Characteristics of black carbon aerosol in Jiaxing,China during autumn 2013

We conducted measurements of black carbon（BC） aerosol in Jiaxing,China during autumn from September 26 to November 30,2013.We investigated temporal and diurnal variations of BC,and its correlations with meteorological parameters and other major pollutants.Results showed that hourly mass concentrations of BC ranged from 0.2 to 22.0 μg/m³,with an average of 5.1 μg/m³.The diurnai variation of BC exhibited a bimodal distribution,with peaks at 07:00 and 18:00.The morning peak was larger than the evening peak.The mass percentages of BC in PM_2.5 and PM₁₀ were 7.1%and 4.8%,respectively.The absorption coefficient of BC was calculated to be 44.4 Mm^-1,which accounted for 11.1%of the total aerosol extinction.BC was mainly emitted from local sources in southwestern Jiaxing where BC concentrations were generally greater than 11 μg/m³ during the measurement period.Correlation analysis indicated that the main sources of BC were motor vehicle exhaust,and domestic and industrial combustion.     

Mass and isotopic concentrations of water-insoluble refractory carbon in total suspended particulates at Mt.Waliguan Observatory(China)

Mass concentration and isotopic values δ¹³C and ¹⁴C are presented for the water-insoluble refractory carbon（WIRC） component of total suspended particulates（TSP）,collected weekly during 2003,as well as from October 2005 to May 2006 at the WMO-GAW Mt.Waliguan（WLG） site.The overall average WIRC mass concentration was（1183±120）ng/m³（n = 79）,while seasonal averages were 2081 ±1707（spring）,454±205（summer）,650±411（autumn）,and 1019±703（winter） ng/m3.Seasonal variations in WIRC mass concentrations were consistent with black carbon measurements from an aethalometer,although WIRC concentrations were typically higher,especially in winter and spring.The δ¹³C PDB value（-25.3 ± 0.8）%.determined for WIRC suggests that its sources are C₃ biomass or fossil fuel combustion.No seasonal change in δ¹³C PDB was evident.The average percent Modern Carbon（pMC） for ¹⁴C in WIRC for winter and spring was（67.2 ± 7.7）%（n = 29）.Lower pMC values were associated with air masses transported from the area east of WLG,while higher pMC values were associated with air masses from the Tibetan Plateau,southwest of WLG.Elevated pMC values with abnormally high mass concentrations of TSP and WIRC were measured during a dust storm event.     

Integral closure of a quartic extension

Let R be a Noetherian unique factorization domain such that 2 and 3 are units,and let A=R[α]be a quartic extension over R by adding a rootαof an irreducible quartic polynomial p(z)=z4+az2+bz+c over R.We will compute explicitly the integral closure of A in its fraction field,which is based on a proper factorization of the coefficients and the algebraic invariants of p(z).In fact,we get the factorization by resolving the singularities of a plane curve defined by z4+a(x)z2+b(x)z+c(x)=0.The integral closure is expressed as a syzygy module and the syzygy equations are given explicitly.We compute also the ramifications of the integral closure over R.     

高浓铀金属临界装置缓发中子有效份额测量

缓发中子有效份额βeff是反应堆动态特性的重要参数,也是相对反应性与绝对反应性之间的转换桥梁,对于以反应性作为宏观参数的检验工作具有重要意义。测量采用基于Rossi-α方法的Nelson数法开展了快临界装置βeff的实验研究。通过采用铅屏蔽、更薄的6Li玻璃闪烁体、脉冲幅度甄别三种措施,降低了γ射线对测量的影响。实验中测量了反应堆从-60￠到缓发临界之间的7个状态,最终测量得到βeff值为0.006 66,不确定度为7.88%;与理论计算数值偏差为2.15%。测量结果与理论值符合良好,表明了测量方法的有效性。     

考虑非结构性的多级生产流程调度方法

针对智能化柔性制造过程存在的再制造过程,对中小型设备生产车间及其仓储转运的模型构建、分析方法、以及参量相关性提出了新的解决思路.为了最大限度的减少建设周期、合理化投资成本、以及优化生产流程,建立了考虑非结构性的多级生产流程的数学模型,以完成度、完工时间和调度频次为目标函数分析生产要素间的相关性.实验结果表明,融合再加工过程的智能化柔性制造单元中,生产要素为非线性相关,个别要素具备对称性,为实际工况中的生产改进及优化提供了一定理论基础.     

Small bandgap non-fullerene acceptor enables efficient PTB7-Th solar cell with near 0 eV HOMO offset

Three small bandgap non-fullerene(SBG NFAs) acceptors,BDTI,BDTI-2 F and BDTI-4 F,based on a carbon-oxygen bridged central core and thieno[3,4-b]thiophene linker,end-capped with varied electronwithdrawing terminal groups,were designed and synthesized.The acceptors exhibit strong absorption from 600 nm to 1000 nm.The optimal device incorporating designed NFA and PTB7-Th polymer donor achieves a power conversion efficiency of 9.11% with near 0 eV HOMO offset.The work presents a case study of efficient non-fullerene solar cells with small HOMO offsets,which is achieved by blending PTB7-Th with fine-tuned SBG acceptor.     

g-C3N4催化石墨化碳质材料的制备及光催化性能研究

通常采用以氢氧化物作为造孔剂,过渡金属硝酸盐或氯化物作为石墨化催化剂的传统两步法策略制备多孔石墨化碳材料。然而制备过程中多涉及有毒和腐蚀性试剂,且多步骤的过程耗时较长。本文以双氰胺为原料通过热缩聚反应得到g-C₃N₄,采用高铁酸钾为催化剂一步法实现g-C₃N₄的同步碳化-石墨化,并研究其光催化性能。与传统的两步法相比,该方法耗时少、效率高、无污染。与初始的g-C₃N₄材料相比,石墨化g-C₃N₄衍生碳质材料不仅显著改善了可见光的吸收,而且大大增强了光催化活性。研究了不同石墨化温度对g-C₃N₄衍生碳质材料在可见光下降解甲基橙溶液的影响。700 ℃下制备的衍生碳质材料的降解率为12.4 mg/g。光电化学测试结果表明,多孔g-C₃N₄衍生碳质材料的光生载流子密度、电荷分离和光电流(提高了5.4倍)均得到显著提高。因此,该简便、灵活方法为提高g-C₃N₄衍生碳质材料的吸附和光催化性能提供了一种有前景的、高效的途径。     

Atomic-scale simulations for lithium dendrite growth driven by strain gradient

Dendrite formation is a major obstacle, e.g., capacity loss and short circuit, to the next-generation high-energy-density lithium (Li)-metal batteries. The development of successful Li dendrite mitigation strategies is impeded by an insufficient understanding in Li dendrite growth mechanisms. The Li-plating-induced internal stress in Li-metal and its effects on dendrite growth have been widely studied, but the underlying microcosmic mechanism is elusive. In the present study, the role of the plating-induced stress in dendrite formation is analyzed through first-principles calculations and ab initio molecular dynamic (AIMD) simulations. It is shown that the deposited Li forms a stable atomic nanofilm structure on the copper (Cu) substrate, and the adsorption energy of Li atoms increases from the Li-Cu interface to the deposited Li surface, leading to more aggregated Li atoms at the interface. Compared with the pristine Li-metal, the deposited Li in the early stage becomes compacted and suffers the in-plane compressive stress. Interestingly, there is a giant strain gradient distribution from the Li-Cu interface to the deposited Li surface, making the deposited atoms adjacent to the Cu surface tend to press upwards with perturbation and causing the dendrite growth. This provides an insight into the atomicscale origin of Li dendrite growth, and may be useful for suppressing the Li dendrite in Li-metal-based rechargeable batteries.     

数据驱动计算力学研究进展

以数字孪生、人工智能为核心的大数据理念正深刻影响着第四次工业革4 命，数据驱动计算力学在此背景下应运而生并展现勃勃生机。与此同时，航5 空航天等尖端工业领域对高性能材料与结构的先进制造与安全评估提出了更6 严峻的挑战，经典计算力学已很难实现成倍缩短产品研发周期、实时跟踪产7 品信息并提供解决方案的目标。因此，发展面向高性能材料与结构的数据驱8 动计算力学正当其时且刻不容缓。本文拟通过梳理数据驱动计算力学的部分9 研究现状，探讨并浅析数据驱动计算力学的发展趋势.     

稳定分层湍流中逆梯度输运的关联分析研究

本文采用关联分析方法研究了稳定温度分层湍流中的结构特性、输运特性，以及热量、动量逆梯度输运现象的尺度效应及其参数演化．首先采用大涡模拟方法对稳定分层湍流中的结构特性和输运特性进行了分析，将逆梯度输运发生的时间尺度作为已知条件，结合关联量分析方法在波数空间中的解析解，对逆梯度输运现象的尺度效应进行了分析研究．结果发现，稳定分层强度较大的流动中发生垂向热量及动量逆梯度输运现象，发生的结构尺度与关联分析所发现垂向热量、动量逆梯度输运的波数形成了呼应．随着分层强度增加，热量、动量的输运强度均受抑制，与逆梯度输运关联的流场结构尺度减小，同样的效应也发生在流场结构向下游演化的过程中．