Superspace groups and superstructures: NbS3

The application of superspace groups to short-period superstructures is considered. For niobium tri-sulfide this is worked out in detail. It is shown that in that case the superspace group provides more symmetry then given by the space group of the supercell. Its consequences for the structure, the diffraction pattern and tensor-properties are discussed.     

Modeling and numerical simulation of the resistance spot welding of zinc coated steel sheets using rounded tip electrode: Analysis of required conditions

This paper investigates the essential conditions to improve the accuracy of a resistance spot welding computational study of advanced zinc coated steel sheets using rounded tip electrode. An experimental analysis is performed to highlight the required considerations for a suitable simulation. A sequential Electrical-Thermal-Metallurgical and Mechanical (ETMM) finite element analysis with appropriate precautions of the contact conditions enables to accurately simulate the nugget development during the welding. A critical smooth evolution of the contact radius is required. A fine meshing with an interfacial mesh size of at least 0.05 × 10⁻³ m combined with a coupling time step of 0.0025 s between the electrical-thermal-metallurgical and the mechanical analysis allows a regular incrementation of the contact radius, without burdening the time computing. Accurate values of the contact resistance depending on the interfacial pressure and temperature are essential for a good simulation of the nugget size. The ETMM calculation is successfully extended to the simulation of the welding of a typical two sheets assembly.     

1.3 GHz超导腔磁通排出效应研究

设计并搭建了一套高精度的磁场测量和补偿系统,并结合中国科学院高能物理研究所(IHEP)的2K超导腔垂直测试平台对1.3 GHz单加速间隙超导腔的磁通排出效应开展了实验研究:利用研制的磁场测量和补偿系统能够精密地测量超导腔赤道位置磁场,并能够将磁场补偿至小于5.0×10-8 T;并对超导腔不同表面温度梯度下的磁通排出效应进行了测量分析;对钉扎了磁场的超导腔进行了射频性能测试,研究了超导腔电阻对磁通钉扎的敏感度,以及在不同电场梯度下超导腔的表面电阻变化情况。结果表明,研制的高精度磁场测量和补偿系统能够满足超导腔磁通排出研究的需求;高的超导腔表面温度梯度有利于磁通的排出;磁通钉扎电阻的敏感度随着加速电场梯度的增加而增大,导致超导腔的性能下降。此实验研究也为后续超导腔的研制奠定了一定基础。     

Effect of cooling rate on microstructure of friction-stir welded AA1100 aluminum alloy

In this work, the microstructural changes occurring during cooling of friction-stir welded aluminum alloy AA1100 were evaluated. To this end, friction-stir welding (FSW) was performed in a wide range of cooling rates of 20–62 K/s and the evolved microstructures were studied by using electron backscatter diffraction. Below 0.6 T_m (T_m being the melting point), the stir zone material was found to experience no significant changes during cooling. At higher FSW temperatures, however, notable changes occurred in the welded material, including grain growth, sharpening of texture, reduction of the fraction of high-angle boundaries and material softening.     

中国聚变工程实验堆水冷包层钢构件流道成形控制研究

针对CFETR水冷包层流道钢构件热等静压制备时易变形压塌问题，利用单轴扩散焊设备开展了焊接工艺参数优化试验。在此基础上，重新设计了流道焊接界面位置和尺寸，用两步热等静压扩散焊法制备出了流道变形可控的平板型第一壁钢构件模块。优化试验表明，低活化钢试样的固相扩散焊温度需高于950℃，焊后经过760℃/60min回火热处理试样力学性能可以得到有效回复。     

Growth of large La2−xSrxCuO4 single crystals using tilting-mirror-type infrared heating image furnace

Large single crystals of La_2−xSr_xCuO₄ (LSCO) high-T_c superconductors were grown by the infrared heating floating zone (IR-FZ) method using a tilting-mirror-type image furnace. The maximum diameter of the LSCO crystals increased to 10 mm in the tilting-mirror-type image furnace from 6 mm in the conventional image furnace. CuO rich feeds were required for the crystal growth using the tilting-mirror-type image furnace to compensate for the lack of CuO caused by the significant evaporation of CuO during the growth. The evaporation of CuO was affected by the tilting angle of the mirrors of the image furnace and by feed diameter. The optimized growth conditions were as follows: mirror tilting angle, 20°; feed diameter, 10 mm∅; and feed composition 50.7 mol% CuO.     

Waiting times of entangled electrons in normal–superconducting junctions

We consider a normal–superconducting junction in order to investigate the effect of new physical ingredients on waiting times. First, we study the interplay between Andreev and specular scattering at the interface on the distribution of waiting times of electrons or holes separately. In that case the distribution is not altered dramatically compared to the case of a single quantum channel with a quantum point contact since the interface acts as an Andreev mirror for holes. We then consider a fully entangled state originating from splitting of Cooper pairs at the interface and demonstrate a significant enhancement of the probability to detect two consecutive electrons in a short time interval. Finally, we discuss the electronic waiting time distribution in the more realistic situation of partial entanglement.     

Theoretical stability,thin film synthesis and transport properties of the Mon +1GaCn MAX phase

The phase stability of Mo_{n +1}GaC_n has been investigated using ab‐initio calculations. The results indicate stability for the Mo₂GaC phase only, with a formation enthalpy of –0.4 meV per atom. Subsequent thin film synthesis of Mo₂GaC was performed through magnetron sputtering from elemental targets onto Al₂O₃ [0001], 6H‐SiC [0001] and MgO [111] substrates within the temperature range of 500 °C and 750 °C. High structural quality films were obtained for synthesis on MgO [111] substrates at 590 ºC. Evaluation of transport properties showed a superconducting behavior with a critical temperature of approximately 7 K, reducing upon the application of an external magnetic field. The results point towards the first superconducting MAX phase in thin film form. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Measurement of micro weld joint position based on magneto-optical imaging

In a laser butt joint welding process,it is required that the laser beam focus should be controlled to follow the weld joint path accurately.Small focus wandering off the weld joint may result in insufficient penetration or unacceptable welds.Recognition of joint position offset,which describes the deviation between the laser beam focus and the weld joint,is important for adjusting the laser beam focus and obtaining high quality welds.A new method based on the magneto-optical(MO)imaging is applied to measure the micro weld joint whose gap is less than 0.2 mm.The weldments are excited by an external magnetic field,and an MO sensor based on principle of Faraday magneto effect is used to capture the weld joint images.A sequence of MO images which are tested under different magnetic field intensities and different weld joint widths are acquired.By analyzing the MO image characteristics and extracting the weld joint features,the influence of magnetic field intensity and weld joint width on the MO images and detection of weld joint position is observed and summarized.