Dehydroaromatization of Methane with a Small Amount of Ethane for Higher Yield of Benzene

The dehydroaromatization of methane was investigated with addition of a few ethane. A high benzene yield was achieved at a higher space velocity. The addition of CO2 could improve the stability.     

反应条件对Ni-CaO-ZrO2催化剂上CH4-CO2重整反应及积炭的影响

用共沉淀法制备了Ni-CaO-ZrO₂催化剂,并将其用于CH₄-CO₂重整反应。考察了反应温度、空速和反应物配比对催化剂性能和积炭的影响。通过热力学计算和实验表征研究发现,反应条件对CH₄-CO₂重整反应结果和积炭有重要的影响。由于高温条件同时有利于CH₄裂解和碳物种的及时消除,升高温度可以提高催化剂的活性和稳定性。增大空速则使CH₄的转化率和消碳反应的速率均降低,导致积炭量增加。同时,反应物配比对催化剂表面的积炭量也有很大影响;稍高的CO₂/CH₄摩尔比有利于抑制CH₄-CO₂重整反应过程中的积炭。     

Pt/TiO_2催化剂上的氢—氧作用——Ⅱ. 程序升温还原和程序升温氧化研究

本文采用TPR、TPO技术分别考察了氧处理Pt/TiO_2上氧物种的还原行为和氢还原样品的氧化过程.TPR结果表明,表面含有活泼氧物种的Pt/TiO_2样品对氢很活泼,室温条件下可以吸附大量氢,并且这些吸附氢又可以在TPR过程中脱附.表面活泼氧物种与氢的反应温度在500—673K之间,当大于673K时,Pt/TiO_2继续耗氢,可能是氢与还原产生的表面Ti~(3+)离子进一步反应生成钛—氢物种,并向TiO_2体相扩散与TiO_2体相晶格氧发生反应.对于773K还原的Pt/TiO_2作品,室温吸附氧在TPD过程中可以与表面吸附氢反应;473K氧化处理可以消除表面的吸附氢,但并不能完全去除体相储氢;573K氧化处理则基本上恢复了原样品的氧化状态.不同温度氢还原处理的Pt/TiO_2样品在动态氧化过程(TPO)中,在300-600K温区,气相氧与样品上表面吸附氢和表面氧空位反应;在大于600K温区,氧主要与表面钛—氢物种发生反应,并向体相扩散,与体相氢发生反应.文中描述了气相氢、氧分别与Pt/TiO_2催化剂存在的氧或氢物种作用的形式.     

铕对Pt-Sn/γ-Al2O3重整催化剂性能的影响

研究了添加RE2O3(RE=Eu)的Pt-Sn/γ-Al2O3重整催化剂的反应性能. 研究结果表明添加稀土后, 催化剂的液收增加, 芳产增加, 积炭降低. 采用氢氧滴定(TPT)、程序升温还原(TPR)、吡啶红外光谱(IRS)、程序升温氧化(TPO)等对催化剂进行了物化表征. 结果表明, 催化剂中添加RE2O3之后, 催化剂中Pt的两种活性中心不变, 但改变了两种活性中心的相对比率, 低温活性中心降低, 高温活性中心增加; 稀土与Pt和Sn之间发生相互作用, 产生了电子效应, 使得它们的还原峰温向低温移动; 载体的酸量减少, 酸性减弱.     

EPR and Raman investigations into anionic redox chemistry of nanoporous 12CaO·7Al2O3 interacting with O2, H2 and N2O

EPR and Raman spectroscopy jointed with temperature-programmed reduction (TPR) and oxidation (TPO) were used to elucidate of the anionic redox processes occurring during the interaction of dioxygen, nitrous oxide and dihydrogen with nanoporous 12CaO·7Al₂O₃. The results showed that hydrogen and oxygen enter the mayenite cages following a dissociative pathway involving hydride, hydroxyl and peroxide intermediates, respectively. Generation and annihilation of the cage O ₂ ⁻ and O⁻ radicals upon oxidative and reductive treatments, confined to the near to the surface region, were found to be reversible. The key intermediates of this process were identified and a detailed mechanism of the surface and cage reactions was proposed.     

程序升温技术考察镍在钼基催化剂中的作用

利用程序升温技术考察了Ni促进的和未促进的钼基催化剂上进行噻吩加氢脱硫（HDS）,苯、环己烯的程序升温加氢反应（TPH）,通过对硫化态催化剂的程序升温还原（TPR）、程序升温脱附（TPD）以及程序升温氧化（TPO）等表征,发现添加№之后调变了Mo—S键合行为,使得催化剂在反应过程中易于形成或者维持更多的S配位空位数目,...     

TPR/TPO characterization of cobalt–silicon mixed oxide nanocomposites prepared by sol–gel

Cobalt–silicon mixed oxides with Co/Si ratio of 10/90 (10Co), 20/80 (20Co) and 30/70 (30Co) were prepared by a modified sol–gel method. The materials treated in air at 400 and 600 °C were characterized by SEM and TPR/TPO techniques. TPR measurements showed that in all samples only a fraction of Co was present as Co₃O₄ and as amorphous silicate and was reducible by H₂ within 800 °C, while a part was not reducible under TPR conditions. The fraction of Co not reducible decreased with increasing Co content. A TPO/TPR cycle gave rise to an increase of the fraction of not reducible Co.     

Crosslinked Polyvinylnorbornene‐Based Membranes as a New Class of Solvent‐Resistant Nanofiltration Membranes

Solvent resistant nanofiltration (SRNF) has received increasing attention since the turn of the century within energy‐ and waste‐efficient unit processes. This work explores the synthesis and characterization of crosslinked polynorbornenes for SRNF. A series of polyvinylnorbornene thin‐film composite membranes with increasing degree of crosslinking were prepared and tested for their SRNF performance in heptane, chloroform, and toluene. Sudan Black B (457 g mol^?1) was used as the solute. Then, 99% retention was achieved in heptane, 86% in chloroform, and 75% in toluene. It was further shown that the permeance and retention can be fine‐tuned in these solvents by controlling the extent of crosslinking. This work thus introduces the crosslinking of polynorbornenes as a promising material route for SRNF. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1593–1600     

Acetylene hydrogenation on SiO2 supported gold nanoparticles

Acetylene hydrogenation has been investigated on 1.8 wt.% Au(I)/SiO₂ and 1.9wt.% Au(II)/SiO₂ catalysts prepared by fixation of Au sol to SiO₂ (Aerosil 200). The mean particle size measured by TEM is 3.7 and 6.1 nm, respectively. For the sake of comparison a 2.1 wt.% Au/TiO₂ sample was prepared by deposition-precipitation (DP) technique (mean particle size of Au is 3.3 nm). Transformation of acetylene was measured at 5 K/min ramp rate with gas mixtures containing the reactants at H₂/C₂H₂=2 and 70 ratios. The C₂H₂ content of the gas mixture was 0.11% (0.11 kPa C₂H₂). The activity sequence at 423 K was: Au/TiO₂>Au(I)/SiO₂≫Au(II)/SiO₂. Both the partial pressure of hydrogen and the temperature significantly affect the activity (acetylene conversion) and ethylene selectivity. Above 500–550 K over-hydrogenation (ethane formation) and hydrogenolysis (methane formation) decrease the ethylene selectivity. Faster deactivation and larger amount of deposit was observed on Au/TiO₂ than on Au(I)/SiO₂. A reaction scheme is proposed suggesting formation of sigma bonded intermediates as sp carbon hybridises to sp² and sp³.     

Characterization of carbon nanotubes and analytical methods for their determination in environmental and biological samples: A review

In the present paper, a critical overview of the most commonly used techniques for the characterization and the determination of carbon nanotubes (CNTs) is given on the basis of 170 references (2000–2014). The analytical techniques used for CNT characterization (including microscopic and diffraction, spectroscopic, thermal and separation techniques) are classified, described, and illustrated with applied examples. Furthermore, the performance of sampling procedures as well as the available methods for the determination of CNTs in real biological and environmental samples are reviewed and discussed according to their analytical characteristics. In addition, future trends and perspectives in this field of work are critically presented.