Chemical Liquid Phase Deposition of Thin Aluminum Oxide Films

Introduction Inorganic oxide films have attracted a lot of interest in the last several decades. Among them, silicon dioxide films are widely used in modern microelectronics, optics and mechanics. This material has been grown by various methods including thermal oxidation, chemical vapor phase deposition, plasma-enhanced chemical vapor phase deposition, and so on.1,2 Recently, Nagayama et al.3 have reported that SiO2 thin films could be produced by a new chemical method of liquid phase depos…     

MoO3、NiO、ZnO在小表面金红石上的分散行为

Dispersion of MoO3, NiO, ZnO on rutile TiO2 with low specific surface area was studied with Mercury Porosimeter, SEM, XPS and Ammonia Extraction method. The dispersion thresholds of MoO3, NiO, ZnO on three rutile TiO2 carriers were obtained with XPS, and com-pared with those on anatase TiO2 with high specific surf are area. Ammonia Extraction method was used to identify the surface oxide species interarting with support surface in different strength and it was found that the proportions of oxides that can not be extracted by ammonia extraction are different for MoO3, NiO and ZnO which are supported on rutile TiO2.     

CuO/γ-Al2O3单分散催化剂的XAFS研究

采用XAFS方法研究浸渍法制备并于低温焙烧的CuO/γ-Al2O3催化剂的局域结构.对于CuO负载量小于单层分散阈值的CuO/γ-Al2O3(0.4 mmol/100 m2),结果表明,CuO物种是以层状分散的孤立原子簇存在于γ-Al2O3载体表面,其第一近邻Cu－O配位环境的结构与晶态CuO的相似,键长和配位数分别为0.195 nm和4.对于CuO负载量等于单层分散阈值的CuO/γ-Al2O3(0.8 mmol/100 m2),已有少量的CuO纳米颗粒生成.对于CuO负载量大于单层分散阈值的CuO/γ-Al2O3(1.2 mmol/100 m2),其结构与多晶CuO的相近.基于CuO在γ-Al2O3载体上的三种不同分散状态的结构特点,我们提出了CuO/γ-Al2O3催化剂的结构模型.     

金属酞菁化合物在TiO2表面的分散研究

Dispersion of copper(Ⅱ) phthalocyanine (CuPc), copper(Ⅱ) phthalocyaninesulfonate (CuPcS) and cobalt(Ⅱ)phthalocyaninetetrasulfonate (CoPcTS) on the surface of titanium dioxide was investigated by XRD, XPS, FT-IR and UV-Vis techniques. Results show that interaction between CuPc and TiO2 was very weak and CuPc was difficult to disperse on the surface of the support. While partly sulfurized CuPcS could be dispersed on the surface of support through sulfo-groups and its dispersion capacity was determined to be 0.085 g CuPcS/g TiO2. Completely sulfurlzed CoPcTS could also be dispersed on the surface of TiO2 as a monolayer and its dispersion capacity was 0.12 g CoPcTS/g TiO2. Interactions of the sulfo-groups as well as the electrons of CoPcTS with the surface of TiO2 could be evidenced by FT-IR characterization. Therefore, it was suggested that CoPcTS molecules be adsorbed on the surface of TiO2 in a flat-lying mode while CuPcS in a slanting one. UV-Vis spectra show that the dispersed CuPcS and CoPcTS molecules exist in both forms of monomers and dimers.     

Application of matrix solid-phase dispersion in the analysis of priority polycyclic aromatic hydrocarbons in fish samples

The performance of matrix solid-phase dispersion (MSPD) for the extraction of polycyclic aromatic hydrocarbons (PAHs) in fish tissue is described. The suitability of different solid supports was tested as well as the influence on the extraction efficiency of the natural fat content in samples. Under optimal conditions 0.6-0.8 g of tissue sample, are dispersed with 2 g of octadecylsiloxane (C18) and 0.5 g of anhydrous sodium sulphate and transferred to the top of a polyethylene solid-phase extraction cartridge which already contains 2 g of florisil and 1 g of C18. Cartridges were eluted with acetonitrile. The analysis of the extracts was carried out by high-performance liquid chromatography (HPLC) coupled with fluorescence detection. The proposed method provides detection limits between 0.04 and 0.32 ng/g for the different considered PAHs, below the maximum levels established by the some regulatory bodies for the six PAHs after recent oil spill episodes and European Union regulations. Recoveries over 80% were obtained for all compounds. Accuracy validation was carried out using the US National Institute of Standards and Technology (NIST) SRM 2977 reference material.     

Advantages to Conversion of Lattice Heat Capacity to Cv in the Resolution of Excess Properties The Ln2S3's as an example

This paper represents a fitting (modeling) of the temperature dependence of the Komada-Westrum characteristic temperature for those γ-, δ- and ε-phase lanthanide sesquisulfides for which the total heat capacities, including internal degrees of freedom (e.g., Schottky and magnetic contributions), were connected to the residue of only lattice vibrations yielding lattice heat-capacity contributions. These characteristic temperatures (θ_KW) at 298.15 K are seen to behave smoothly (nearly linearly) as a function of (cationic) atomic number within the region of stability of each phase as does the density. The trends between the phases also show some consistency but not predictability of one from the other. This revised version was published online in July 2006 with corrections to the Cover Date.     

Mass distribution in a dynamic sample zone inside a flow injection manifold: modelling integrated conductimetric profiles

A mathematical model for fitting the experimental ICM (integrated conductimetric method) curves developed by the authors in a previous work, is presented for the first time in this study. The proposed model fits the experimental curves with great precision and allows to predict physical dispersion for single-line flow injection system. The correlation of the model’s parameters with typical reactionless FIA peak parameters is also assessed. The IDQ coefficient—a novel dispersion estimator previously reported by the authors—can also be predicted when operational FIA variables are changed. Experimental and modelled profiles are compared as a function of the system’s variables, showing an excellent agreement.     

Surface composition and property of film prepared with aqueous dispersion of polyurethaneurea-acrylate including fluorinated block copolymer

The aqueous dispersion of polyurethaneurea-acrylate (PUA) including small amount of fluorinated block copolymers containing carboxyl groups (PATF), which can be dissolved in water, was used to make films and the surface properties of these films were examined. The experimental data show that the modified PUA film exhibits a hydrophobic surface property, although the original surface of PUA film is hydrophilic. The surface composition of the modified PUA film was measured by ATR and XPS. The results indicate that there is a concentration gradient of the fluorine groups along the lines of thickness of the modified film and towards the outmost surface layer, resulting from the migration of fluorinated blocks to the air side surface of the modified PUA film during the film formation process. However, the PUA film can not be modified effectively by adding the sodium salt of PATF, since the urethane groups in the system are easy to occupy on the surface of the film.     

Thermal techniques to study complex elastomer/filler systems

The transfer of heat through an elastomeric matrix is important for both the processing of the material and its subsequent lifetime. Thermal conductivity can be used to evaluate the influence of different polymers and fillers on heat transfer. Additionally, the dispersion of the filler has an effect on heat transfer and thermal conductivity measurements can be used to provide semi-quantitative estimations of filler dispersion. The degradation of sulfur-crosslinked elastomer systems has been studied for many years. The degradation of the crosslinks (changes in sulfur rank) and degradation of the polymer backbone by thermal and/or oxidative processes have been studied extensively using many techniques including thermal analysis (references). However, the degradation of the crosslinked-polymer 'network' is less well understood. The relationship of the crosslink network to this degradation process is a key to both the long term and higher temperature performance of the sulfur-crosslinked elastomer. The changes in physical properties observed upon exposure of sulfur-crosslinked elastomers can be monitored using dynamic mechanical analysis. Subsequently, other thermal techniques can be used to monitor the chemistry that is occurring during these degradations. Thermal desorption/mass spectroscopy and dynamic scanning calorimetry are used to complete the picture of the degradation processes taking place. Examples of these techniques will be provided to illustrate the utility of the analytical approach, the chemistry involved in these degradation processes and the effect of changes in the polymer, cure package and other ingredients. This revised version was published online in August 2006 with corrections to the Cover Date.     

Polyaniline-coated silica gel

Silica gel microspheres 7 and 15 μm in diameter were coated with an overlayer of polyaniline camphorsulfonate or hydrochloride during the oxidative polymerization of aniline. Coated silica gel and polyaniline precipitate were separated using a difference in sedimentation rate. In an alternative approach, the microspheres were modified with polyaniline in the presence of 35 nm colloidal silica. This technique prevented the macroscopic precipitation of polyaniline. Coatings of neat, 3-aminopropyl- and octadecyl-modified silica gel with polyaniline hydrochloride were compared. The surface composition of coated microspheres was characterized by X-ray photoelectron spectroscopy. Potential applications of particles in electrorheology, organic catalysis, and in modeling of conductivity behavior in composites are demonstrated.