对其带隙特性的分析得出:这两种新结构与经典的单面柱声子晶体相比,都具有更低频的带隙,这对于低频减振降噪是非常有利的。本文的结果将对实际的工程应用提供一定的理论指导。     

Modulating Charge Carrier Efficient Separation Enabled by Lewis Base Modification in Paper-based Photoelectrochemical Sensor

The separation efficiency of charge carriers determines the analytical sensitivity of the paper-based photoelectrochemical sensor. Herein, the Lewis base modification strategy is proposed to promote the carrier separation through an in-situ ion exchange method. Firstly, three-dimensional paper-based hierarchically TiO₂ (PHT) arrays are prepared with the one-step hydrothermal method. With the aid of Lewis base, the photo-induced charge separation efficiency and the photocurrent signal are obviously increased. Ultimately, sensitive sensing of prostate specific antigen (PSA) is achieved and the linear range is 1 pg/mL–100 ng/mL with the detection limitation of 0.3 pg/mL.     

Photodeposition of CoOx nanoparticles on BiFeO3 nanodisk for efficiently piezocatalytic degradation of rhodamine B by utilizing ultrasonic vibration energy

Piezoelectric materials have received much attention due to their great potential in environmental remediation by utilizing vibrational energy. In this paper, a novel piezoelectric catalyst, CoO_x nanoparticles anchored BiFeO₃ nanodisk composite, was intentionally synthesized via a photodeposition method and applied in piezocatalytic degradation of rhodamine B (RhB) under ultrasonic vibration. The as-synthesized CoO_x/BiFeO₃ composite presents high piezocatalytic efficiency and stability. The RhB degradation rate is determined to be 1.29 h⁻¹, which is 2.38 folds higher than that of pure BiFeO₃. Via optimizing the reaction conditions, the piezocatalytic degradation rate of the CoO_x/BiFeO₃ can be further increased to 3.20 h⁻¹. A thorough characterization was implemented to investigate the structure, piezoelectric property, and charge separation efficiency of the CoO_x/BiFeO₃ to reveal the nature behind the high piezocatalytic activity. It is found that the CoO_x nanoparticles are tightly adhered and uniformly dispersed on the surface of the BiFeO₃ nanodisks. Strong interaction between CoO_x and BiFeO₃ triggers the formation of a heterojunction structure, which further induces the migration of the piezoinduced holes on the BiFeO₃ to CoO_x nanoparticles. The recombination of electron-hole pairs is retarded, thereby increasing the piezocatalytic performance greatly. This work may offer a new paradigm for the design of high-efficiency piezoelectric catalysts.     

On the Brauer p-dimension of Henselian discrete valued fields of residual characteristic p > 0

Let $(K,v)$ be a Henselian discrete valued field with residue field $\stackrel{?}{K}$ of characteristic $p>0$, and ${\text{Brd}}_p(K)$ be the Brauer p-dimension of K. This paper shows that ${\text{Brd}}_p(K)\ge n$ if $[\stackrel{?}{K}:{\stackrel{?}{K}}^p]=p^n$, for some $n\in \mathbb{N}$. It proves that ${\text{Brd}}_p(K)=\infty$ if and only if $[\stackrel{?}{K}:{\stackrel{?}{K}}^p]=\infty$.     

Piezoelectric Nanogenerator Based on Electrospun Cellulose Acetate/Nanocellulose Crystal Composite Membranes for Energy Harvesting Application

Nanogenerators, as the typical conversion of mechanical energy to electrical energy devices, have great potential in the application of providing sustainable energy sources for powering miniature devices. In this work, cellulose acetate/cellulose nanocrystal(CA/CNC) composite nanofiber membranes were prepared by electrospinning method and then utilized to manufacture a flexible pressure-driven nanogenerator. The addition of CNC not only increased the content of piezoelectric cellulose I crystallization but also strengthened the mechanical deformation of the nanofiber membranes, which could greatly enhance the piezoelectric performance of CA/CNC composite membranes. The CA/CNC composite nanofiber membrane with 20%(mass fraction) of CNC(CA/CNC-20%) showed optimal piezoelectric conversion performance with the output voltage of 1.2 V under the force of 5 N(frequency of 2 Hz). Furthermore, the output voltage of the CA/CNC-20% nanogenerator device exhibited a linear relationship with applied impact force, indicating the great potential in pressure sensors.     

Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

基于内聚力模型的快速荷载下CFRP-混凝土界面剪切剥离模拟

鉴于纤维增强复合材料(Fiber Reinforced Polymer, FRP)已在混凝土结构加固中普遍应用, 能有效提高结构的承载和变形能力. 为揭示动载作用下FRP-混凝土界面的剥离机理, 本文基于ABAQUS平台, 采用内聚力模型模拟CFRP-混凝土界面层, 实现了快速荷载下CFRP-混凝土界面剥离的高效模拟. 结果表明: CFRP表面应变在加载过程中由加载端向自由端方向传递, 随着加载速率的提高, 界面承载能力也随之提高; 界面峰值剪应力也存在显著的应变率效应; 模拟结果与试验结果基本吻合, 说明了新方法的有效性.     

梁柱简化模型在自立塔塔线体系动态响应中的适用性研究

对输电塔进行合理简化可以提高塔线体系动力学仿真的效率。本文给出自立塔梁柱简化模型的计算方法，并提出利用梁柱简化模型计算方法建立自立塔塔线体系整体模型，同时采用桁梁混合模型建立精细化塔线体系整体模型，对两种模型塔线体系静力特性及振型和固有频率等动力特性进行对比分析。以脱冰工况为例，采用生死单元技术将施加在输电线节点上的集中质量单元杀死来模拟脱冰，实现对塔线体系动力学响应的有限元模拟，研究塔线体系简化模型在动态响应中的适用性。结果表明，两种模型弯曲变形误差小，低阶的振型相同，固有频率值误差小，动力特性基本相同；脱冰工况下，自立塔节点位移和塔材内力时程曲线一致，在提高计算效率的情况下，能有效保证计算精度。     

以含碘氨基酸类激素为例刍议微量非金属元素在生物体内的作用机制

选取第五周期元素碘,结合多学科的研究方法论对含碘氨基酸类激素在生物体内的合成和分解代谢进行系统性分析。通过解析碘元素本身性质及其各个氧化态之间的转化,探讨碘元素在生物体内的作用机制,揭示自然界对物质代谢的精细调控。这一教学模式探索性地融入无机化学、元素有机化学、分子生物学、生物化学、生物物理学、化学生物学等一系列学科内容,旨在让学生在领悟生命科学内在规律,从而激发其科研及学习热情,并训练学生的类比思维和思辨能力。期对培养21世纪跨学科综合型人才的培养有所助益。     

“多才多艺”的铁元素*

铁在自然界中含量丰富,化学性质活泼,能够形成多种应用广泛的物质及材料,富有发展潜力。简述了铁元素的发现与性质,并重点介绍了铁的功能与应用。其中铁的应用主要围绕铁及其化合物在医学治疗、能源材料和环境保护领域所发挥的重要作用进行了阐述。