超声波多普勒实验仪

基于多普勒效应原理,分别测得波源的频率和发生相对运动时观测到的频率即可分析出物体相对运动的速度.实验仪以单片机为测控系统核心实现超声波多普勒效应演示实验及速度测量并提供了具体的设计方案与实验结果.同时单片机赋予了仪器以软件为核心的技术特点,具有重塑性与可扩展性.     

EFFECT OF DAMAGE EVOLUTION ON POISSON’S RATIO OF CONCRETE UNDER SULFATE ATTACK

Experimental results about concrete under sulfate attack are summarized,which include the variation of mass density of samples and velocity of ultrasonic wave propagating in samples.The evolution damage is analyzed in terms of the experimental results,and close attention is paid to the effect of damage evolution on Poisson’s ratio.This study shows that Poisson’s ratio is significantly affected by the concentration of solution and water-cement ratio.Poisson’s ratio of concrete changes very little when the water-cement ratio is selected as 0.6 or 0.8,so that such change may be neglected.If water-cement is 0.4,however,the Poisson’s ratio of the sample significantly changes.When the concrete sample of 0.4 water-cement ratio is immersed in sodium sulfate solution of 8% concentration for 285 days,Poisson’s ratio increase 10.14% compared with its initial value.There exist a sensitive region and a non-sensitive region for the change rate of Poisson’s ratio with respect to corrosion time.The change rate of Poisson’s ratio monotonously decreases with corrosion time in the sensitive region;in the non-sensitive region,the change rate of Poisson’s ratio is almost equal to zero.     

某矿山金矿石样品加工及分析方法优化研究

某矿山金矿石样品中存在中粗颗粒金,颗粒金的存在将对分析样品的均匀性和代表性产生影响。通过棒磨、密封粉碎及盘磨等方式研究,选择出最优的样品加工方式,同时通过分析方法比对,选择出最优的样品分析方法。实验确定金矿石采用圆盘细碎机加工至样品粒度不大于0.074 mm,混匀后即获得分析试样。分析试样经王水消解后采用泡沫吸附进行富集,火焰原子吸收光谱法测定。通过研究,取得最优的金矿样品加工和分析方案,为某矿山提供了高品质的金储量评估数据。     

船用超声液位传感器的分析与设计

介绍了一种船用某型超声液位传感器的基本结构和工作原理。在对脉冲式超声探头的轴向声压分布特点及其声透射强度分析研究的基础上,给出了该传感器的超声信号发射端与接收端之间距离d和压电晶片保护膜的壁厚δ值的确定方法。最后设计了一套超声液位传感器性能测试实验平台,对上述理论研究结论进行了实验验证。     

Analysis of ultrasonic guided waves propagating in long bones and cortical thickness based on time-frequency methods

The ultrasonic signals in long bones contain multiple guided modes which are mutual superposed.The velocities of guided waves in long bones are very sensitive to cortical thickness (CTh).In this paper,Hilbert-Huang transform(HHT) was proposed to analyze multi-mode guided waves,which can decompose superposed waves into many independent modes.Then the group velocity of each mode was obtained at corresponding frequency,which was compared with the results of short time Fourier transform(STFT).The CTh was also obtained by comparing with the theoretical calculation.The results showed that the experimental determined thickness was in agreement with the actual CTh,indicating that measuring the velocity of the guided mode can be used to estimate the CTh.The HHT is an effective method to identify multimode guided waves.     

Characterizing the properties of ultrasonics propagating on the surface of materials with defect by Laser-ultrasonics method

A laser ultrasonics method is used to characterize the propagation properties of surface wave traveling on the surface of materials with sub-surface defect in 2D.Linear and nonlinear propagation properties of ultrasonics caused by the defects have been detected in experiment. A theoretical model is proposed and used to study the linear and nonlinear properties of ultrasonics caused by the defect.The numerical results indicate that the nonlinear ultrasonic wave will be excited when a finite amplitude ultrasonics propagates on the surface of materials with sub-surface defect.The theoretical analysis confirms that the nonlinear wave is caused by the "clapping"of the interface of defect instead of the mode conversions of ultrasonics.     

Dynamical process of cavitation bubble adsorbed in gold nanoparticle under combined irradiations of laser and ultrasound

Under combined irradiation of laser and ultrasound,cavitary bubbles are generated on the surface of gold nanoparticle.The laser-induced thermal effect,ultrasonic cavitation effect and the synergistic effect of laser and ultrasound are studied by means of the investigation of the dynamical process for the vibration of the cavitation bubble,with different external conditions such as laser power,ultrasound intensity,etc.It is found that dynamical process of the cavitation bubble can be modified by the irradiation of laser or ultrasound.The enhancement of laser power can increase the critical radius of the cavitation bubble,while that of ultrasound may intensify the vibration.Cavitation bubble may become more stable due to the synergistic effect of laser and ultrasound.It is also found that variation of the coupling between laser and ultrasound can affect synergistic effect.     

晶粒尺寸对气相沉积薄膜磁取向生长的影响研究

为了研究强磁场下薄膜取向生长规律,采用真空蒸发气相沉积法分别制备了不同磁场方向生长的Zn和Bi薄膜.XRD结果发现磁化率差异较小的Zn薄膜在4T时产生了明显的取向生长,而磁化率差异较大的Bi薄膜在5T磁场强度还没有发生取向生长.SEM结果显示Zn薄膜和Bi薄膜晶粒尺寸上有明显的差别,利用Zn薄膜在4T磁场下的取向建立晶粒尺寸和取向生长的对应关系,提出薄膜发生取向时晶粒的磁化能须大于热能kT的420倍.薄膜是否发生取向生长取决于三个因素:薄膜单个晶粒的大小V,材料不同晶向的磁化率差异Δ关键词： 强磁场 磁取向 薄膜生长 材料电磁加工     

聚乙烯醇/明胶/纳米羟基磷灰石复合材料热塑加工性能研究

结合固相剪切碾磨技术(S3M),以胶原纤维(Col)在熔融挤出过程中原位降解成明胶(Gel),通过Gel与聚乙烯醇(PVA)分子间形成氢键复合增塑PVA,改善聚乙烯醇/纳米羟基磷灰石(PVA/n-HA)复合材料的热塑加工性能.采用扫描电子显微镜(SEM)、傅里叶变换红外光谱仪(FTIR)、示差扫描量热仪(DSC)、热重分析仪(TGA)、X射线衍射仪(XRD)和高压毛细管流变仪等研究了复合材料的结构与热塑加工性能.结果表明,通过S3M技术实现了n-HA在PVA基体中的均匀分散;FTIR表明Gel与PVA间形成了氢键作用和部分接枝反应;Gel和PVA分子间的氢键作用使PVA/Gel/n-HA复合材料的初始分解温度提高到287.6℃,改善了PVA的热稳定性,PVA的结晶度由纯PVA的58.2%降低到复合材料中的24.5%,使其熔点降低至130.5℃,拓宽了PVA/n-HA复合材料的加工范围,获得超过140 K的热塑加工窗口.Gel有效降低了PVA/nHA复合材料表观黏度,改善了PVA/n-HA复合材料的热塑加工性能.     

阴离子聚合PA6与苎麻纤维复合反应中的阻聚与变色机理的研究

通过浇注成型的方法研究并发现了苎麻纤维与阴离子聚合尼龙6(APA-6)反应加工过程中严重的阻聚和变色问题.为了分析阻聚和变色的机理并寻找解决方案,选取了3种不同的引发剂(氢氧化钠、己内酰胺钠盐和己内酰胺溴化镁)分别与微晶纤维素(MCC)在150℃的真空条件下反应.然后分别采用傅里叶变换红外光谱、原子吸收光谱、X-射线衍射和核磁共振波谱表征了引发剂和MCC反应前后的变化.结果证明,阻聚和变色的机理是在强碱性和高温条件下,纤维素发生了剥皮反应,产生的副产物又极易与引发剂反应,因此导致APA-6中起引发作用的己内酰胺阴离子被消耗,从而使得聚合反应终止.另外,由于己内酰胺溴化镁(C1)的低活性和弱碱性,使得剥皮反应很大程度的降低,进而避免了引发剂阴离子的消耗,从而使得阻聚和变色问题得到明显改善,最终实现了通过反应加工的方法制备APA-6与苎麻纤维复合材料的目的.