种子乳液聚合的研究进展

种子乳液聚合法因具有乳液稳定性更好、粒径分布窄、易控制等优点,在乳胶粒子设计及制备各种功能性胶乳方面具有重要作用,是制备高固含量乳液及具有核壳结构乳液的最常见最简便的方法.本文综述了近年来种子乳液的聚合工艺、聚合机理, 包括接枝机理、互穿聚合物网络机理、聚合物沉积机理、种子表面聚合机理和离子键合机理等,以及种子乳液聚合在乳胶粒子设计方面的应用研究进展,并讨论了影响种子乳液聚合的各种因素.     

不同种皮颜色花生糖含量近红外模型的构建

花生籽仁中的糖含量是影响食味品质的重要指标,建立快速测定糖含量的方法可有效提高食用型花生的检测效率。样品外观颜色是影响近红外分析的重要因素之一,按样品外观颜色分类定标（校正）更有利于提高模型的预测性能。研究选择不同糖含量的花生种质332个,采用色差仪将花生种质按种皮颜色分成黑紫色、红色和粉色三大类。采用3,5-二硝基水杨酸法、蒽酮乙酸乙酯法、蔗糖酶法分别测定籽粒中的总糖、可溶性糖及蔗糖含量。总糖含量分别在6.42%～39.53%（黑紫色籽粒）、9.66%～39.71%（红色籽粒）和8.52%～38.84%（粉色籽粒）之间;可溶性糖含量分别在2.4%～14.32%（黑紫色籽粒）、2.94%～13.75%（红色籽粒）和2.19%～14.53%（粉色籽粒）之间;蔗糖含量分别在0.92%～7.53%（黑紫色籽粒）、1.05%～7.23%（红色籽粒）和0.95%～7.99%（粉色籽粒）之间,变异系数均在33%以上。采用瑞典波通DA7250型近红外分析仪（950～1 650 nm）采集籽粒的近红外光谱值,选用基于全波段的偏最小二乘回归法（PLSR）,通过对比单一和复合预处理方法,对比模型的相关系数和误差确定最佳预测模型。分别建立了黑紫色、红色、粉色花生籽仁的总糖含量、可溶性糖含量和蔗糖含量的近红外光谱定标模型,共计9个模型,预测相关系数（R_c）在0.883～0.925之间,预测均方根误差（RMSEC）在0.370～1.988之间。对总糖含量所建立的模型中,粉色种皮花生的预测相关系数R_c可达0.925,RMSEC为1.705;对可溶性糖含量所建模型中,黑紫色种皮花生的预测相关系数R_c可达0.921,RMSEC为0.667;对蔗糖含量所建的模型中,粉色种皮花生的预测相关系数R_c可达0.914,RMSEC为0.435。并分别用15份种质进行外部验证,9个模型的预测相关系数R_p在0.892～0.967之间,预测均方根误差RMSEP在0.327～2.177之间。本研究建立的近红外光谱模型可同步、快速地检测花生籽粒中的多种糖含量,为高糖含量的鲜食花生育种提供了技术支持。     

Influence of wire mesh electrodes on the volume and surface characteristics of dielectric barrier discharge of atmospheric pressure helium

The dielectric barrier discharge of helium in a 6 mm gap at atmospheric pressure was studied. In this paper, the influence of electric field distribution on the uniformity of DBD is analyzed theoretically and verified by experiments. The experimental results show that the mesh electrode produces a local enhancement effect by affecting the electric field and then produces corona discharge, which provides seed electrons for the subsequent discharge process. The effects of mesh diameter and size on discharge uniformity and stability are analyzed, the electrode structure parameters are optimized, the method of a segmented electrode is proposed, and the discharge process and charge distribution are studied. The electrical diagnosis results of plasma technology show that the segmented mesh electrode reduces the breakdown voltage of DBD and increases the charge deposition.     

高效液相色谱-串联质谱法测定山茶油中黄曲霉毒素B1

建立了山茶油中黄曲霉毒素B1含量的高效液相色谱-串联质谱分析方法。通过对前处理方法的优化,选择了甲醇和水作为山茶油中黄曲霉毒素B1的提取溶剂,经免疫亲和柱富集浓缩后,采用高效液相色谱-串联质谱进行分析,经C18色谱柱分离,在电喷雾离子化正离子模式(ESI+)及多反应监测模式(MRM)下进行测定,基质匹配标准溶液外标法定量。在优化条件下,该方法线性范围为0.4～6.4μg/L,相关系数r2>0.998,最低检出限为0.026μg/kg,在添加水平为0.008,0.016和0.032μg时,方法回收率在85.9%～93.8%之间;相对标准偏差为1.8%～5.0%。方法可满足山茶油中黄曲霉毒素B1的检测要求。     

UPLC-MS/MS测定葡萄籽提取物中78种农药残留

建立了超高效液相色谱串联质谱法(UPLC-MS/MS)检测葡萄籽提取物中78种农药残留物的分析方法。样品用乙腈振荡提取,经乙二胺-N-丙基甲硅烷(PSA)和石墨化炭(GCB)固相萃取柱串联净化,乙腈-甲苯(V/V3:1)洗脱,洗脱液浓缩至约0.5 mL后,于45℃下氮气吹干,1.0 mL乙腈定容,UPLC-MS/MS测定,外标法定量。葡萄籽提取物中,78种农药在0.001～0.2μg/mL范围内线性关系均良好;所有农药的方法定量限(LOQ)均低于17.0μg/kg;在5,25,50μg/kg的添加水平下,葡萄籽提取物中78种农药的平均回收率处于72.6%～113.5%之间,相对标准偏差不大于11%。方法适用于葡萄籽提取物中78种农药残留的快速筛查测定。     

RRLC测定葡萄籽超临界CO2萃取液中的原花青素

用高分离度快速分离液相色谱法测定超临界葡萄籽萃取液中原花青素含量。色谱柱:ZorbaxXDB C18(4.6mm×50mm,1.8μm),柱温:40℃;流动相:1.5%乙酸甲醇-1.5%乙酸水(90:10,V/V);检测波长:280nm;进样量:5μL,流速:0.9mL/min。原花青素在0.60—3.6mg/mL(R2=0.9997)范围内峰面积与浓度呈良好线性关系,平均加标回收率为100.6%,RSD=1.07%(n=6)。方法简单、快速、准确、可靠,为原花青素含量测定提供一种新选择。     

对称性自发破缺所诱发的种子平行雷诺胁强

根据第二类气球模理论,在托卡马克中诸如不稳定漂移波类的环形局部模将在径向呈现源于环形性的对称性自发破缺。以流体离子温度梯度模模型方程为例,解出在准环坐标系中由对称性自发破缺产生的二维局部模本征模式。在略去边带效应后,它成为具有径向位移修正的平板模式。由位移修正离子温度梯度模式导出了种子平行雷诺胁强,而它在传统的(无位移修正的)平板模式下被证明为零。     

镶嵌型乳胶粒子的合成

以苯乙烯、甲基丙烯酸甲酯、丙烯腈等单体或它们的混合物为硬单体,天然胶乳为弹性组分,经多步种子乳液聚合法制得了在天然胶乳的粒子上镶嵌硬聚合物相的互穿网络型乳胶粒子.考察了十二烷基硫酸钠、十二烷基苯磺酸钠、壬基酚聚氧乙烯醚、油酸等乳化体系,过硫酸钾、过氧化苯甲酰热引发体系及异丙苯过氧化氢-四乙烯五胺、叔丁基过氧化氢-四乙烯五胺等氧化还原引发体系对聚合反应的影响.研究了交联剂用量对互穿结合率、溶胶含量的影响及溶胀时间、硬单体组成、乳化剂种类对乳胶粒子形态的影响,确定了适宜的聚合配方和工艺条件.透射电镜观察乳粒形态结果表明,单一使用极性或非极性单体,仅得到核-壳结构乳液,而采用不同极性单体复合、溶胀、互穿,得到的是镶嵌硬聚合物型乳粒结构.     

Infrared seed inspection system (IRSIS) on painted car shells

This paper describes a newly-developed automated thermal system for detection of seeds on newly painted car shells. The system’s novel approach is to use thermal emission; previously applied techniques relied on light reflection strategies. The system is described beginning with analytical modeling of the underlying detection theory to verification on a pilot run in an automotive production line. Parker’s flash procedure, using a thermal detector, was performed to extract the thermal properties of inspected panels. New computer logic developed in-house for processing the acquired thermograms is also presented.     

Effect of seeded surface area on crystal size distribution in glycine batch cooling crystallization: a seeding methodology

In batch cooling crystallization, if the seeding process is not carefully carried out, the crystal size distribution (CSD) is dispersed. The aim of this work is to determine the optimal conditions for seeding operations. Results show that the CSD is controlled if the seed surface area reaches a specific value called critical surface S_c. Nevertheless, S_c is not the only parameter to be considered. The mean crystal size of the product obtained actually depends on the size of the seeds used because of the growth rate distribution. In fact, seeds behave differently according to their crystal sizes, which accounts for the difference in crystal growth rates. Rules are proposed for seeding with the view to obtain a uni-modal CSD and a final product size predefined by the seed crystals.