In situ monitoring of the H concentration change near an electrode surface through electrolysis using slab optical waveguide pH sensor

The H⁺ concentration change was monitored near an electrode surface through an electrolysis using a slab optical waveguide technique. Indium tin oxide transparent electrode modified by porous insulating polymer to which methyl red was covalently immobilized was used as a guiding layer, and the absorbance change of the polymer film was monitored. H⁺ generation at the vicinity of the electrode through the oxidation of ascorbic acid could be monitored by this technique.     

质子交换MgO:LiNbO3波导的双层结构

本文报导MgO:LiN_bO₃质子交换波导X射线双晶衍射和红外吸收的实验结果。这些结果表明质子交换波导由浅表面层和深表面层构成。浅表面层是一个连续应变层,有着大量随机排列的O—H—O形式的缔合OH^-基团。深表面层是一个均匀应变层,其内H⁺以自由OH^-基团形式出现。质子交换波导折射串不稳定性与双层结构中的结构驰豫密切相关。通过对质子交换过程的分析,提出两条避免双层结构的途径,其一为降低交换剂中的H⁺浓度,另一条是采用有限源工艺。     

毫米波圆柱波导自由电子激光放大器的数值模拟

本文以单粒子理论为基础，在不计空间电荷效应的近似条件下推导了带轴向引导磁场的三维圆柱波导非线性模拟方程组。用CAGFEL程序计算、分析了在带入口区、常数摇摆器条件下两组不同物理参数的自由电子激光放大器的物理模型。计算结果可靠，物理图象合理。对于其中的第二组参数还着重考查了光波频率、输入功率和摇摆器场振幅改变对输出功率和效率的影响。上述这些计算结果对0．7MeV 自由电子激光放大器的设计和实验具有一定的参考价值。     

光子晶体平面波导与脊波导高效耦合技术的研究

利用一维变周期谐振腔阵列和非线性缓变边界，可以实现光波从脊波导到光子晶体平面波导 （PCW）的高效耦合.基于平面波展开法（PWE）和时域有限差分法（FDTD），深入分析和讨 论了普通脊波导、2D-PCW结构和本征模以及工作模式、缓变边界形状等对耦合效率的影响， 从而得出光波从脊波导到2D-PCW、再返回脊波导的统一图景.指出考虑模式转换和采用缓变 边界条件可以极大提高PCW与脊波导间的耦合效率.对PC-PW边界采用线性和非线性缓变结构 进行了仿真，讨论了边界缓变程度对耦合效率的影响.结果表明，采用模式耦合和PC-PW余弦 缓变边界时的耦合效率在较宽的带宽内超过了95%. 关键词： 光子晶体波导 脊波导 PWE FDTD 耦合边界     

利用泄漏波导测量低折射率薄膜的折射率和厚度

根据泄漏波导原理对K_9玻璃基板上的冰晶石薄膜进行折射率测量,达到的精度为1×10~(-4),与真实波导的情况相似。文中讨论了利用添加高折射率薄层减小待测薄膜的最小厚度的可能性。文中还利用光电方法观察反射光中暗条纹的方法判别波导的激发,并测出了冰晶石薄膜在4500到6500范围内的折射率。     

亚波长尺度下混合等离子泄漏模式激光

由于光存在衍射极限,因此传统方法不能实现亚波长尺度下的激光激射。为了打破这一衍射极限,本文设计了金属-介电层-半导体堆叠结构来实现深亚波长尺度下的激光激射,并讨论了相关结构对模式传播的影响。结构设计上,采用低介电常数金属银作为衬底、10 nm厚的LiF作为介电层、具有六边形截面的半导体纳米线ZnO作为高介电常数层,采用有限差分本征模和时域有限差分方法对所设计的结构进行光学仿真模拟。首先,通过改变ZnO纳米线的直径,使用有限本征模方法分析介电层中的光学模式,得到4种模式分布。然后,通过这4种光学模式在不同纳米线直径下的有效折射率和损耗计算了对应的波导传输距离以及激射阈值增益。最后,采用三维时域有限差分方法仿真分析纳米线稳态激光发射过程中各模式的电场分布。结果表明:在纳米线和金属衬底之间的介电层上存在混合等离子体模式和混合电模式,对于直径低于75 nm的ZnO纳米线,没有有效的物理光学模式,即混合等离子体模式和混合电模式都被切断,当ZnO纳米线的直径大于75 nm时,混合等离子体模式可以有效存在,而混合电模式在ZnO纳米线的直径达到120 nm之后才出现。虽然混合等离子体模式可以更好地限制在介电层中,但是它们的模式损耗太大,传播距离相对较小。此外,与混合等离子体模式相比,混合电模式的传播距离更长。在给定微米线的直径(D=240μm)下,混合电模式传播距离超过50μm。综上可知,在深亚波长尺度下利用混合泄漏模式可以打破光学衍射极限并实现激光激射。     

有机/无机复合功能材料倒脊型波导热光开关

利用溶胶-凝胶技术自主合成了一种具有优良光学特性和高热稳定性的有机/无机复合芯层材料.这种功能材料的分子中含有有机柔性侧链,可形成环氧交联.与无机SiO2-TiO2体系相比,具有较高的热光系数(量级为10-4/K),以及更好的成膜性和可加工性.通过与实验室自行配制的P(MMA-GMA)包层材料相匹配,设计制备了基于这种有机/无机复合功能材料的倒脊型波导马赫-曾德尔型热光开关.器件的波导与热电极性能良好.插入损耗为10dB,驱动功率15mW,开关时间小于1ms,消光比15dB.     

Numerical study of an ion-exchanged glass waveguide using both two-dimensional and three-dimensional models

A numerical study is carried out to compare the two-dimensional (2-D) case and three-dimensional (3-D) case for the modelling of an ion-exchanged glass waveguide. It is shown that different waveguide widths on the photomask correspond to different ion concentration distributions after an annealing process. A numerical example is presented of two waveguide sections with different widths indicates that due to the abrupt change of the waveguide width, a 3-D theoretical model is required for an accurate prediction of the parameters of ion-exchanged glass waveguides. The good agreement between the modelled and measured results proves that the developed 3-D numerical model can be beneficially utilized in the generalized design of optical devices based on ion-exchange waveguides.     

Athermal metal-free planar waveguide concave grating demultiplexer

An athermal metal-free planar waveguide concave grating demultiplexer is proposed. We designed the dielectric mirror at the grating facet instead of coating with the metal on the back wall of the grating facet. The transfer-matrix method is introduced to design the dielectric mirror and the reflectance spectral responses of the 2D waveguide structure are simulated using the FDTD software (RSoft, Inc.). To reduce the temperature sensitivity of the device, the three-focal-point method is introduced. We use the design example to show the high-reflectance bandwidth of the dielectric mirror. The fabrication errors are also taken into consideration. By using the numerical model of the scalar diffraction theory, the flat-top spectral responses of the channels are simulated.     

Directional coupler design based on coupled cavity waveguides in photonic crystals

We propose a directional coupler design based on coupled cavity waveguide in photonic crystals. The plane wave expansion is used to give the dispersion of the coupled cavity waveguides and two parallel such waveguides. The couple length is got from the dispersion curves. Based on the research of the dispersion, we present a directional coupler and the transmission property is given. This structure is potentially important for highly efficient directional coupler in integrate optical circuit.