滤波器对偏振模色散的补偿

根据耦合非线性薛定谔方程 ,本文研究了偏振模色散如何影响各种码型的频谱 ,分析了滑频滤波器和固定滤波器对偏振模色散的补偿作用。研究结果表明 :偏振模色散对不同码型的频谱影响是不一样的 ,对色散管理孤子的频谱影响最大 ,产生新的频率分量也最多 ,而且每个新频率分量都较强 ,比入射频谱展宽许多 ;滑频滤波器和固定滤波器对偏振模色散都具有补偿作用 ,使最大可传输距离成倍增加 ,两种滤波器对偏振模色散的补偿作用相差较小 ;但是对色散管理孤子系统中的偏振模色散补偿效果最佳。     

Φ520mmF/1.6椭球面反射镜加工

介绍了一块Φ520mm大相对孔径(F/1.6)轻量化椭球面反射镜的加工与检测方法。镜面的有效口径为Φ502mm,顶点曲率半径为1600mm,非球面系数k=-0.9663,面形精度要求优于0.025λ(RMS)。镜子背面有54个大小深浅不一的不通孔,用于减轻镜子的重量。采用WYKO干涉仪检测得到镜面面形误差达RMS0.02λ,λ=632.8nm。     

光子晶体反常色散超窄带滤波理论

讨论了利用由反常色散材料构成的二维（2D）光子晶体(PCs)实现超窄带滤波（PCADOF）的原理，并对铯原子蒸气6P3/2←6S1/2谱线的反常色散曲线进行了研究，讨论利用此反常色散曲线通过2D PCs实现超窄带滤波的方法和特点，研究发现这种滤光器的带宽可达到0.002nm，这将为设计一种全新的滤波器提供指导. 关键词： 反常色散 光子晶体 超窄带滤波     

能动反射镜低频像差补偿能力分析

 采用Algor软件包并利用有限元法对37单元能动反射镜低频误差补偿能力进行了分析计算，确定了镜面厚度8mm，驱动器间距46mm，极头直径12mm等能动反射镜制造的关键参数。通过计算机仿真分析证明，基于这些参数所设计的能动反射镜可以对低频误差进行有效校正，校正精度的均方根值小于等于λ／８，从而可以为能动反射镜的制造提供理论依据。     

大气气溶胶粒子光吸收系数的测量

 采用核孔过滤膜累积气溶胶粒子的方法设计了气溶胶粒子光吸收系数的测量系统。该系统由双光路组成,可以减小光路损耗和电路噪声带来的各种测量误差。同时，具有体积小、光路易于调节、可进行实时测量、定标容易等特点。用200和400nm孔径的过滤膜，分别测量了实验室内大气气溶胶粒子对不同波长激光的吸收系数。随着累积时间的增加，系统的测量精度也不断的提高，在累积时间为900s时，系统测量误差为9.849×10^-6/m。     

Ground-state complex formation of perylene with pyromellitic dianhydride studied by static fluorescence quenching

The association of complex formation with static quenching in CT systems was investigated. Evaluation of the data made evident that the inner filter effect must be allowed for. Time-resolved and temperature-dependent stationary measurements of fluorescence led to the separation of dynamic and static quenching components. The static quenching constant is discussed with respect to the equilibrium constant of complex formation determined by absorption spectroscopy.     

用多路逆磁系统测量热电子环磁镜中热电子沿轴向的分布

本文介绍了多路逆磁测量方法及利用这一方法在ＨＥＲ装置上测量热电子环沿轴向的长度与晃荡电子密度的轴向分布的实验结果。     

Application of Novel Focusing Mirrors in Gyrotron Transmission Lines

A novel focusing mirror based on the shifting of the beam phase according to the Gaussian beam optics enabled us to realize a focusing elements with different focal lengths in different directions and to convert the gyrotron output into a Gaussian-like beam. In this paper, we compare the quality of beams produced by the new system (which includes novel mirrors) and a conventional system consisting of a quasi-optical antenna, an ellipsoidal mirror and two parabolic cylinder mirrors.     

基于CCD采集的Mach-Zehnder干涉条纹图的处理算法

Mach-Zehnder干涉仪适用于研究气体密度迅速变化的状态。由于气体折射率的变化与其密度的变化成正比,而折射率的变化将使通过气体的光线有不同的光程,因此可通过干涉臂变化对干涉条纹图像效果的影响得到气体密度。实测中,采用图像采集卡和CCD来接收Mach-Zehnder干涉仪产生的条纹图像,再通过计算机对条纹图像的条纹间距进行处理,从而得到气体密度的变化状态。从光干涉理论出发,对Mach-Zehnder干涉条纹图像特征进行了分析,建立了Mach-Zehnder干涉条纹的数学模型,并根据此模型设计了处理Mach-Zehnder干涉条纹图像的算法。算法包括图像的预处理(即图像的噪声提取)、图像的二值化及图像的细化。     

Study on the possibilities of controlling the laser output beam properties by an intracavity deformable mirror

The possibilities of controlling the laser beam properties by a deformable mirror introduced into the laser optical cavity were studied theoretically and experimentally. The experiments were performed under conditions of an industrial high power transverse flow cw CO₂ laser operating with a stable resonator of a folded configuration. A deformable bimorph mirror of a surface profile controlled by the voltage applied to the mirror electrodes is implemented to the laser system as a back cavity mirror or as a one of the inner folding mirrors. The near-and far-field characteristics of the laser beam versus the resonator configuration controlled by the changes of the focal length of the deformable mirror are discussed in the paper. The analysis reveals that the resonator with an inner deformable mirror is much more sensitive to the mirror curvature variations than the resonator in which the deformable mirror is used as a back cavity mirror. The presented results show that dynamic and controllable changes in the resonator properties result in the controlled modification and optimisation of the laser output power and spatial parameters of the laser radiation.