Picosecond nonlinear optical response of Ba0.5Sr0.5TiO3 thin films fabricated by pulsed laser deposition

Well-crystallized Ba_0.5Sr_0.5TiO₃ thin films with good surface morphology were prepared on MgO(1 0 0) substrates by pulsed laser deposition technique at a deposition temperature of 800 °C under the oxygen pressure of 2 × 10⁻³ Pa. X-ray diffraction and atomic force microscopy were used to characterize the films. The full width at half maximum of the (0 0 2) Ba_0.5Sr_0.5TiO₃ rocking curve and the root-mean-square surface roughness within the 5 μm × 5 μm area were 0.542° and 0.555 nm, respectively. The nonlinear optical properties of the films were determined by a single beam Z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that Ba_0.5Sr_0.5TiO₃ thin films exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 5.04 × 10⁻⁶ cm²/kW and β = 3.59 × 10⁻⁶ (m/W), respectively.     

Structural and electrical characterisation of La0.5Ca0.5MnO3 thin films grown by pulsed laser deposition

Thin films of perovskite manganite, with nominal composition La_0.5Ca_0.5MnO₃, have been prepared by pulsed laser deposition on (1 0 0) SrTiO₃, (1 0 0) LaAlO₃, (1 0 0) Si and YSZ/CeO₂-buffered (1 0 0) Si substrates. Structural and electrical characterisation was performed on the films. The magneto-transport properties of all the thin films depart from the bulk behaviour. The LCMO film grown on buffered Si shows an insulator–metallic transition around 130–150 K while the one deposited directly on Si displayed a similar behaviour under a melting field of 1 T. However, that transition is absent in the films grown on LAO and STO. We suggest that appropriate stress values induced by the substrate favour the formation of metallic percolative paths.     

Structure and optical properties of sol–gel derived Gd2O3 waveguide films

Pure and rare earth doped gadolinium oxide (Gd₂O₃) waveguide films were prepared by a simple sol–gel process and dip-coating method. Gd₂O₃ was successfully synthesized by hydrolysis of gadolinium acetate. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study the thermal chemistry properties of dried gel. Structure of Gd₂O₃ films annealed at different temperature ranging from 400 to 750 °C were investigated by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that Gd₂O₃ starts crystallizing at about 400 °C and the crystallite size increases with annealing temperature. Oriented growth of (4 0 0) face of Gd₂O₃ has been observed when the films were deposited on (1 0 0) Si substrate and annealed at 750 °C. The laser beam (λ=632.8 nm) was coupled into the film by a prism coupler and propagation loss of the film measured by scattering-detection method is about 2 dB/cm. Luminescence properties of europium ions doped films were measured and are discussed.     

Study on electroluminescence processes in dye-doped organic light-emitting diodes

Electroluminescence (EL) mechanism of dye-doped organic light-emitting diodes (OLEDs) was investigated by using three familiar fluorescent dyes, i.e., 5,12-Dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA), 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), and 5,6,11,12-tetraphenylnaphthacene (Rubrene). EL spectra of the doped devices with structure of indium tin oxide (ITO)/N,N′-bis-(1-naphthyl)-N,N′-diphenyl-1,1′-biphenyl-4,4′- diamine (NPB) (40 nm)/tris-(8-hydroxyquinolate)-aluminum (Alq₃) (x nm, x=0–40 nm)/dye: Alq₃ (weight ratio≈1%, 2 nm)/Alq₃ (48−x nm)/MgAg indicated that direct carrier trapping (DCT) process dominated light emission of devices. As a result, investigation of carrier-recombination site via doping, which is conventionally applied in OLEDs, is questionable since the doping site and the dopant itself may significantly influence the carrier-recombination process in the doped devices.     

K离子掺杂增强NaErF4体系上转换发光

制备了一系列Na_1-xK_xErF₄@NaLuF₄的核壳纳米结构,核中K⁺掺杂摩尔分数变化范围为0%~8%。XRD分析结果揭示这些具有不同K掺杂浓度的纳米粒子均为β-相纳米结构。研究结果表明：随着K⁺浓度的增加,纳米结构中Er³⁺~650 nm处的红带发光强度呈现先增强后减弱的规律,当K⁺摩尔分数为4%时,Na_0.96K_0.04ErF₄@NaLuF₄纳米晶的发光强度达到最大,为未掺杂K⁺的NaErF₄@NaLuF₄纳米晶发光强度的3.7倍。其发光增强的原因在于K⁺的掺杂降低了Er³⁺微环境晶场宇称对称性,提高了Er³⁺离子⁴F_9/2→⁴I_5/2能级辐射跃迁几率,进而增强了Er³⁺的650 nm红带的上转换发光强度。     

梯度掺杂体异质结对有机太阳能电池光电转换效率的影响

基于传统的体异质结有机太阳能电池结构, 对结构中的混合层改用梯度掺杂的方法, 在AM1.5, 100 mW/cm²光照下, 使得器件的短路电流由原来的7.72 mA/cm²提高到了9.18 mA/cm², 相应的光电转换效率提高了25%. 器件性能的提升归因于梯度掺杂体系的引入使得体异质结混合层中同一材料分子之间形成了较好的连续网络结构, 降低了器件的串联电阻, 提高了电极对载流子的收集效率, 从而提高了器件的光电转换效率. 关键词： 有机太阳能电池 体异质结 梯度掺杂     

基于SESAM被动调Q的激光二极管泵浦Yb∶CaYAlO_4脉冲激光器

采用发射波长约为976 nm的半导体激光器作为泵浦源,Yb~(3+)掺杂浓度为1. 5at.%、通光长度为2 mm的Yb∶CaYAlO_4晶体作为增益介质,本文提出了一种基于半导体可饱和吸收镜(SESAM)被动调Q的激光二极管泵浦Yb∶CaYAlO_4以获取稳定脉冲输出的方案。通过合理设计谐振腔,实现了稳定的被动调Q激光脉冲输出,并分析了泵浦功率的大小对输出脉冲的重复频率、脉冲宽度、单脉冲能量以及脉冲峰值功率的影响。     

Rapid nucleation of diamond films by pulsed laser chemical vapor deposition

The nucleation of diamond films could be greatly enhanced on mirror-polished Si substrate by a pulsed Nd:YAG laser beam without any thermal- and plasma-assisted processes during a very short time. The nucleation density increased with decreasing laser power density from 1.38×10¹⁰ to 1.17×10⁹ W/cm² and deposition pressure from 1013 to 4 mbar. The pulsed laser beam made no contribution to enhance nucleation at substrate temperature as low as 650°C. X-ray diffraction measurements showed the (1 1 1) diffraction peak of diamond for the samples obtained using only pulsed laser during 40 min. The enhanced nucleation and growth of diamond crystallites were attributed to effective excitation of reactive gases and etching of non-diamond carbon phases by the pulsed laser beam.     

Inert gas cutting of titanium sheet with pulsed mode CO2 laser

The present work aimed at studying the dynamic behavior of melt ejection in laser cutting of 1 mm thick titanium sheet and to obtain dross-free cuts with minimum heat affected zone (HAZ). CO₂ laser cutting of titanium sheet was carried out with continuous wave (CW) and pulsed mode laser operation with different shear gases namely argon, helium and nitrogen. Laser cutting with high frequency and low-duty cycle pulse mode operation produced dross-free cuts with no noticeable HAZ. Helium, because of its high heat convection and ability to generate high shear stress, produced laser-cuts with narrow HAZ and low dross, as compared to those produced with argon as the shear gas. Microscopic features of laser cut surfaces were analyzed and correlated with dynamic mechanism involved in laser cutting process. Process parameters for laser piercing, required for the initiation of fusion cut within the sheet, were also studied. Laser piercing requires either CW or high-duty cycle (>80%) pulse mode operation.     

Annealing effects on structure and laser-induced damage threshold of Ta2O5/SiO2 dielectric mirrors

The effects of annealing on structure and laser-induced damage threshold (LIDT) of Ta₂O₅/SiO₂ dielectric mirrors were investigated. Ta₂O₅/SiO₂ multilayer was prepared by ion beam sputtering (IBS), then annealed in air under the temperature from 100 to 400 °C. Microstructure of the samples was characterized by X-ray diffraction (XRD). Absorption of the multilayer was measured by surface thermal lensing (STL) technique. The laser-induced damage threshold was assessed using 1064 nm free pulsed laser at a pulse length of 220 μs.

It was found that the center wavelength shifted to long wavelength gradually as the annealing temperature increased, and kept its non-crystalline structure even after annealing. The absorbance of the reflectors decreased after annealing. A remarkable increase of the laser-induced damage threshold was found when the annealing temperature was above 250 °C.     

Laser-active colour centres with functional periodic structures in LiF fabricated by two interfering femtosecond laser pulses

We report a new technique to fabricate both laser-active F₂ and F₃⁺ colour centres in lithium fluoride and permanent periodic gratings with fringe spacings as fine as sub-micron size simultaneously by two interfering infrared femtosecond (fs) laser pulses. In particular, the optical properties of such colour centres produced by a single fs laser pulse are compared with those created by damage from radiation such as X-rays. Moreover, the present technique is applied to the first production of three-dimensional active channel waveguide and a pulsed distributed-feedback (DFB) laser at around 700 nm in LiF containing F₂ colour centres with fine-pitched micro-grating structures.     

Laser properties of different Nd-doped concentration Nd:YVO4 laser crystals

The laser outputs of 1.26, 0.95, 0.5 and 0.32 at% Nd-doped concentrations in Nd:YVO₄ crystal samples were performed under high pumping power of laser diode. The reason of different Nd-doped concentrations in Nd:YVO₄ crystals influencing on the laser output properties was explained. The intracavity double frequency laser outputs of Nd:YVO₄ crystal at 532 and 671 nm were also performed. Our experimental results show that the optimum Nd-doped concentration in Nd:YVO₄ crystal is about 0.5 at% under a pumping power of 30 W.     

Electronic conduction properties of Au/C60/p-Si and C60/Au/p-Si sandwich structures: I–V and transducer characteristics

Gold-fullerite [C₆₀]-silicon (p-type) sandwich structures have been fabricated in order to investigate intrinsic cross-sectional and planar electronic conductive properties, in particular the C₆₀/p-Si p–n heterojunction. The turn-on voltage of this p–n heterojunction lies in the range 0.25–0.27 V. The I–V characteristics of the Au/C₆₀/p-Si structure are mostly defined by the bulk specific resistance of the fullerite crystal film itself (6×10⁷ Ω cm). I–V curves in the C₆₀/Au/p-Si structure are shown to be ohmic. Au/C₆₀/p-Si sandwiches irradiated with swift (300 MeV) heavy ions, (⁸⁴Kr¹⁴⁺) to a total fluence 10¹⁰ ion/cm² yield structures which are sensitive to ambient air pressure, specifically in the case of a transverse contact configuration, and if one of the contacts is located on the irradiated part of the fullerite film. The sandwich-structure sensitivity to pressure is 5×10⁻⁶ Pa⁻¹. This exceeds the sensitivity of conventional silicon pressure transducers by almost three orders of magnitude.     

Analysis of frequency-dependent series resistance and interface states of In/SiO2/p-Si (MIS) structures

In this work, the investigation of the interface state density and series resistance from capacitance–voltage (C–V) and conductance–voltage (G/ω−V) characteristics in In/SiO₂/p-Si metal–insulator–semiconductor (MIS) structures with thin interfacial insulator layer have been reported. The thickness of SiO₂ film obtained from the measurement of the oxide capacitance corrected for series resistance in the strong accumulation region is 220 Å. The forward and reverse bias C–V and G/ω−V characteristics of MIS structures have been studied at the frequency range 30 kHz–1 MHz at room temperature. The frequency dispersion in capacitance and conductance can be interpreted in terms of the series resistance (R_s) and interface state density (D_it) values. Both the series resistance R_s and density of interface states D_it are strongly frequency-dependent and decrease with increasing frequency. The distribution profile of R_s–V gives a peak at low frequencies in the depletion region and disappears with increasing frequency. Experimental results show that the interfacial polarization contributes to the improvement of the dielectric properties of In/SiO₂/p-Si MIS structures. The interface state density value of In/SiO₂/p-Si MIS diode calculated at strong accumulation region is 1.11×10¹² eV⁻¹ cm⁻² at 1 MHz. It is found that the calculated value of D_it (≈10¹² eV⁻¹ cm⁻²) is not high enough to pin the Fermi level of the Si substrate disrupting the device operation.     

国产30/600μm掺镱光纤实现4.1kW激光输出

采用化学气相沉积结合气相/液相复合掺杂方式制备30/600 μm掺镱双包层光纤,石英纤芯中的掺杂组分为Yb₂O₃, Al₂O₃,P₂O₅。基于976 nm发光二极管反向抽运方式,构建全光纤化的主控振荡器功率放大器结构对增益光纤进行测试。实验中,种子源功率为189 W,当泵浦总功率为4747 W时,激光输出功率为4120 W,放大级光光效率为85%,3 dB带宽为1.6 nm。激光器连续工作1 h,激光功率稳定在4100 W,未发生明显的功率衰退现象。     

梯度掺杂对n型异质结太阳能电池性能的影响

通过仿真软件AFORS-HET对a-Si:H(p)/i-a-Si:H/c-Si(n)异质结太阳能电池的光伏特性进行分析及优化,主要对比了a-Si:H(p)层的均匀掺杂和表面掺杂浓度D₁=1×10²⁰ cm^-3>界面掺杂浓度D₂=4×10¹⁹ cm^-3的梯度掺杂情况时的光伏特性,实现了在梯度掺杂时22.32%的光电转换效率。与均匀梯度掺杂相比,发射层的梯度掺杂除了引入一个附加电场,还优化了能带结构、光谱响应、表面复合速率。结果表明,梯度掺杂可以有效地改善电池的光电转换性能。     

Tantalum irradiation by high power pulsed laser at 1315 and 438 nm wavelengths

The high power pulsed laser Prague asterix laser system (PALS), operating at the fundamental (1ω) and third (3ω) harmonics (1315 and 438 nm wavelengths, respectively), is employed in a single-shot mode to irradiate tantalum targets in vacuum. The laser pulse width is 400 ps and the laser pulse energy ranges between 43 and 736 J at 1ω and between 12 and 230 J at 3ω. High ablation yields (0.1–0.6 mg per pulse) are measured as a function of the laser pulse energy at both wavelengths; at 438 nm higher etching rates are observed. The produced craters are analysed by the scanning electron microscope (SEM) and by the high sensitivity surface profiler system. They are investigated in dimension, shape and angle aperture as a function of the incident laser energy. Different possible mechanisms responsible for the different crater shapes are presented and discussed.     

Influence of silver doping on the photocatalytic activity of titania films

By means of X-ray diffraction, BET nitrogen adsorption, UV-Vis-NIR transmission spectroscopy, transmission electron microscope, scanning electron microscope, X-ray photoelectron spectroscopy and photodegradation of methylene blue, effects of Ag doping on the microstructure and photocatalytic activity of TiO₂ films prepared by sol–gel method were studied. It is found that with a suitable amount (2–4 mol%), the Ag dopant increases the photocatalytic activity of TiO₂ films. The mechanism can be attributed to that (1) anatase grain sizes decrease with Ag doping and the specific surface areas of doped TiO₂ films increase, the charge transfer in TiO₂ films is promoted; (2) by enhancing the electron–hole pairs separation and inhibiting their recombination, the Ag dopant enhances the charge pair separation efficiency for doped TiO₂ films.     

Green electroluminescence from an n-ZnO: Er/p-Si heterostructured light-emitting diode

Erbium-doped ZnO (ZnO:Er) thin films with various doping concentrations were deposited on p-Si substrates by ultrasonic spray pyrolysis (USP). The n-ZnO:Er/p-Si heterojunctions were further employed to fabricate light-emitting diodes (LEDs). The devices showed diode-like rectifying current–voltage characteristics with a low reverse breakdown voltage, attributed to the avalanche breakdown. A distinct green electroluminescence peaking at 537 nm and 558 nm were observed at room temperature under reverse bias. The green electroluminescence originated from the electron impact excitation of Er³⁺ ions doped in ZnO films.     

Effect of different oxidizing gases on the in-situ growth of YBa2Cu3O7−δ films by pulsed laser deposition

The effectiveness of oxygen (O₂), nitrous oxide (N₂O), and nitrogen dioxide (NO₂) as oxidizing agents during in-situ growth of YBa₂Cu₃O_7−δ (YBCO) films on (100) SrTiO₃ substrates by pulsed laser deposition has been studied as a function of deposition temperature (700–800°C), and laser wavelength (193,248 and 355 nm), for a wide range of oxidizer gas pressure (0.1–200 mTorr). In general, the superconducting transition temperature of the films has been found to increase with increasing oxidant pressure, with zero-resistance temperature ≈90 K only obtained in films prepared in a relatively high pressure (150–200 mTorr) of oxidizer gas. At lower pressures, the transition temperature while being depressed is quite sensitive to the nature of the oxidant, the laser wavelength and the deposition temperature. Nevertheless, independent of the oxygen source or other growth parameters, an almost linear decrease in transition temperature with a corresponding increase in the c-axis lattice parameter has been observed for all the film. YBCO films have also been deposited in a low pressure background (≤ 1 mTorr) using a combination of atomic oxygen and pulsed molecular oxygen. The results are discussed in terms of the oxygen requirement for kinetic and thermodynamic stability of YBCO during growth of the film by pulsed laser deposition.