一种新的超分辨记录点的读出技术

提出一种新的超分辨记录点的读出技术—超分辨反射膜技术，详细分析了其原理。用该技术，以Sb为超分辨反射膜，SiN为介电层，在激光波长为632．8nm和光学头的数值也径为0．40的读出光学系统中实现了直径为380nm的超分辨记录点的读出。同时研究了Sb薄膜厚度对读出信噪比的影响规律，发现最佳的Sb薄膜厚度为28～30nm，所得的信噪比为38～40dB。     

Rotation of a Fine Particle with Circularly Polarized Anti-Parallel Collinear Laser Beams

We have succeeded in the operation of rotating a fine particle which was held without mechanical contact by circularly polarized laser beams with opposite propagation directions. A polystyrene latex particle 11.9 μm in diameter deformed in a disk-like shape was dispersed in water, and was trapped using the anti-parallel collinear laser beams which were set up so that they had the circular polarization rotating in the same direction. It was observed that the trapped particle rotated in the same direction as the rotation of the circular polarization of light. Inversion of the rotational direction of the circular polarization of light reversed the direction of the rotation of the particle. Although the rotational speed of a particle varied significantly from particle to particle, it was found to be proportional to the laser beam intensity. A typical value for the rotational speed per beam intensity was 2.1 Hz/W.     

板状激光振荡介质温度场和应力场的数值模拟

以非均匀内热源模型为基础,并考虑材料的导热系数和热膨胀系数的温度相关性,利用有限元方法,对板状激光振荡介质在不同功率和冷却强度下的温度和热应力分布进行了数值模拟及分析。根据计算结果提出了最大有效换热系数的概念,指出换热系数超过最大有效换热系数后,继续强化传热对减小高功率激光器的热效应已无明显效果。以此得出采用常规冷却技术所允许的最大泵浦加热功率。     

一种控制掺铒光纤激光器超混沌的方法——非线性延时反馈参数调制法

提出一种非线性延时反馈参数调制法来控制混沌/超混沌，给出了利用这种方法控制处于超混沌状态的双环掺铒光纤激光器的方案.数值模拟表明，只要延时时间和反馈强度合适就可以把双环掺铒光纤激光器从超混沌状态成功地控制到不同的周期状态. 关键词： 掺铒光纤激光器 超混沌 非线性延时反馈参数调制 混沌控制     

几种常见光源特性的研究

本通过大学物理实验中常用光源特性的分析，说明了实验中光源使用的合理性。     

Study of the pulsed laser vapor doping of Si(1 0 0) with KrF excimer laser and BCl3 gas

The properties of pulsed laser vapor doping on p-Si(1 0 0) with a KrF (248 nm) excimer pulsed laser (248 nm) and BCl₃ gas are reported in this paper. The doped samples are characterized by the resistance measured using a four-probe method, since the sheet resistance changes with the carrier concentration of the sample. The doping effects with the variation of laser energy density, pulse number, and the pressure of BCl₃ were investigated in terms of the sheet resistance. In this way, the optimized parameters were obtained and used for the positive heavy doping on p-Si(1 0 0) and p-Si(1 1 1). Then, using a square mesh under the above conditions, an image doping was completed. Finally, the metal–semiconductor Ohmic contacts were realized by plating Ag and Cu films on the doped surface.     

Chip-calorimeter for small samples

A method for measuring heat capacities of small samples using a chip-calorimeter and a heat pulse technique is described. The theoretical background to calculate the heat transport properties and the heat capacity of the sample from the pulse response function is given. Problems and potentials of the method are discussed. An example is given.     

同轴双无衍射光的理论与实验

提出同轴双无衍射光的概念。如果两束汇聚角略有不同的同轴无衍射光同时存在，则它们相互之间叠加干涉后产生一种纵向呈周期变化的光场结构，这是一种新的光束空间分布，这种光束在横向仍是一种同心环光斑，可用于精密对准。而在不同纵向位置，这些同心环的强度分布是不同的，且是周期性变化的。同轴双无衍射光的轴向周期性可用于沿光束传播方向的定位。文中提出了双环缝法、分段圆锥透镜法、正弦相位环光栅法等实现同轴双无衍射光的理论与实验方法，分析了同轴双无衍射光的横向与纵向传播的衍射光斑特性，理论计算与实验测量的结果基本相符合。     

Towards the synthesis of MAX-phase functional coatings by pulsed laser deposition

Pulsed laser deposition with a Nd:YAG laser was used to grow thin films from a pre-synthesized Ti₃SiC₂ MAX-phase formulated ablation target on oxidized Si(1 0 0) and MgO(1 0 0) substrates. The depositions were carried out in a substrate temperature range from 300 to 900 K, and the pressure in the deposition chamber ranged from vacuum (10⁻⁵ Pa) to 0.05 Pa Argon background pressure. The properties of the films have been investigated by Rutherford backscattering spectrometry for film thickness and stoichiometric composition and X-ray diffraction for the crystallinity of the films. The silicon content of the films varied with the energy density of the laser beam. To suppress especially the silicon re-sputtering from the substrate, the energy of the incoming particles must be below a threshold of 20 eV. Therefore, the energy density of the laser beam must not be too high. At constant deposition energy density the film thickness depends strongly on the background pressure. The X-ray diffraction measurements show patterns that are typical of amorphous films, i.e. no Ti₃SiC₂ related reflections were found. Only a very weak TiC(2 0 0) reflection was seen, indicating the presence of a small amount of crystalline TiC.     

A simple model for high fluence ultra-short pulsed laser metal ablation

The ultra-short laser metal ablation is a very complex process, the complete simulation of which requires applications of complicated hydrodynamics or molecular dynamics models, which, however, are often time-consuming and difficult to apply. For many practical applications, where the laser ablation depth is the main concern, a simplified model that is easy to apply but at the same time can also provide reasonably accurate predictions of ablation depth is very desirable. Such a model has been developed and presented in this paper, which has been found to be applicable for laser pulse duration up to 10 ps based on comparisons of model predictions with experimental measurements.