On the physical adsorption of gases on carbon materials from molecular simulation

In this paper we present a series of work covering a range of aspects relating molecular simulation to experiment. The importance of surface mediation type effects to the adsorption of simple and complex gases is demonstrated. Coupled with the adsorption of simple gases is their projection area when used for surface area determination. The pressure dependence of a projection area is demonstrated for argon at 77 and 87.3 K. A simple model is used to account for the degree of graphitisation of a surface is demonstrated and used to account for the isosteric heat behaviour of non-graphitised carbon blacks. Turning from surfaces to porous solids, an alternative treatment of experiment data (either sub or super critical) is presented that avoids the ambiguity of excess amounts adsorbed. Using this method one is able to obtain pore size distributions and amounts adsorbed without relying on such things as helium expansion volumes. Since this type of method is usually applied to composite solids we also demonstrate the correct method for calculating the heat of adsorption using independent sets of simulations. The final topic covered in this paper is an example of the information that can be gained from the heat capacity of an adsorbed phase.     

Studies on the phase properties of lyotropic liquid crystals of Brij35/sodium oleate/oleic acid/water system:By means of polarizing microscope,SAXS,~2H-NMR and rheological methods

The pseudo-quaternary phase diagram of Brij35/sodium oleate/oleic acid/water systems has been investigated, and the liquid crystal area has been identified, which covers about two thirds of the whole phase diagram. The liquid crystal structure and behavior have been also studied by using polarizing texture, small angle X-ray scattering, 2H-NMR and rheometer etc. The result shows that when the composition of the system changes along the line of AA′ in this large liquid crystal region, the structural change is cubic→cubic/lamellar→lamellar→lamellar/hexagonal→hexagonal. Meanwhile, we made the first attempt of systematic study of the rheological properties of the above system. The lattice constants of cubic and hexagonal liquid crystals are 10.53 and 5.68 nm, respectively.     

介观化学体系中的动力学尺度效应

以生命和表面催化体系为对象，研究了介观化学体系中内涨落对体系非线性动力学行为的调控作用。内涨落可以诱导随机振荡，其强度在体系处于最佳尺度时会出现一个甚至多个极大值，并且在耦合体系中会得到进一步增强，表现为尺度共振效应、尺度选择效应和双重尺度效应，揭示了介观化学体系中尺度效应的新机制。     

LIGHT-SCATTERING STUDY OF POLYELECTROLYTE HOLLOW CAPSULES

Silver halide (AgX) microcrystal was used as template to synthesize hollow polyelectrolyte capsules. These hollow capsules were characterized by laser light scattering (LLS) used to measure the size of the capsules in solution. The ratio of hydrodynamic radius (Rh) from dynamic LLS to the radius of gyration (Rg) from static LLS is almost unity, revealing that the entities are hollow in solution. The results suggest that the LLS method can be regarded as a good complement to the confocal laser scanning microscopy (CLSM) method for the characterization of small hollow capsules, and it possesses the advantage of not needing fluorescence labeling.     

Pore size distributions in low‐k dielectric thin films from X‐ray porosimetry

X‐ray reflectivity has been used to determine the mass uptake of probe molecules in porous thin films supported on thick silicon wafers. The adsorption occurs by capillary condensation when the films are exposed to probe vapor at controlled partial vapor pressures. The probe solvent partial pressure was varied by mixing saturated air and dry air at constant temperature or by changing sample temperature at a constant vapor concentration. Pore size distribution in the films can be calculated from the probe uptake with typical porosimetric approaches such as the application of the Kelvin equation to convert partial pressure into pore size. For illustration, the pore size distribution of three different nanoporous thin films, the primary candidate of ultra‐low‐k interlevel dielectrics in the next generation of integrated circuit chips, was determined with this technique. These samples represent different generations of low‐k dielectrics developed by industry. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2170–2177, 2002     

Studies on the porous structure of di(methacryloyloxymethyl) naphthalene-divinylbenzene copolymers by inverse exclusion chromatography

Summary Using inverse exclusion chromatography the porous structure of the copolymers of di(methacryloyloxymethyl)naphthalenes and divinylbenzene was investigated.In order to determine the pore size distributions of the copolymers, toluene, alkylphenones, phthalates and polystyrene standards were used as the probes.The measurements proved that the existence of micropores depend on the method of copolymerization. The copolymers obtained by suspension and emulsion methods are more or less microporous, but the copolymer prepared by thermal polymerization in mass does not include micropores in its internal structure.     

化学蒸气沉积硅氧化合物调变HZSM－5沸石的研究

本文研究了正硅酸乙酯分别在无胺法和有胺法制得的ＨＺＳＭ－５沸石上的沉积过程，并用吸附，ＮＨ３－ＴＰＤ及异丙醇探针反应等手段表征了沉积后的样品，发现沉积仅在外表面上进行，可使孔口变小但不影响孔道内性质，显示有对于二甲苯分子的择形吸附能力，且在甲苯甲醇烷基化反应和二甲苯异构化反应中表现出良好的择形催化性能．     

氧化钇粒度控制与测定

用氨水或碳酸氢铵与氯化钇溶液反应生成沉淀，煅烧沉淀制备了D50为0．45μmt 2-10μm的各种粒径的氧化钇粉末。分别采用Coulter MultisizerⅡ和90Plus粒度仪测定微米和亚微米级氧化钇粉体粒度，研究了分散剂，待测样品量，分散时间等因素对亚微米级氧化钇粉体粒度测量精度的影响。     

Effect of NaOH and NaCl on the disodiumn-decane phosphonate micellar aggregation number

The diffusion coefficient of disodiumn-decane phosphonate micelles was studied by polarography at 25°C in NaCl and in NaOH solutions, and the size and aggregation number of the micelles was computed as a function of Na⁺ concentration. All other conditions being equal, the addition of NaCl produces micelles with an aggregation number one order of magnitude larger than the NaOH addition. This is due to the increase of the effective charge per micellized head group produced by the reaction of OH- with the hydrolized head groups which are mainly present as-PO₃H- in the micellar Stern layer.     

Physico-chemical characterization of nanofiltration membranes.

This study presents a methodology for an in-depth characterization of six representative commercial nanofiltration membranes. Laboratory-made polyethersulfone membranes are included for reference. Besides the physical characterization [molecular weight cut-off (MWCO), surface charge, roughness and hydrophobicity], the membranes are also studied for their chemical composition [attenuated total reflectance Fourier spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS)] and porosity [positron annihilation spectroscopy (PAS)]. The chemical characterization indicates that all membranes are composed of at least two different layers. The presence of an additional third layer is proved and studied for membranes with a polyamide top layer. PAS experiments, in combination with FIB (focused ion beam) images, show that these membranes also have a thinner and a less porous skin layer (upper part of the top layer). In the skin layer, two different pore sizes are observed for all commercial membranes: a pore size of 1.25-1.55 angstroms as well as a pore size of 3.20-3.95 angstroms (both depending on the membrane type). Thus, the pore size distribution in nanofiltration membranes is bimodal, in contrast to the generally accepted log-normal distribution. Although the pore sizes are rather similar for all commercial membranes, their pore volume fraction and hence their porosity differ significantly.